• Journal of the Korean institute of surface engineering
• /
• v.37 no.4
• /
• pp.234-241
• /
• 2004

Cavitation erosion properties of the Cu-9Al-4.5Ni-4.5Fe alloys (Al-bronze) surface-modified by flame quenching process have been investigated. After flame quenching at above $T_{\beta}$, the surfaces of Al-bronze with $\alpha$ + $\textsc{k}$ structure have been changed into the $\alpha$ + $\beta$' martensite phases by the eutectoid reaction of $\alpha$ + $\textsc{k}$\longrightarrow$\beta$ followed by the martensite transformation of $\beta$\longrightarrow$\beta$'. As a result of cavitation test, the measured incubation time and erosion rate of the $\alpha$ + $\beta$' alloy was 1.2 times higher and 1.5 times lower, respectively, compared to those of the conventional $\alpha$ + $\textsc{k}$ alloys, showing a remarkable increase of cavitation resistance with the formation of $\beta$' martensite. This is attributed to a preferential erosion of the $\textsc{k}$ precipitates that show the lowest resistance among the $\alpha$, $\textsc{k}$, $\beta$' phases under cavitation loading.ases under cavitation loading.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.407-408
• /
• 2006

Dimensional precision is a critical parameter in net shape processing of ferrous PM components. Sinter-hardening alloys undergo a transformation from austenite to martensite. Martensite formation expands the sintered compact, while tempering hardened steels results in shrinkage. In addition, martensitic regions with high Cu and C contents may contain large amounts of retained austenite. The presence of martensite and retained austenite, in addition to the tempering step, all play a role in the final dimensions of a component. This paper investigates the dimensional and microstructural changes to two sinter-hardening grades through different post-sintering thermal treatments.

• Journal of the Korean Society for Heat Treatment
• /
• v.21 no.2
• /
• pp.69-78
• /
• 2008

Differences in hardness and microstructure between surface and area at 0.3 mm below the surface after quenching and tempering of ductile cast iron for rear planet carrier of automotive transmission have been investigated. Microstructure of ductile cast iron consisted of ferrite, pearlite, and nodular graphite. The amount of pearlite increased with going down to the half-thickness area. It was found that Cr and Mo segregated to the pearlite and the pearlite transformed to the harder martensite during quenching. The martensite was more resistant to the decomposition to ferrite and cementite during tempering because of segregation of Cr and Mo, resulting in the harder tempered martensite. Consequently, the hardness of the surface with less amount of pearlite, corresponding to the harder martensite in the quenched and tempered microstructure, was lower than that of the area at 0.3 mm below the surface.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.7 no.4
• /
• pp.372-378
• /
• 1983

Use of dual phase steel are growing for its high strength and light weight in automobiles. The effect of the martensite volume fraction with various impact velocities on the strength, ductility and absorbed energy of dual phase (ferrite-martensite) steels were investigated in low carbon 1.5% Mn steels which were soaked at 700.deg. C, 730.deg. C, 780.deg. C, and brine quenched. Both the yield load and the maximum impact load increased when the martensite volume fraction increased, the loading time and the absorbed energy of the specimen decreased when the martensite volume fraction increased.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.533-538
• /
• 2000

Ductile fracture of dual phase steel begins with void nucleation, at martensite-ferrite interface of deformed martensite particle. In this study, void nucleation, growth, and coalescence under various strain were studied in dual phase steel. Therefore, by means of the heat treatment of low carbon steel, the study deals with void nucleation and growth for ferrite grain size and martensite volume fraction of dual phase steel using statistical method. Void nucleation and growth with increasing strain are shown depend upon the ferrite grain size. Voids volume fraction generally increase as ferrite grain size decease.

• Journal of Power System Engineering
• /
• v.14 no.2
• /
• pp.78-83
• /
• 2010

This study was carried out to investigate the effect of microstructure on the damping capacity of 12Cr martensite heat-resisting steels, in case of the specimen with martensite phase contained the volume faction of ferrite phases, under 5%. The damping capacity was decreased with the increase of solution treatment temperature and time. While it was increased with the increase of tempering temperature and time. The damping capacity was higher in case of specimen with martensite single phase structure than the specimen with martensite phase contained of ferrite phases.

• Journal of Power System Engineering
• /
• v.18 no.3
• /
• pp.100-105
• /
• 2014

This study is to investigate the effect of thermo mechanical treatment on the mechanical properties of 316L stainless steel. ${\alpha}^{\prime}$ and ${\varepsilon}$-martensite was formed by deformation. With increasing number of thermo mechanical treatment, volume fraction of martensite was increased rapidly, and then unchanged. With increasing number of thermo mechanical treatment, hardness and strength was increased rapidly, and then unchanged while elongation was decreased rapidly, and then unchanged. With increasing volume fraction of martensite formed by thermo mechanical treatment, hardness and strength was increased rapidly, elongation was decreased rapidly. Thus, hardness, strength and elongation of thermo mechanical treated 316L stainless steel was strongly affected by martensite formed by thermo mechanical treatment. Good combination of strength and elongation was obtained from thermomechanical treatment.

• Journal of the Korean Society for Heat Treatment
• /
• v.10 no.3
• /
• pp.188-197
• /
• 1997

Effect of martensite morphology on damping capacity and hardness of Fe-Ni-C martensitic alloys were studied. The morphologies of martensite such as lath, butterfly, lenticular and thin plate were prepared by adjusting nickel content and austenite grain size. The hardness increased in order of lath, lenticular, thin plate, butterfly. The damping capacities of the lath and butterfly martensites were higher than those of the other two morphologies, indicating that the dislocation substructure is more effective in the damping capacity than the twin substructure. Especially, the butterfly martensite showed the highest damping capacity among these morphologies because of presence of not tangled but free dislocations in there.

• Journal of the Korean Society for Heat Treatment
• /
• v.17 no.6
• /
• pp.342-345
• /
• 2004

In this work, a new method of measuring volume fraction of deformation-induced ${\varepsilon}$ martensite is proposed using endothermic heat on reverse transformation. As grain size increases, the amount of ${\varepsilon}$ martensite forming on cooling increases. However, with a decrease in grain size, more ${\varepsilon}$ is induced by deformation, improving shape memory effect.

• Journal of Korea Foundry Society
• /
• v.19 no.1
• /
• pp.84-90
• /
• 1999

In this study, CV cast iron was reverse transformed to produce harder second phase surrounding graphite nodules, and then the microstructure and related mechanical properties of the reverse transformed CV cast iron were investigated by using optical microscopy and by carrying out hardness, tension and impact test. The formation of hard second phase surrounding graphite nodules increased the hardness in CV cast iron. The marked increase in hardness was resulted from the formation of martensite surrounding graphite nodule. It is expected from these results that the formation of martensite surrounding graphite nodule would improve the wear resistance of CV cast iron. The formation of both martensite and pearlite surrounding graphite nodule improved the tensile properties. Impact properties were decreased with increasing the volume fraction of hard second phase. However, the reduced impact properties could be recovered through phase transformation of martensite into pearlite and sorbite by tempering.