• Smart Structures and Systems
• /
• 제14권5호
• /
• pp.869-881
• /
• 2014

This paper presents the materials analysis for combination of working modes of Magnetorheological (MR) damper. The materials were selected based on the optimum magnetic field strength at the effective areas in order to obtain a better design of MR damper. The design of electromagnetic circuit is one of the critical criteria in designing MR dampers besides the working mechanism and the types of MR damper. The increase in the magnetic field strength is an indication of the improvement in the damping performance of the MR damper. Eventually, the experimental test was performed under quasi-static loading to observe the performances of MR damper in shear mode, squeeze mode and mixed mode. The results showed that the increment of forces was obtained with the increased current due to higher magnetic flux density generated by electromagnetic coils. In general, it can be summarized that the combination of modes generates higher forces than single mode for the same experimental parameters throughout the study.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제53권4호
• /
• pp.229-236
• /
• 2004

In this paper, the effect of permanent magnet overhang structure on the characteristics in Brushless DC motor has analyzed quantitatively. We classified the overhang structure as symmetric and asymmetric. 3D equivalent magnetic circuit network (EMCN) method which uses the permeance as the distributive variable is used for the efficient analysis of magnetic field. The overhang effect which increases the linkage flux at the stator is verified by comparison between overhang and no overhang structure. In addition, it is known that no load back electro motive force (EMF) is also increased due to the overhang effect. In case of asymmetric overhang structure, the ratio effect of the upper to lower overhang length on the magnetic forces is analyzed. Form the analysis results, the variation of the asymmetric overhang ratio has a significant effect on the axial magnetic force except the radial and tangential magnetic forces. The validity of the analysis results is also clarified by comparison between calculated results and measured ones such as back EMF and cogging torque.

• Advances in nano research
• /
• 제10권5호
• /
• pp.481-491
• /
• 2021

Graphene Nanosheets play an important role in nanosensors due to their proper surface to volume ratio. Therefore, the main purpose of this paper is to consider the nonlinear vibration behavior of graphene nanosheets (GSs) under the influence of electromagnetic fields and electrical current create forces. Considering more realistic assumptions, new equations have been proposed to study the nonlinear vibration behavior of the GSs carrying electrical current and placed in magnetic field. For this purpose, considering the influences of the magnetic tractions created by electrical and eddy currents, new relationships for electromagnetic interaction forces with these nanosheets have been proposed. Nonlinear coupled equations are discretized by Galerkin method, and then solved via Runge-Kutta method. The effect of different parameters such as size effect, electrical current magnitude and magnetic field intensity on the vibration characteristics of GSs is investigated. The results show that the magnetic field increases the linear natural frequency, and decreases the nonlinear natural frequency of the GSs. Excessive increase of the magnetic field causes instability in the GSs.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 추계학술대회논문초록집
• /
• pp.342.2-342
• /
• 2002

Fault tolerant control algorithm fer heteropolar magnetic bearings are presented. This fault tolerant control utilizes grouping of currents as C-cores in order to isolate magnetic fluxes. Hardware requirements to maintain fault tolerant control are reduced since decoupling chokes are not required in this control scheme. The currents supplied to each pole are redistributed, if some coils (ail suddenly, such that the resultant magnetic forces should remain invariant through coil failure events. (omitted)

• 한국정밀공학회지
• /
• 제29권8호
• /
• pp.873-878
• /
• 2012

Putting a conductive rod between rotating axial electrodynamic wheels composed of repetitive permanent magnets, three-axial magnetic forces generate on the conductive rod. It is possible to levitate and transfer the rod on space with the forces. However, the forces vary in direction and magnitude for a position of the rod between the electrodynamic wheels. Thus, the position influences the stability of the rod also. To guarantee the stability of a levitated object, the force acting on the object should have negative stiffness like a spring. So, we analyze the stable operating range of the conductive rod levitated by the axial wheels with the commercial finite element tool in this paper. Specially, as the pole number and the radial width of permanent magnets has much influence on the generated force and thereby the stable region, their sensitivities are analyzed also. The analytic result is compared with experimental result.

• Nuclear Engineering and Technology
• /
• 제30권1호
• /
• pp.17-25
• /
• 1998

Transport of carbon and boron impurity ions parallel to magnetic field lines in the tokamak SOL (scrape-off layer) is numerically investigated for a one-dimensional steady state. The spatial distributions of density and velocity of the impurity ions in a steady state are calculated by finite difference method for a single-fluid model. The calculated results show that among forces acting on SOL particles thermal force produced tv plasma temperature gradient is a principal force determining the feature of impurity distribution profiles in the tokamak edge. However, strong collisional friction forces appearing dominant in front of the diverter plate restrain impurity ion flows due to temperature gradients from moving toward the midplane. Consequently, the stagnation point develops in the impurity flow by these two forces near the diverter region, in which ion flows change their directions. Impurity ions turn out to be accumulated at the stagnation points, where peaked profiles of highly-ionized state ions are relatively predominant over those of low-ionized state ions.

• Journal of Electrical Engineering and Technology
• /
• 제6권3호
• /
• pp.356-363
• /
• 2011

Vibrations and noise in electrical machines are directly related to the characteristics of the radial forces on one hand, and mechanical behavior on the other [1, 4]. The characteristics of these forces depend on the air gap flux density, which is also influenced by other factors, such as stator slots and poles, saturation level, winding type, and certain faults. The aim of this work is to investigate the effect of eccentricity and demagnetization faults on electromagnetic noise generated by the external surface of Permanent Magnet Synchronous Machine [PMSM]. For this purpose, an analytical electromagnetic vibroacoustic model is developed. The results confirm the effect of eccentricity and demagnetization fault in generating some low modes radial forces.

• 대한치과보철학회지
• /
• 제29권2호
• /
• pp.49-57
• /
• 1991

The magnets were widely used to increase the retention of overdentures. The purpose of this study was to compare the break load between overdentures and edentulous models. For this study, Model former(U-402) was used for model fabrication and four different magnets were used for evaluation of break load. The artificial saliva was used between overdenture and model. Breakaway loads were tested with an Instron 1122 at a speed of 2mm/min. The results were as follows. 1. The retentivee forces complete dentures with artificial saliva were than the retentive forces of complete detures without artificial saliva. 2. Magnetic overdenture with artificial saliva showed best retentive force, magnetic overdenture without artificial saliva showed the next retentive force, and the complete denture without artificial saliva showed the worst retention. 3. As the magnetic sizes increased, the retentive forces of magnetics were increased. 4. The retentive force of nipple shape magnet is greater than the retentive force of flate shape magnet in the same size.

• KEPCO Journal on Electric Power and Energy
• /
• 제2권3호
• /
• pp.383-389
• /
• 2016

국내 154 kV 복도체 가공송전선로를 대상으로 전자력에 의한 소도체간 접촉현상을 실증적으로 재현하고 대처 방안을 제시하였다. 도체에 흐르는 전류의 크기가 클수록, 스페이서의 간격이 클수록 소도체간에 작용하는 전자력은 크게 측정되었다. 스페이서 간격이 68 m일 경우 전류 크기가 2,000 A 일 때부터 소도체는 불안정한 상태가 되어 소도체간 간격이 변화하는 횡방향 진동이 시작되었다. 스페이서 간격이 136 m일 경우 전류 크기가 증가할수록 소도체간 간격은 좁아지다가 2,250 A 일 때 두 소도체는 완전히 접촉하였다. 스페이서 간격에 따른 전자력의 크기를 도식화하고 안전한 스페이서 간격을 제시하였다. 시험선로와 실선로 간에는 접촉현상이 발생하는 조건이 상이한 것으로 나타났으며, 이는 송전선로 가선 과정에서 도체에 가해진 여러 형태의 잔류 응력, 바람 조건 등의 차이 때문으로 판단되었다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1989년도 추계학술대회 논문집 학회본부
• /
• pp.87-90
• /
• 1989

The force acting on high Tc superconductors at 77K is measured and analyzed numerically. Both values are compared, and the difference between them is discussed. The forces, acting on a superconducting disk (thickness:1[mm], diameter:12[mm]) in an axially-symmetric magnetic field produced by a solenoid or a permanent magnet ring, are measured at 77K. The disk is an YBCO high Tc superconductor. The discrete surface current method(DSCM) is formalized for an axially-symmetric magnetic field. The forces of the superconducting disk in the magnetic field are analyzed using the DSCM, assuming that the disk is a perfect diamagnetic body. When the bottom side of the disk is separated 8[mm] from the top side of the solenoid, and the magnetic field applied on the center of the bottom side of the disk is 96[G], the measured value and the calculated value of the force are 96 and 496[mgf], respectively. The difference between them is caused by a non-perfect diamagnetism of the high Tc superconductor at 77K. It is proposed that a real force acting on high Tc superconductors at 77K can be estimated on the basis of a measured magnetic susceptibility of the high Tc superconductor at 77K and a calculated force of a perfect diamagnetic body.