• 한국항공우주학회지
• /
• 제44권10호
• /
• pp.887-894
• /
• 2016

고상-액상 상변화물질(PCM, Phase Change Material)을 이용한 위성부품 열제어장치를 설계 및 제작하였으며 열환경시험을 수행함으로써 온도제어 성능을 분석하였다. 설계온도에 부합하는 n-Hexadecane을 PCM으로 채용하였고, 낮은 열전도도를 보완하기 위하여 내부에 전열휜이 장착된 용기를 Al6061로 제작하였다. 위성에 장착하였을 때와 동일한 작동조건을 확보하기 위하여, 부품과 방열판 사이를 열관으로 연결하였으며 열관의 단열부가 관통하도록 PCM 열제어장치를 설치하였다. 동일한 모양과 부피의 열적완충질량(TBM, Thermal Buffer Mass)도 제작하여, 주기적인 가열-냉각 실험을 수행하였다. 실험결과 상변화 잠열에 의한 PCM의 열제어 성능을 확인할 수 있었으며, TBM에 비하여 질량과 보온히터의 소모전력을 절감할 수 있음을 확인하였다.

• International Journal of Automotive Technology
• /
• 제8권6호
• /
• pp.761-769
• /
• 2007

The configuration of the flow channel on a bipolar plate of a proton exchange membrane fuel cell(PEMFC) for efficient reactant supply has great influence on the performance of the fuel cell. Recent demand for higher energy density fuel cells requires an increase in current density at mid voltage range and a decrease in concentration overvoltage at high current density. Therefore, an interdigitated flow channel where mass transfer rate by convection through a gas diffusion layer is greater than the mass transfer by a diffusion mechanism through a gas diffusion layer was recently proposed. This study attempts to analyze the i-V performance, mass transfer and pressure drop in interdigitated flow channels by developing a fully three dimensional simulation model for PEMFC that can deal with anode and cathode flow together. The results indicate that the trade off between performance and pressure loss should be considered for efficient design of flow channels. Although the performance of the fuel cell with interdigitated flow is better than that with conventional flow channels due to a strong mass transfer rate by convection across a gas diffusion layer, there is also an increase in friction due to the strong convection through the porous diffusion layer accompanied by a larger pressure drop along the flow channel. It was evident that the proper selection of the ratio of channel and rib width under counter flow conditions in the fuel cell with interdigitated flow are necessary to optimize the interdigitated flow field design.

• Wind and Structures
• /
• 제10권1호
• /
• pp.1-22
• /
• 2007

The suppression of aerodynamic response of long-span suspension bridges during erection and after completion by using single TMD and multi TMD is presented in this paper. An advanced finite-element-based aerodynamic model that can be used to analyze both flutter instability and buffeting response in the time domain is also proposed. The frequency-dependent flutter derivatives are transferred into a time-dependent rational function, through which the coupling effects of three-dimensional aerodynamic motions under gusty winds can be accurately considered. The modal damping of a structure-TMD system is analyzed by the state-space approach. The numerical examples are performed on the Akashi Kaikyo Bridge with a main span of 1990 m. The bridge is idealized by a three-dimensional finite-element model consisting of 681 nodes. The results show that when the wind velocity is low, about 20 m/s, the multi TMD type 1 (the vertical and horizontal TMD with 1% mass ratio in each direction together with the torsional TMD with ratio of 1% mass moment of inertia) can significantly reduce the buffeting response in vertical, horizontal and torsional directions by 8.6-13%. When the wind velocity increases to 40 m/s, the control efficiency of a multi TMD in reducing the torsional buffeting response increases greatly to 28%. However, its control efficiency in the vertical and horizontal directions reduces. The results also indicate that the critical wind velocity for flutter instability during erection is significantly lower than that of the completed bridge. By pylon-to-midspan configuration, the minimum critical wind velocity of 57.70 m/s occurs at stage of 85% deck completion.

• Journal of Ginseng Research
• /
• 제44권6호
• /
• pp.775-783
• /
• 2020

Background: The reports about valuable oligosaccharides in ginseng are quite limited. There is an urgent need to develop a practical procedure to detect and analyze ginseng oligosaccharides. Methods: The oligosaccharide extracts from ginseng were permethylated by solid-phase methylation method and then were analyzed by ultra-high-performance liquid chromatography-Q-Orbitrap/MS. The sequence, linkage, and configuration information of oligosaccharides were determined by using accurate m/z value and tandem mass information. Several standard references were used to further confirm the identification. The oligosaccharide composition in white ginseng and red ginseng was compared using a multivariate statistical analysis method. Results: The nonreducing oligosaccharide erlose among 12 oligosaccharides identified was reported for the first time in ginseng. In the comparison of the oligosaccharide extracts from white ginseng and red ginseng, a clear separation was observed in the partial least squares-discriminate analysis score plot, indicating the sugar differences in these two kinds of ginseng samples. The glycans with variable importance in the projection value large than 1.0 were considered to contribute most to the classification. The contents of oligosaccharides in red ginseng were lower than those in white ginseng, and the contents of maltose, maltotriose, maltotetraose, maltopentaose, maltohexaose, maltoheptaose, maltooctaose, maltononaose, sucrose, and erlose decreased significantly (p < 0.05) in red ginseng. Conclusion: A solid-phase methylation method combined with liquid chromatography-tandem mass spectrometry was successfully applied to analyze the oligosaccharides in ginseng extracts, which provides the possibility for holistic evaluation of ginseng oligosaccharides. The comparison of oligosaccharide composition of white ginseng and red ginseng could help understand the differences in pharmacological activities between these two kinds of ginseng samples from the perspective of glycans.

• 한국안전학회지
• /
• 제32권2호
• /
• pp.92-97
• /
• 2017

This study deals with new application method of the connecting tuned mass damper (CTMD) system for efficient vibration control of adjacent twin structures which have the same dynamic properties such as natural frequency and damping characteristics to each other. In the existing research, the vibration control of the twin structures has a limit to the application of the conventional damper-connection method of the twin structures. Due to the same frequency characteristics leading to the equally vibrating behaviors, it is impossible to apply the conventional connection method of the adjacent structures. In order to overcome these limitations induced by the symmetry of the dynamic characteristics, we propose a new CTMD-based control system that adopts the conventional connection configuration but unbalances the symmetric system by arranging the control device asymmetrically and then can finally achieve the efficient control performance. In order to demonstrate the applicability of the proposed system, numerical simulations of the optimally designed proposed system have been performed in comparison with the optimal design results of the existing independent single tuned mass damper (STMD) control system and the another optimal control system previously proposed by the same author, hereafter called CTMD-OsTMD. The comparative results of the control performances among STMD, CTMD-OsTMD and the proposed CTMD systems verified that the newly proposed control system can be a control-efficient and cost-effective system for vibration suppression of the two adjacent twin structures.

• Smart Structures and Systems
• /
• 제22권6호
• /
• pp.727-741
• /
• 2018

To mitigate vibrations, tuned mass dampers(TMD) are widely used for long span bridges or high-rise buildings. Due to some durability concerns, such as fluid degradation, oil leakage, etc., the alternative solutions, such as the non-contacted eddy current damping (ECD), are proposed for mechanical devices in small scales. In the present study, a new eddy current damping TMD (ECD-TMD) is proposed and developed for large scale civil infrastructure applications. Starting from parametric study on finite element analysis of the ECD-TMD, the new design is enhanced via using the permanent magnets to eliminate the power need and a combination of a copper plate and a steel plate to improve the energy dissipation efficiency. Additional special design includes installation of two permanent magnets at the same side above the copper plate to easily adjust the gap as well as the damping. In a case study, the proposed ECD-TMD is demonstrated in the application of a steel arch bridge to mitigate the wind-induced vibrations of the flexible hangers. After a brief introduction of the configuration and the installation process for the damper, the mitigation effects are measured for the ambient vibration and forced vibration scenarios. The results show that the damping ratios increase to 3% for the weak axis after the installation of the ECD-TMDs and the maximum vibration amplitudes can be reduced by 60%.

• 한국정보통신학회:학술대회논문집
• /
• 한국정보통신학회 2015년도 추계학술대회
• /
• pp.436-438
• /
• 2015

본 논문에서는 사물인터넷 게이트웨이 간의 직접통신 서비스를 제공하기 위해서 와이파이 다이렉트의 P2P Standard Group Formation(P2P-SGF)을 구현한다. 일반적으로 AP(Access Point)를 통해 사물인터넷 게이트웨이 간에 여러 센서들로부터 수집된 데이터와 더불어 대용량 데이터를 전송할 경우 네트워크 트래픽 혼잡 문제와 속도저하 문제가 발생한다. 이러한 문제를 해결하기 위해서 AP를 거치지 않고 사물인터넷 게이트웨이 간에 직접통신으로 대용량 데이터를 효율적으로 전송할 수 있는 와이파이 다이렉트 구현이 필요하다. 논문에서 구현한 P2P-SGF는 기본적으로 Discovery, GO(Group Owner) Negotiation, WPS(WiFi Protected Setup) Provisioning, Address Configuration을 수행하며, 특히 대용량 데이터를 공유하기 위해 DLNA(Digital Living Network Alliance) 서비스 기능을 지원한다. 구현한 P2P-SGF를 통해 대용량의 동영상이 성공적으로 공유되는 것을 실험실 테스트로 확인하였다.

• 정보관리연구
• /
• 제20권2호
• /
• pp.69-99
• /
• 1989

본연구(本硏究)는 레이저기술(技術)과 정보공학(情報工學)의 눈부신 발전과정(發展過程)에서 등장한 대용량 정보축적매체(情報蓄積媒體)인 CD-ROM Catalog Production Product 중에서 BiblioFile을 선택하고, CD-ROM BiblioFile과 과학기술대학도서관(料學技術大學圖書館)에서 자체 개발(開發)한 시스템인 KITLAS를 시스템구성(構成), 파일구조(構造), 특성(特性) 및 기능면(機能面)에서 비교분석(比較分析)한 후 CD-ROM에 수록(收錄)된 MARC 레코드의 변환(變換)과 온라인 대량, 동시 전송(傳送)하는 과정(過程)인 이른바 다운로드(download)와 업로드(up-load)하는 과정(過程)을 구현하여 서지정보(書誌情報) 데이터베이스의 신뢰성(信賴性) 향상(向上) 방법(方法)을 모색하였다.

• Journal of Chest Surgery
• /
• 제13권3호
• /
• pp.274-279
• /
• 1980

A 21 years old male student was admitted because of mediastinal mass that was noticed in routine physical examination. He complained progressive hoarseness, mild dysphagia, and anterior chest pain on deep respiration. This mediastinal mass was diagnosed as aortic aneurysm involving ascending, transverse, and descending thoracic aorta with aid of aortogram. Total prosthetic replacement of aneurysm was performed successfully using extracorporeal circulation and hypothermia. For myocardial protection during aortic cross clamping, cardioplegic solution was used and topical myocardial cooling was also adapted For simplicity of cardiopulmonary bypass, Y-shaped connectors took cerebral perfusion catheters to the main perfusion line beyond the arterial pump. Total bypass time was 219 minutes, and aortic cross clamp time was 104 minutes. Recovery was uneventful except respiratory insufficiency for first 4 days. Isotope aortogram checked on post operative 30th day showed normal aortic configuration. He was discharged on post operative 35th day. A follow-up chest X-ray study 5 months later showed nearly normal anatomy.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2005년도 제24회 춘계학술대회논문집
• /
• pp.11-15
• /
• 2005

공중발사 방식은 일반적인 지상발사와 비교해 볼 때 많은 장점을 지니고 있다. 그러나 공중발사 로켓의 형상은 모선에 장착 시 많은 제한이 따르기 때문에 여러 해석분야를 통합한 시스템 설계가 필요하다. 시스템 설계는 순차적 최적화와 MDF 기법을 이용하여 수행되었다. 해석 모듈은 임무분석, 단배분, 추진해석, 형상, 중량해석, 공력해석, 궤적해석을 포함한다. 두 가지 기법 중 MDF 기법을 이용하였을 때 더 좋은 결과를 도출하였다. 시스템 최적화 결과 총 중량 1244.91 kg. 위성중량 7.5 kg, 총 길이 6.18m, 지름 0.60 m을 지닌 초음속 공중발사 로켓이 설계되었다.