• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.8
• /
• pp.603-611
• /
• 2020

A porous material which can contain liquid perfume was manufactured by adding 1~4 wt% of polysiloxane into a composite containing 20 ㎛ Ag powder and 30 wt% of 53 ㎛ salt, sintering for 60 min at 750℃, and melting salt selectively. The changes in pore, hardness, and microstructure were confirmed according to the polysiloxane content both before and after sintering. The manufactured silver liquid container was formed with open pores both before and after sintering, and the container shrunk by 2~7 % in both perpendicular and parallel directions after sintering. Vickers hardness was increased after sintering and was doubled when 2 wt% of polysiloxane was added. In case of the microstructure, the surface condition of the silver liquid container became darker according to the polysiloxane content, and the pore size was decreased from 50 ㎛ to under 10 ㎛. The composition distribution result revealed an even distribution when 2 wt% of polysiloxane was added but uneven distribution when over 3 wt% of polysiloxane was added due to decreased hardness by cluster. Therefore, the addition of an appropriate amount of 2 wt% polysiloxane reinforced the porous silver with open pores to offer application for jewelry usage.

• The Journal of the Acoustical Society of Korea
• /
• v.34 no.5
• /
• pp.335-342
• /
• 2015

Phononic crystals are composite materials consisting of a periodic arrangement of scattering inclusions in a host material. One of the most important properties of phononic crystals is the existence of band gaps, i.e., ranges of frequencies at which acoustic waves cannot propagate through the structure. The present study aims to investigate theoretically and experimentally the acoustic band structures in two-dimensional (2D) phononic crystals consisting of periodic square arrays of stainless steel solid cylinders with a diameter of 1 mm and a lattice constant of 1.5 mm in water. The theoretical dispersion relation that depicts the relationship between the frequency and the wave vector was calculated along the ${\Gamma}X$ direction of the first Brillouin zone using the finite element method to predict the band structures in the 2D phononic crystals. The transmission and the reflection coefficients were measured in the 2D phononic crystals with 1, 3, 5, 7, and 9 layers of stainless steel cylinders stacked in the perpendicular direction to propagation at normal incidence. The theoretical dispersion relation exhibited five band gaps at frequencies below 2 MHz, the first gap appearing around a frequency of 0.5 MHz. The location and the width of the band gaps experimentally observed in the transmission and the reflection coefficients appeared to coincide well with those determined from the theoretical dispersion relation.

• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.29 no.1
• /
• pp.51-57
• /
• 2023

Because of the global pollution caused by plastic disposal, demand for eco-friendly transformation in the packaging industry is increased. As part of that, the utilization of polylactic acid (PLA) as a food packaging material is increased. However, it is necessary to improve the crystallinity of PLA by adding nucleating agents or to improve the modulus by adding fillers because of the excessive brittleness of the PLA matrix. Thus, the cellulose nanofiber (CNF) was fabricated and dried to obtain a powder form and applied to the CNF/PLA nanocomposite. The effect of CNF on the morphological, thermal, rheological, and dynamic mechanical properties of the composite was analyzed. We can confirm the impregnated CNF particle in the PLA matrix through the field emission scanning electron microscope (FE-SEM). Differential scanning calorimetry (DSC) analysis showed that the crystallinity of not annealed CNF/PLA nanocomposite was increased approximately 2 and 4 times in the 1st and 2nd cycle, respectively, with the shift to lower temperature of cold crystallization temperature (T_cc) in the 2nd cycle. Moreover, the crystallinity of annealed CNF/PLA nanocomposite increased by 13.4%, and shifted T_cc was confirmed.

• Steel and Composite Structures
• /
• v.29 no.2
• /
• pp.273-286
• /
• 2018

In recent years, significant progress has been made in developing design rules for stainless steel members, while the investigation on bolted connections is relatively limited, in particular at elevated temperatures. In this paper, experimental and numerical investigations on stainless steel bolted connections at ambient and elevated temperatures from the literature were reviewed. Firstly, the research program that focused on structural behavior of cold-formed stainless steel (CFSS) bolted connections at elevated temperatures carried out by the authors were summarized. Over 400 CFSS single shear and double shear bolted connection specimens were tested. The tests were conducted in the temperature ranged from 22 to $950^{\circ}C$ using both steady state and transient state test methods. It is shown that the connection strengths decrease as the temperature increases in the similar manner for the steady state test results and the transient state test results. Generally, the deterioration of the connection strengths showed a similar tendency of reduction to those of the material properties for the same type of stainless steel regardless of different connection types and different configurations. It is also found that the austenitic stainless steel EN 1.4571 generally has better resistance than the stainless steel EN 1.4301 and EN 1.4162 for bolted connections at elevated temperatures. Secondly, extensive parametric studies that included 450 specimens were performed using the verified finite element models. Based on both the experimental and numerical results, bearing factors are proposed for bearing resistances of CFSS single shear and double shear bolted connections that subjected to bearing failure in the temperature ranged from 22 to $950^{\circ}C$. The bearing resistances of bolted connections obtained from the tests and numerical analyses were compared with the nominal strengths calculated from the current international stainless steel specifications, and also compared with the predicted strengths calculated using the proposed design equations. It is shown that the proposed design equations are generally more accurate and reliable than the current design rules in predicting the bearing resistances of CFSS (EN 1.4301, EN 1.4571 and EN 1.4162) bolted connections at elevated temperatures. Lastly, the proposed design rules were further assessed by the available 58 results of stainless steel bolted connections subjected to bearing failure in the literature. It is found that the proposed design rules are also applicable to the bearing resistance design of other stainless steel grades, including austenitic stainless steel (EN 1.4306), ferritic stainless steel (EN 1.4016) and duplex stainless steel (EN 1.4462).

• Membrane Journal
• /
• v.32 no.2
• /
• pp.133-139
• /
• 2022

As the issue of reducing greenhouse gases is emerging due to global warming and extreme weather, research on materials capable of radiative cooling without energy consumption is being actively conducted. Among them, silk is known as a natural self-cooling material, but in the conventional mixing process using chemically powdered silk, there is a problem that the radiative cooling effect disappears by the collapses of the intrinsic crystal structure of silk fibroin, so it is difficult to manufacture it in the form of a film or coating agent for radiative cooling. In this study, various types of membranes were manufactured using silk powder that went through a physical pulverization process that does not damage the intrinsic structure of silk fibroin, and the study was conducted to examine its applicability as a coating agent. Electrospun membranes and flat sheet membranes were prepared by using silk fibroin powder for this purpose, and it was observed that the viscosity of the solution had a significant effect on the membrane fabrication and its properties.

• Journal of Korean Society of Environmental Engineers
• /
• v.36 no.11
• /
• pp.781-790
• /
• 2014

Contaminants such as organic matters, nutrients and toxic chemicals in rivers and lakes with a weak flow rate are first removed from the water and accumulated in the sediments. Subsequently, they are released into the water column again, posing direct/indirect adverse effects on the water quality and aquatic ecosystems. In particular, phosphorus is known to accelerate the eutrophication phenomenon when it is released into the water column via physical disturbance and biological/chemical actions as one of important materials that determine the primary production of aquatic ecosystems and an element that is stored mainly in the sediments in the process of material circulation in the body of water. In this study, the effect on reducing phosphorus release in sediments was analyzed by applying different capping materials to lake water, where the effect of aquatic microorganisms is taken into account, and to distilled water, where the effect of microorganisms is excluded. The experimental results showed that capping with chemical materials such as Fe-gypsum and $SiO_2$-gypsum further reduced the phosphorus release by at least 40% compared to the control case. Composite materials like granule gypsum+Sand showed over 50% phosphorus release reduction effect. Therefore, it is determined that capping with chemical materials such as granule-gypsum and eco-friendly materials such as sand is effective in reducing phosphorus release. The changes in phosphorus properties in the sediments before and after capping treatment showed that gypsum input helped to change the phosphorus that is present in lake sediments into apatite-P, a stable form that makes phosphorus release difficult. Based on the above results, it is expected that the application of capping technology will contribute to improving the efficiency of reducing phosphorus release that occurs in river and lake sediments.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.19 no.3
• /
• pp.180-188
• /
• 1999

The dynamic elastic properties of metal matrix composites were investigated by resonant ultrasound spectroscopy(RUS). The composites used in this study consisted of 2124 aluminum alloy reinforced with different concentrations of SiC particles. RUS can determine the nine independent elastic stiffness($C_{ij}$) for the orthorhombic symmetry on a small specimen simultaneously. The elastic constants were determined as a function of the volume fraction. A concept of effective aspect ratio. which combine the aspect ratio and the orientation of reinforcement. was used to calculate the initial moduli from Mori-Tanaka theory for the input of RUS minimization code. Young's moduli can be obtained from the measured stiffnesses. The results show that the elastic stiffness increases with increment of the particle content. The behavior of elastic stiffness indicates that the particle redistribution induced by the extrusion process enlarges the transversely isotropic symmetry as the fraction of reinforced particles increase. This relationship could be used for determination of the volume fractions of reinforcement as a potential tool of nondestructive material characterization.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.11
• /
• pp.949-956
• /
• 2016

There are a number of effects by solar radiation in many aerospace industrial fields, such as degradation of mechanical properties, sealing effect of sealants or decolorization. Because it takes long time to investigate these effects by using the light of natural state, new methods are developed for accelerating this phenomenon. In this paper, we developed an apparatus to simulate accelerated solar radiation phenomenon selecting irradiation intensity $1,120W/m^2$ as the designed environment. Epoxy polymer as the composite material was chosen and processed by ASTM-D638, a reference for tensile test of polymer and plastic. Total color shift was selected as the test category to evaluate acceleration of the test. We obtained acceleration factors and numerical model from test data and concluded it can shorten test periods by accelerated irradiation intensity of $1,120W/m^2$.

• Composites Research
• /
• v.30 no.1
• /
• pp.46-51
• /
• 2017

Structural battery has been researched extensively to combine the functions of the battery and structure without gravimetric or volumetric increments compared to their individual components. The main idea is to employ carbon fabric as the reinforcement and electrode, glass fabric as the separator, and solid-state electrolyte which can transfer load. However, state-of-the-art solid-state electrolytes do not have sufficient load carrying functionality and exhibiting appropriate ion conductivity simultaneously. Therefore, in this research, a system which has both battery and load carrying capabilities using glass fabric separator and liquid electrolyte was devised and tested to investigate the potential and feasibility of this structural battery system and observe electric properties. It was observed that elongating separator decreased electrical behavior stability. A possible cause of this phenomenon was the elongated glass fabric separator inadequately preventing the penetration of small particles of the cathode material into the anode. This problem was verified additionally by using a commercial separator. The characteristic of the glass fabric and the interface between the electrode and glass fabric needed to be further studied for the realization of such a load carrying structural battery system.

• Journal of the Korean Ceramic Society
• /
• v.39 no.9
• /
• pp.851-856
• /
• 2002

Tribological behavior of plasma-sprayed $Cr_2O_3$-based coatings containing $MoO_3$ at 450$^{\circ}C$ was investigated to understand the influence of $MoO_3$. A reciprocal disc-on-plate type tribo-tester was employed to examine fricition and wear behavior of the specimens. The microstructure and phase composition of the coating was characterized with Transmission Electron Microscopy(TEM). The TEM analysis indicated that $MoO_3$ was dispersed into the grain boundary, resulting in the increase of the hardness and density of the coating. Worn surfaces were investigated by scanning electron microscopy and chemistry of the worn surfaces was analyzed using a X-ray Photoelectron Spectrometer(XPS). The results showed that the friction coefficient of the $MoO_3$-added coatings was lower than that without $MoO_3$ addition. The larger protecting layers were observed at the worn surface of plasma spray coated specimens with $MoO_3$ composition in the protecting layer appears to be more favorable in reducing the friction.