• Journal of Institute of Convergence Technology
• /
• v.5 no.2
• /
• pp.7-12
• /
• 2015

A novel topology for the magnet gear is proposed in this study. Differently from the existing methods, both sides of magnet array in this topology are used, resulting in increasing the efficiency of the mechanism. The closed magnetic path between the magnetic elements decreases the leakage flux, so the interlinking magnetic flux through the air-gap is focused and intensified. This paper discusses the dominant parameters of the proposed magnet gear influencing the resulting transmission torque. The parameters are designed from the sensitivity analysis using the commercial FEM analysis tool. And, the test setup for verifying the performance of the system is described.

• Journal of Power Electronics
• /
• v.3 no.1
• /
• pp.55-61
• /
• 2003

This paper presents parameter measurement for permanent magnet synchronous motors based on the P-Q circle diagram. Three electrical parameters of permanent magnet synchronous motors, i.e., the equivalent iron loss resistance, armature inductance, and electrical motive force (emf) coefficient are simultaneously measured. The advantages of this method are that it can be implemented under constant excitation and it dispenses with the generating test for the emf coefficient. The proposed method is applied to a 160w permanent magnet synchronous motor, and then the measurement results are analyzed.

• Journal of Magnetics
• /
• v.21 no.2
• /
• pp.249-254
• /
• 2016

Recently, electric vehicles have got significant attention because it is more eco-friendly and efficient than internal combustion engine vehicles. Instead of an internal combustion engine, the electric vehicle has a motor for propulsion. The permanent magnet synchronous motor which has permanent magnet instead of field winding in the rotor has especially higher efficiency and power density than other types of motor. When the irreversible demagnetization is occurred, drivers are exposed to high risk of accident by the fault operation of motor. Therefore, the irreversible demagnetization of permanent magnet should be detected to reduce the risk of accident. In this study, the demagnetization diagnosis method based on the result of locked rotor test is proposed. Based on short measurement time, the proposed diagnosis method aims to detect the demagnetization fault when an electric vehicle is at a complete standstill. The proposed method is verified through the finite element analysis.

• KIEE International Transactions on Electrophysics and Applications
• /
• v.3C no.1
• /
• pp.1-4
• /
• 2003

This paper presents an attempt to develop probabilistic multistress life models to evaluate the lifetime characteristics of epoxy-encapsulated magnet wire with heavy build polyurethane enamel. A set of accelerated life tests were conducted over a wide range of pulsating voltages, temperatures, and frequencies. Samples of fine gauge twisted pairs of the encapsulated magnet wire were tested us-ing a pulse endurance dielectric test system. An electrical-thermal lifetime function was combined with the Weibull distribution of lifetimes. The parameters of the combined Weibull-electrical-thermal model were estimated using maximum likelihood estimation. Likewise, a generalized electrical-thermal-frequency life model was also developed. The parameters of this new model were estimated using multiple linear regression technique. It was found in this paper that lifetime estimates of the two proposed probabilistic multistress life models are good enough. This suggests the suitability of using the general electrical-thermal-frequency model to estimate the lifetime of the encapsulated magnet wire over a wide range of voltages, temperatures and pulsating frequencies.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.28 no.5
• /
• pp.39-51
• /
• 2014

This paper deals with design of a direct-coupled, small-scaled permanent magnet generator (PMG) for wind power application. First, this paper determines rated power and speed of the PMG from measured characteristics of wind turbines. Second, we derive analytical solutions for the open-circuit field in order to determine optimum magnet thickness and pole pitch/arc ratio. Third, on the basis of open circuit field solutions, stator magnetic circuit including slot opening, teeth width and yoke thickness is designed. And then, a diameter of stator coil which agree with a required current density is calculated, and its turns are determined from the area of slot considering winding packing factor. Finally, finite element (FE) method is employed in analyzing the details of the designed PMG and, test results such as back-emf measurements are given to confirm the design.

• Proceedings of the KIEE Conference
• /
• 1996.07a
• /
• pp.86-88
• /
• 1996

Using superconducting magnetic flux pump, thick power leads for a superconducting magnet could be replaced with thin string leads for the excitation magnet to the superconducting flux pump. We have developed a new type flux pump with high voltage output to shorten the charge and discharge time of the load magnet. The test of four stacked disks as the excither for the load magnet has been carried out. This disk type flux pump yielded 70 mV of voltage across its terminal and 10 A of current through 85 mH load magnet which was the field winding of 20 kVA class fully superconducting generator within 12 seconds. This output voltage of the new superconducting flux pump is about 10 times larger than that of the previous work Moreover since it is easy to stack the disks for the superconduction flux pump, the high voltage exciter for the 1H class superconducting magnet would be expected to be made easily.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2002.02a
• /
• pp.374-377
• /
• 2002

Magnetic field is necessary to control the convection of melted silicon and to improve the quality of the wafer in the 12inch silicon wafer growing process. Nowadays, superconducting magnet is used in this process. We fabricated and tested a saddle shaped superconducting magnet for 8inch silicon wafer growing system. And the protection circuits for HTS current lead and superconducting coil are designed and manufactured. In this paper, their manufacturing process and test results are introduced.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.04a
• /
• pp.250-254
• /
• 2008

Eddy currents are induced when a nonmagnetic conductive material is moving subjected to the magnetic field due to a permanent magnet. These currents circulates in the conductive material and are dissipated, causing a repulsive force between the magnet and the conductor. Using this concept, the eddy current damping can be used as a viscous damping. The present study investigates the characteristics of a magnetic damping analytically and experimentally. The theoretical model of a eddy current damping is developed from electromagnetics and is verified from experiments. The drop test of a magnet in the cooper tube shows that the present model can accurately predict the damping force. Additionally, the dynamic test of a eddy current damping is carried to verify the present model.

• Proceedings of the KIEE Conference
• /
• 2001.04a
• /
• pp.6-8
• /
• 2001

This paper describes the design, fabrication and experimental results for the 1MJ SMES magnet made by using the design code of a SMES device that we developed. The inductance and field measurements indicate that the developed code is applicable to the design of a SMES device. The test results show that the magnet is excellent in comparison with previously fabricated magnets outside.

• Proceedings of the KIEE Conference
• /
• summer
• /
• pp.1082-1084
• /
• 2004

This paper presents simulation and test results of PMSM(Permanent Magnet Sychronous Motor) Controller. PMSM has higher efficiency and torque per volume than other motors because PMSM use permanent magnet of high energy density instead of field winding. PMSM control system also more efficient than Induction Motor's. In this paper, simulation and test to control speed and current of PMSM using DSP was accomplished.