• Tribology and Lubricants
• /
• 제16권2호
• /
• pp.121-125
• /
• 2000

Silicon nitride ceramic has been verified as an excellent rolling bearing material because of its high strength and outstanding rolling fatigue life properties. However under some corrosive circumstances it showed drawbacks such as hardness reduction and severe wear caused by corrosion. In this work, the variations of the rolling wear and hardness of three kinds of ceramics were studied for the specimen aged 15 days in alkali water (90 $\pm$ 2$\^{C}$,25 wt% NaOH ). All of the specimens, ① Si$_3$N$_4$, ② 3Y-TZP and ③ 3Y-TZP alloyed with 5 wt% CeO$_2$, were sintered and post-HIPed, and then polished up to 0.02 $\mu$mRa of surface roughness. Rolling wear tests were conducted by MJ type rolling fatigue life tester under the initial theoretical maximum contact stress of 3.16 GPa and the spindle speed of 1,000 rpm. Spindle oil was used as a lubricant. The specimens were not worn before aging. For the specimen aged in alkali water, Si$_3$N$_4$ and 3Y-TZP were worn by rolling wear tests, and hardness was decreased. While aging the specimens, the phase was transformed from tetragonal to monoclinic in 3Y-TZP and the microstructure change occurred in Si$_2$N$_4$. 3Y-TZP specimens alloyed with 5 wt% CeO$_2$ were not worn after aging and no phase transformation occurred while aging.

• 한국세라믹학회지
• /
• 제31권10호
• /
• pp.1147-1158
• /
• 1994

From Zr(O-nC3H7)4-H2O-C2H5OH-HNO3 starting solutions, MgO-doped stabilized zirconia fibers with varying content of MgO (10~18 mol%) from different MgO sources were fabricated by sol-gel method. The MgO sources used are magnesium nitrate hexahydrate, magnesium acetate tetrahydrate, and magnesium ethylate. The phase transformation studies of a drawn MgO-ZrO2 fiber were carried out using X-ray diffraction, IR spectroscopy, and Raman spectroscopy. The microstructure, tensile strength, and microporosity of fibers were investigated using SEM, tensile strength test, and microporosimeter. Although various MgO sources such as magnesium nitrate, acetate, and ethylate were used, the crystallization behavior of MgO-ZrO2 fibers at different temperatures could be summarized as follows: CubiclongrightarrowMetastable TetragonallongrightarrowMonocliniclongrightarrowCoexistence of Monoclinic and CubiclongrightarrowCubic(trace of monoclinic). At 150$0^{\circ}C$, the phase transformation of MgO-ZrO2 fibers shows the following change depending on the amount of MgO[Mg(NO3)2.6H2O]: At 10 mol%, both monoclinic and cubic phase coexist, at 12 mol%, monoclinic phase decreases rapidly, and then at 14 mol%, only cubic phase remains. When the MgO-ZrO2 fibers containing 12 mol% magnesium nitrate were heated at 80$0^{\circ}C$ for 1hr, average tensile strength of fibers is 4.0 GPa at diameters of 20 to 30 ${\mu}{\textrm}{m}$. As the heat-treatment temperatures increase to 100$0^{\circ}C$ for 1 hr, tensile strength of MgO-ZrO2 fibers decreases rapidly to 0.7 GPa.

• 한국세라믹학회지
• /
• 제21권3호
• /
• pp.239-244
• /
• 1984

The effect of tetragonal $ZrO_2$ phase on the mechanical behavior in 7 mole% calcia partially stabilized zirconia has been studied. The $ZrO_2$ powder containg 7 mole% CaO prepared by Hot Petroleum Drying Method calcined at 80$0^{\circ}C$ for 1 hour was nearly 100% tetragonal but as the calcining temperature increased certain amount of monoclinic phase appeared. The sintered specimen at 1$700^{\circ}C$ for 5 hours was aged at 130$0^{\circ}C$ for 0, 24, 48, 72 hours. X-ray diffraction data showed that in the aged specimen monoclinic tetragonal and cubic phase coexisted. The Kc value of aged specimen for 48 hr was about 4.5MN/m3/2 much greater than unaged sample. But aged for 72 hr the KiC value was decreased. The increasing of toughness in PSZ is based on the Stress-Induced Phase Transformation that is metastable tetra-gonal $ZrO_2$ changes t stable monoclinic phase within the stress field of crack and the mechanical fracture energy absorption is occured But in this case due to certain amount of tetragonal phase transformed to monoclinic phase during cooling the microcrack effect by transformation also considered. Trerefore both Stress-Induced Phase Transformation and inclusion induced microcracking effect contrbute to the increase of fracture toughness of 7 mole% CaO-$ZrO_2$ containing monoclinic and tetragnola phase simulataneously.

• 한국세라믹학회지
• /
• 제47권1호
• /
• pp.75-81
• /
• 2010

The feasibility of using the thin film technology in utilizing lanthanum strontium manganite (LSM) for a solid oxide fuel cell (SOFC) cathode in a low-temperature regime is investigated in this study. Thin film LSM cathodes were fabricated using pulsed laser deposition (PLD) on anode-supported SOFCs with yttria-stabilized zirconia (YSZ) electrolytes. Although cells with a 1 ${\mu}m$-thick LSM cathode showed poor low-temperature cell performance compared to that of a cell with a bulk-processed cathode due to the lack of a triple-phase boundary length, the cell with 200 nm-thick gadolinia-doped ceria (GDC) inserted between the LSM and YSZ showed enhanced performance and more stable operation characteristics in a comparison of a cell without a GDC layer. We postulate that the GDC layer likely improved the cathode adhesion, therefore contributing to the improvement of the cell performance instead of serving as an interfacial reaction buffer.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 1999년도 제17회 학술발표회 논문개요집
• /
• pp.87-87
• /
• 1999

본 연구에서는 Pulsed Laser Deposition(이하 PDL)방법을 이용하여 Si기판에 (Ba,Sr)TiO3(이하 BST)박막을 MFS-FET(Metal-Ferroelectric-Semiconductor Field-effect Transistor)구조로 제조하였으며 BST박막의 강유전성이 BST 박막에 유도되는 응력에 어떤 영향을 받는지 살펴보았다. 본 연구에서는 완충막을 사용함으로써 BST박막과 완충막간의 격자부정합을 이용하여 BST박막에 강유전성을 유도하려고 하였다. 또한 MFS-FET구조의 BST박막에 유도되는 응력조절을 위하여 BST박막과 완충막의 두께를 변화하였으며 XRD를 통한 구조 분석 및 C-V test를 통한 전기적 특성을 관찰을 하였다. PLD법을 통해서 epitaxial 성장된 BST 박막에서는 Si에 epitaxial 성장된 완충막과의 격자부정합에 의한 BST박막내의 자발분극의 발생이 예상된다. 따라서, 본 연구는 강유전체의 자발분극에 의하여 발생되는 C-V 이력현상이 BST박막과 완충막과의 격자부정합에 의한 응력에 의해 발생될 것으로 예상하여, BST 박막에 유도되는 응력과 C-V 이력현상의 관계를 통하여 상온에서 상유전성을 갖는 BST가 응력에 의하여 어느 정도의 강유전성을 나타내는지를 밝히기 위해 진행되었다. 본 연구에서 사용된 완충막은 YSZ(Yttria Stabilized Zirconia)박막으로 0.4mTorrO2 분위기 하에서 600~80$0^{\circ}C$의 온도에서 증착하여 상형성을 살펴보았고 $700^{\circ}C$에서 epitaxial 성장을 확인하였으며 두께는 30~$\AA$으로 변화하였다. 또한 BST박막은 완충막과의 전압분배를 고려해 300~2000$\AA$으로 두께를 변화를 시키며 증착하였다. MFS 구조에서 Al 전극을 사용하여 완충막과 BST박막간의 두께 변화에 따른 Capacitance - Voltage(C-V) 측정을 하였으며 이를 통하여 강유전상의 특성인 C-V 이력현상을 관찰하였다. 그 결과 YSZ 박막에서는 C-V 이력현상이 나타나지 않았으며 BST 박막에서는 약 1.2V의 C-V이력현상이 보였다.

• Progress in Superconductivity
• /
• 제8권2호
• /
• pp.175-180
• /
• 2007

High temperature superconductor $YBa_2Cu_3O_{7-x}$ (YBCO) films have been grown by in-situ electron beam evaporation on artificial metal tapes such as ion-beam assisted deposition (IBAD) and rolling assisted biaxially textured substrates (RABiTS). Deposition rate of the YBCO films is $10{\sim}100{\AA}/sec$. X-ray diffraction shows that the films are grown epitaxially but have inter-diffusion phases, like as $BaZrO_3\;or\;BaCeO_3$, at their interfaces between YBCO and yttrium-stabilized zirconia (YSZ) or $CeO_2$, respectively. Secondary ion mass spectroscopy depth profile of the films confirms diffused region between YBCO and the buffer layers, indicating that the growth temperature ($850{\sim}900^{\circ}C$) is high enough to cause diffusion of Zr and Ba. The films on both the substrates show four-fold symmetry of in-plane alignment but their width in the -scan is around $12{\sim}15^{\circ}$. Transmission electron microscopy shows an interesting interface layer of epitaxial CuO between YBCO and YSZ, of which growth origin may be related to liquid flukes of Ba-Cu-O. Resistivity vs temperature curves of the films on both substrates were measured. Resistivity at room temperature is between 300 and 500 cm, the extrapolated value of resistivity at 0 K is nearly zero, and superconducting transition temperature is $85{\sim}90K$. However, critical current density of the films is very low, ${\sim}10^3A/cm^2$. Cracking of the grains and high-growth-temperature induced reaction between YBCO and buffer layers are possible reasons for this low critical current density.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 1999년도 제30회 추계학술대회
• /
• pp.154-159
• /
• 1999

Silicon nitride ceramic has been verified as an excellent rolling bearing material because of its high strength and outstanding rolling fatigue life properties. However under some corrosive circumstances it showed drawbacks such as hardness reduction and severe wear caused by corrosion. In this work, the variations of the rolling wear and hardness of three kinds of ceramics were studied for the specimen aged 15 days in alkali water (90$\pm$2$^{\circ}C$, 25 wt% NaOH). All of the specimens, \circled1Si$_3$N$_4$, \circled23Y-TZP and \circled33Y-TZP alloyed with 5 wt% CeO$_2$, were sintered and post-Hipped, and then polished up to 0.02 ${\mu}{\textrm}{m}$Ra of surface roughness. Rolling wear tests were conducted by MJ type rolling fatigue life tester under the initial theoretical maximum contact stress or 3.76 Gra and the spindle speed of 1,000 rpm. Spindle oil was used as a lubricant. The specimens were not worn before aging. For the specimen aged in alkali water, Si$_3$N$_4$and 3Y-TZP were worn by rolling wear tests, and hardness was decreased. While aging the specimens, the phase was transformed from tetragonal to monoclinic in 3Y-TZP and the microstructure change occurred in Si$_3$N$_4$. 3Y-TZP alloyed with 5 wt% CeO$_2$specimens were not worn after aging and no phase transformation occurred while aging.

• 한국분말재료학회지
• /
• 제17권2호
• /
• pp.148-153
• /
• 2010

Thermal barrier systems have been widely investigated over the past decades, in order to enhance reliability and efficiency of gas turbines at higher temperatures. Yttria-stabilized zirconia (YSZ) is one of the most leading materials as the thermal barriers due to its low thermal conductivity, thermodynamic stability, and thermal compatibility with metal substrates. In this work, rare-earth oxides with pyrochlore phases for thermal barrier systems were investigated. Pyrochlore phases were successfully formed via solid-state reactions started from rare-earth oxide powders. For the heat-treated samples, thermo-physical properties were examined. These rare-oxide oxides showed thermal expansion of $9{\sim}12{\times}10^{-6}/K$ and thermal conductivity of 1.2~2.4 W/mK, which is comparable with the thermal properties of YSZ.

• The Journal of Advanced Prosthodontics
• /
• 제12권4호
• /
• pp.233-238
• /
• 2020

PURPOSE. This study aims to compare the marginal fitness of two types of implant-supported fixed dental prosthesis, i.e., cementless fixation (CL.F) system and cement-retained type. MATERIALS AND METHODS. In each group, ten specimens were assessed. Each specimen comprised implant lab analog, titanium abutment fabricated with a 2-degree tapered axial wall, and zirconia crown. The crown of the CL.F system was retained by frictional force between abutment and relined composite resin. In the cement-retained type, zinc oxide eugenol cement was used to set crown and abutment. All specimens were sterilized with ethylene oxide, immersed in Prevotella intermedia culture in a 50 mL tube, and incubated with rotation. After 48 h, the specimens were washed thoroughly before separating the crown and abutment. The bacteria that penetrated into the crown-abutment interface were collected by washing with 500 µL of sterile saline. The bacterial cell number was quantified using the agar plate count technique. The BacTiter-Glo Microbial Cell Viability Assay Kit was used to measure bacterial adenosine triphosphate (ATP)-bioluminescence, which reflects the bacterial viability. The t-test was performed, and the significance level was set at 5%. RESULTS. The number of penetrating bacterial cells assessed by colony-forming units was approximately 33% lower in the CL.F system than in the cement-retained type (P<.05). ATP-bioluminescence was approximately 41% lower in the CL.F system than in the cement-retained type (P<.05). CONCLUSION. The CL.F system is more resistant to bacterial penetration into the abutment-crown interface than the cement-retained type, thereby indicating a precise marginal fit.

• 한국세라믹학회지
• /
• 제55권4호
• /
• pp.344-351
• /
• 2018

The effects of bond coat species on the growth behavior of thermally grown oxide (TGO) layer in thermal barrier coatings (TBCs) was investigated through furnace cyclic test (FCT). Two types of feedstock powder with different particle sizes and distributions, AMDRY 962 and AMDRY 386-4, were used to prepare the bond coat, and were formed using air plasma spray (APS) process. The top coat was prepared by APS process using zirconia based powder containing 8 wt% yttria. The thicknesses of the top and bond coats were designed and controlled at 800 and $200{\mu}m$, respectively. Phase analysis was conducted for TBC specimens with and without heat treatment. FCTs were performed for TBC specimens at $1121^{\circ}C$ with a dwell time of 25 h, followed by natural air cooling for 1 h at room temperature. TBC specimens with and without heat treatment showed sound conditions for the AMDRY 962 bond coat and AMDRY 386-4 bond coat in FCTs, respectively. The growth behavior of TGO layer followed a parabolic mode as the time increased in FCTs, independent of bond coat species. The influences of bond coat species and heat treatment on the microstructural evolution, interfacial stability, and TGO growth behavior in TBCs are discussed.