• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.11-15
• /
• 2005

공중발사 방식은 일반적인 지상발사와 비교해 볼 때 많은 장점을 지니고 있다. 그러나 공중발사 로켓의 형상은 모선에 장착 시 많은 제한이 따르기 때문에 여러 해석분야를 통합한 시스템 설계가 필요하다. 시스템 설계는 순차적 최적화와 MDF 기법을 이용하여 수행되었다. 해석 모듈은 임무분석, 단배분, 추진해석, 형상, 중량해석, 공력해석, 궤적해석을 포함한다. 두 가지 기법 중 MDF 기법을 이용하였을 때 더 좋은 결과를 도출하였다. 시스템 최적화 결과 총 중량 1244.91 kg. 위성중량 7.5 kg, 총 길이 6.18m, 지름 0.60 m을 지닌 초음속 공중발사 로켓이 설계되었다.

• 한국항공우주학회지
• /
• 제33권12호
• /
• pp.26-32
• /
• 2005

공중발사 방식은 일반적인 지상발사와 비교해 볼 때 많은 장점을 지니고 있다. 그러나 공중발사 로켓의 형상은 모선에 장착 시 많은 제한이 따르기 때문에 여러 해석분야를 통합한 시스템 설계가 필요하다. 시스템 설계는 순차적 최적화와 MDF 기법을 이용하여 수행되었다. 해석 모듈은 임무분석, 단배분, 추진해석, 형상, 중량해석, 공력해석, 궤적해석을 포함한다. 두 가지 기법 중 MDF 기법을 이용하였을 때 더 좋은 결과를 도출하였다. 시스템 최적화 결과 총 중량 1244.91kg, 위성중량 7.5kg, 총 길이 6.36 m, 지름 0.60m을 지닌 초음속 공중발사 로켓이 설계되었다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.330-339
• /
• 2008

Ground-based interceptors(GBI) comprise a major element of the strategic defense against hostile targets like Intercontinental Ballistic Missiles(ICBM) and reentry vehicles(RV) dispersed from them. An optimum design of the subsystems is required to increase the performance and reliability of these GBI. Propulsion subsystem design and optimization is the motivation for this effort. This paper describes an effort in which an entire GBI missile system, including a multi-stage solid rocket booster, is considered simultaneously in a Genetic Algorithm(GA) performance optimization process. Single goal, constrained optimization is performed. For specified payload and miss distance, time of flight, the most important component in the optimization process is the booster, for its takeoff weight, time of flight, or a combination of the two. The GBI is assumed to be a multistage missile that uses target location data provided by two ground based RF radar sensors and two low earth orbit(LEO) IR sensors. 3Dimensional model is developed for a multistage target with a boost phase acceleration profile that depends on total mass, propellant mass and the specific impulse in the gravity field. The monostatic radar cross section (RCS) data of a three stage ICBM is used. For preliminary design, GBI is assumed to have a fixed initial position from the target launch point and zero launch delay. GBI carries the Kill Vehicle(KV) to an optimal position in space to allow it to complete the intercept. The objective is to design and optimize the propulsion system for the GBI that will fulfill mission requirements and objectives. The KV weight and volume requirements are specified in the problem definition before the optimization is computed. We have considered only continuous design variables, while considering discrete variables as input. Though the number of stages should also be one of the design variables, however, in this paper it is fixed as three. The elite solution from GA is passed on to(Sequential Quadratic Programming) SQP as near optimal guess. The SQP then performs local convergence to identify the minimum mass of the GBI. The performance of the three staged GBI is validated using a ballistic missile intercept scenario modeled in Matlab/SIMULINK.

• International Journal of Aeronautical and Space Sciences
• /
• 제17권3호
• /
• pp.409-422
• /
• 2016

A parametric study based on an unsteady mathematical model of a pyrotechnically actuated device was performed for design optimization. The model simulates time histories for the chamber pressure, temperature, mass transfer and pin motion. It is validated through a comparison with experimentally measured pressure and pin displacement. Parametric analyses were conducted to observe the detailed effects of the design parameters using a validated performance analysis code. The detailed effects of the design variables on the performance were evaluated using the one-at-a-time (OAT) method, while the scatter plot method was used to evaluate relative sensitivity. Finally, the design optimization was conducted by employing a genetic algorithm (GA). Six major design parameters for the GA were chosen based on the results of the sensitivity analysis. A fitness function was suggested, which included the following targets: minimum explosive mass for the uniform ignition (small deviation), light casing weight, short operational time, allowable pyrotechnic shock force and finally the designated pin kinetic energy. The propellant mass and cross-sectional area were the first and the second most sensitive parameters, which significantly affected the pin's kinetic energy. Even though the peak chamber pressure decreased, the pin kinetic energy maintained its designated value because the widened pin cross-sectional area induced enough force at low pressure.

• Wind and Structures
• /
• 제30권4호
• /
• pp.379-392
• /
• 2020

The paper presents a Life-Cycle Cost-based optimization framework for wind-excited tall buildings equipped with Tuned Mass Dampers (TMDs). The objective is to minimize the Life-Cycle Cost that comprises initial costs of the structure, the control system and costs related to repair, maintenance and downtime over the building's lifetime. The integrated optimization of structural sections and mass ratio of the TMDs is carried out, leading to a set of Pareto optimal solutions. The main advantage of the proposed methodology is that, differently from the traditional optimal design approach, it allows to perform the unified design of both the structure and the control system in a Life Cycle Cost Analysis framework. The procedure quantifies wind-induced losses, related to structural and nonstructural damage, considering the stochastic nature of the loads (wind velocity and direction), the specificity of the structural modeling (e.g., non-shear-type vibration modes and torsional effects) and the presence of the TMDs. Both serviceability and ultimate limit states related to the structure and the TMDs' damage are adopted for the computation of repair costs. The application to a case study tall building allows to demonstrate the efficiency of the procedure for the integrated design of the structure and the control system.

• 한국군사과학기술학회지
• /
• 제19권1호
• /
• pp.95-104
• /
• 2016

To make a firing table of artillery with trajectory simulation, a precise trajectory model which corresponds with real firing test is required. Recent 4-DOF modified point mass trajectory model is considered accurate as a theoretical model, but fitting coefficients are used in calculation to match with real firing test results. In this paper, modified point mass trajectory model is presented and method of setting ballistic coefficient is introduced by applying optimization algorithms. After comparing two different algorithms, Particle Swarm Optimization and Covariance Matrix Adaptation - Evolutionary Strategy, we found that using CMA-ES algorithm gives fine optimization result. This fitting coefficient setting method can be used to make trajectory simulation which is required for development of new projectiles in the future.

• Structural Engineering and Mechanics
• /
• 제58권2호
• /
• pp.301-326
• /
• 2016

An optimization method of patch shape was developed in this study, in order to improve repair of cracked plates. It aimed to minimize three objectives: stress intensity factor, patch volume and shear stresses in the adhesive film. The choice of these objectives ensures improving crack repair, gaining mass and enhancing the adhesion durability between the fractured plate and the composite patch. This was a multi-objective optimization combined with Finite elements calculations to find out the best distribution of patch height with respect to its width. The implementation of the method identified families of optimal shapes with specific geometric features around the crack tip and at the horizontal end of the patch. Considerable mass gain was achieved while improving the repair efficiency and keeping the adhesive shear stress at low levels.

• 한국안전학회지
• /
• 제13권1호
• /
• pp.40-46
• /
• 1998

This paper is presented that theoretical optimization design method in order to consider mass reduction for the structural safety In this paper, it described methods for reducing vibration in structural safety by the determination of the optimum sizes and locations of tunning masses through formal mathematical optimization techniques. The optimization procedure which employs the tunning masses and corresponding locations is developed. Design variables are systematically changed to achieve low values of shear without a large mass penalty. Three optimization methods ire developed and tested. The first is based on minimizing the modal shaping parameter which indirectly reduce the modal shear amplitudes corresponding to each harmonic of airload. The second method reduces these amplitudes directly and the third method reduces the shear as a function of time during a revolution of the blade. The first method works well for reducing the shear for one mode responding to a single harmonic of the airload but has been found in some bases to be ineffective for more than one mode.

• Earthquakes and Structures
• /
• 제7권6호
• /
• pp.1071-1091
• /
• 2014

Pounding of adjacent structures are always a notable reason for damages after strong ground motions, but it is already unforeseen detail in newly constructed structures. Thus, several approaches have been proposed in order to prevent the pounding of structures. By using optimally tuned mass dampers, it is possible to decrease the displacement vibrations of structures. But in adjacent structures, the response of both structures must be considered in the objective function of optimization process. In this paper, two different designs of Tuned Mass Dampers (TMD) are investigated. The first design covers independent TMDs on both structures. In the second design, adjacent structures are coupled by a TMD on the top of the structures. Optimum TMD parameters are found by using the developed optimization methodology employing harmony search algorithm. The proposed method is presented with single degree of freedom and multiple degree of freedom structures. Results show that the coupled design is not effective on multiple degree of freedom adjacent structures. The coupled design is only effective for rigid structures with a single degree of freedom while the use of independent TMDs are effective on both rigid and flexural structures.

• 한국음향학회지
• /
• 제40권1호
• /
• pp.64-72
• /
• 2021

본 논문에서는 유체의 이동에 의한 배관의 진동을 저감시키기 위해 동조질량감쇠기(Tuned Mass Damper, TMD)의 최적 설계를 수행하였다. 배관 설비의 정확한 진원과 배관의 사양을 알지 못하는 상황에서 TMD 설계를 하기 위해 MATLAB을 이용하여 배관시스템 모델을 설계하고, 이를 바탕으로 최적 설계 방법을 개발하였다. 개발된 최적화 방법은 ANSYS Workbench에서 유한요소 모델을 이용해 최적 설계 방법을 검증했다. 그리고 실제 배관 시스템의 측정값을 바탕으로 진동수를 보정할 수 있도록 TMD를 설계 및 제작하고 실제 배관 시스템에 설치해 감쇠 진폭이 95% 수준으로 줄어든 것을 확인했다.