• Journal of the Korean Wood Science and Technology
• /
• 제32권3호
• /
• pp.1-7
• /
• 2004

The application of abrasive-assisted high energy water-jet was investigated as a possible new method of cutting wood. In this study the maximum cutting speeds for species of various wood density were determined and water-jet machining characteristics were investigated for sixteen Korean domestic species. The maximum cutting speed ranged from 200 to 750 mm/min. The results indicate that wood density affects machining characteristics such as maximum cutting speed, surface roughness, and kerf width. Roughness of surface generated increased and kerf width decreased as penetration depth increased.

• Journal of the Korean Wood Science and Technology
• /
• 제24권4호
• /
• pp.87-92
• /
• 1996

When cutting 2.0cm-thick red oak and hard maple with an air-jet-assisted carbon-dioxide laser of 2kW output power, maximum feed speed at the point of full penetration of the beam decreased with increasing the angle between grain and cutting direction. Feed speed averaged 3.75 and 3.38 meters per minute for red oak and hard maple, respectively. Gray-level of laser-cut surfaces were analyzed by image analysis system. The highest gray level of laser-cut surface was obtained when red oak was cut parallel to grain by laser. Surface profiler was used to scan the sawn and laser-cut surfaces. Center line average roughnesses of laser-cut surfaces were higher than those of sawn surfaces. Scanning electron micrographs showed the cell walls which were melted by laser.

• Journal of the Korean Wood Science and Technology
• /
• 제33권5호통권133호
• /
• pp.38-44
• /
• 2005

Peripheral milling is one of the most important wood machining processes in wood industry. Power consumption characteristics of twelve Korean domestic species in peripheral milling were investigated in this study. Image analysis technique was applied to extract proper data from the power consumption profiles. Average power consumption increased as cutting depth increased and specific cutting power decreased as cutting depth increased. However, no significant relationship could be found between density and power consumption and between cutting depth and surface roughness.

• 대한조선학회논문집
• /
• 제44권2호
• /
• pp.174-179
• /
• 2007

The cutting automation of boat's wooden pattern is strongly required to improve the productivity and quality of boats in leisure boat industry. This paper is concerned with the development of wooden pattern machining technology by the machining center. The leisure boat is designed with a 3 dimensional design s/w. The NC cutting data are generated in a CAM s/w and are verified using verification s/w. The cutting forces are monitored to analyse the cutting process. The surface characteristics of machined surface are investigated at various cutting conditions such as spindle speed, feed speed, the cutting direction of wood, and wood material.

• 한국가구학회지
• /
• 제11권1호
• /
• pp.13-23
• /
• 2000

This study was carried out to investigate the wood properties for development the proper uses of lesser-known tree species. The tested species are Kebambang(Pentace sp.), Bawang-bawang(Dysoxylum alliaceum Bl .), Garu buaya( Gonystylus brunescens A. Shaw)grown in Indonesia. fundamental wood properties such as anatomical, physical, mechanical and chemical properties and characteristics related to wood processing were examined. The results are summarized as follows : The woods of these species are diffuse porous, coarse textured, and interlocked grained. The heartwood of Kebambang is distinguished clearly to the sapwood, but the heartwood of other species are not distinguished clearly to the softwood. The woods of Kebambang and Bawang-bawang have the moderate weight density and the low strength properties, but Garu buaya has the high weight density and the high strength properties. The woods of these species has high shrinkage. The sawing characteristics of Kebambang are excellent but the other species are moderate. The machining characteristics by planer and drying characteristics of these species are moderate. These woods has poor characteristics in bending processing and decay durability. The wood of Bawang-bawang has high content of the extractives and lignin.

• 한국가구학회지
• /
• 제19권6호
• /
• pp.411-419
• /
• 2008

Xylia xylocarpa is fast-growing trees that are currently planted on trial basis in Sabah, Malaysia. The wood quality of trees grown in Sabah may differ from those grown in other places due to the environmental factors. Five 9-year-old trees of each species were extracted from their respective plots at Luasong, Tawau. Wood specimens were prepared from three height levels; bottom, middle and top, at the inner and outer radial positions. The within-tree and between-tree variations of physical properties of these species were analyzed. The basic density, oven-dry density and green moisture content(MC) are 0.72g/$cm^3$, 0.78g/$cm^3$ and 49.8% respectively. The shrinkage from green to oven-dry conditions for the radial and tangential directions were 3.35% and 5.76%, respectively. The trends of within-tree variations for most properties were more consistent in radial rather than vertical direction. This suggests diameter growth to be a more important factor contributing to the variations compared to height. Samples from the outer part of the stem were found to have higher density, shrinkage and mechanical strengths. The between-trees variations of some wood properties were found to be significantly different, probably due to genetic and micro-environmental factors. Significant correlation was recorded among the physical properties of the species. The true potential of X. xylocarpa for end-uses would be enhanced by further research such as the study on properties of wood from different sites and other properties like durability, seasoning, processing and machining characteristics. The characteristics of X. xylocarpa are comparable to a number of local popular hardwood species, indicating its suitability for heavy construction uses.

• 한국가구학회지
• /
• 제25권1호
• /
• pp.45-54
• /
• 2014

Wood cutting utilizing CNC art in the field of furniture design industry, art, education are diverse. However, there is lack of data in the case for wood cutting, such as cutting conditions and wood cutting. So this article is to establish furniture design processing using CNC. The researchers investigated the processed products using CNC, the data of the web site and CNC relevant articles, then organized its impact on the furniture industry today. History and definition of CNC have studied for a discussion of the advantages and disadvantages. Then, the researchers analyzed the cases to investigate the wood cutting conditions, was applied to the fabrication of furniture domestic and foreign. CNC organized systematically design information through the computer So, it allowed to reduce the repetitive behavior that has to work hand in the furniture manufacture existing. CNC has made it possible to design a fine complex in furniture design industry. So it became possible to make a new representation and production of various forms. Material about CNC are mostly for milling machine and shelves for metal processing. So, the researchers investigated and precautions general content of wood cutting. The enhanced understanding to investigate an example that is applied outside the country, is used to analyze the expression various techniques CNC. It is difficult to obtain accurate data processing, it has various characteristics in the same timber, Future research is about analyzing type applications and CNC machining range at the time of processing the various wood.

• Journal of the Korean Wood Science and Technology
• /
• 제42권4호
• /
• pp.357-366
• /
• 2014

백합나무 판재를 벽판재로 이용하기 위해 백합나무의 생재와 건조재에 대한 휘발성유기화합물(VOCs)과 알데히드류 방출 특성을 검토하였다. VOCs 및 formaldehyde를 포함한 aldehyde류의 방출량 측정은 다중이용시설 등의 실내공기질 관리법에 공시된 20 ${\ell}$ Chamber법에 따라 실시하였다. 백합나무의 생재 및 건조재에서는 30여 가지 이상의 VOCs가 검출되었다. 백합나무의 Total VOC 구성 비율 가운데 천연VOC (NVOC)의 비율은 11.1%로 다른 침엽수종과 비교하여 낮게 나타났다. 백합나무의 aldehyde류 분석 결과, 심재 및 변재에서 같은 3종(acetaldehyde, ketone, propionaldehyde)이 검출되었으며, formaldehyde의 방출량은 $4.01{\mu}g/m^3$ 이하로 나타났다. m-Tolualdehyde의 경우 백합나무 건조재의 심재에서만 $33.6{\mu}g/m^3$의 방출량을 보였으며, 심재와 변재 모두 ketone의 방출량이 가장 높게 나타났다. 백합나무 특유의 역한 냄새는 acetaldehyde와 propionaldehyde와 기타 VOCs에 의한 것으로 추정된다. 건조한 백합나무에서는 휘발성이 강한 ketone의 방출량이 증가하였다.

• 한국융합학회논문지
• /
• 제8권11호
• /
• pp.115-121
• /
• 2017

의료용 디지털 영상 및 통신 표준과 5축 가공기술의 융합적 연구를 통하여 맞춤형 인공관절의 기초적 지식을 얻고자 하였다. 연구방법으로 의료영상의 위팔뼈에 대해 3차원 모델링을 생성하고 케미컬우드 소재로 형상을 가공하여 해부학적 특징과 모델링 가공 연산시간을 비교하였다. 그 결과 스테레오리소그래피 모델링이 아이제스 모델링에 비해 중삭 2배, 정삭 10배 정도로 시간이 많이 소요되었다. 5축 가공된 위팔뼈는 해부목, 큰돌기, 작은돌기, 결절사이 고랑의 해부학적 구조가 3차원 의료영상과 동일한 특징으로 나타났다. 이와 같이 위팔뼈의 외과목 언더컷 등 다양한 형태의 구조가 5축으로 가공되는 융합적 가공 기술들은 인체의 정밀한 모형을 추구하는 맞춤형 관절 제작 시 향후 적용 가능성이 높음을 알 수 있었다.