• 한국재료학회:학술대회논문집
• /
• 한국재료학회 2012년도 춘계학술발표대회
• /
• pp.57.2-57.2
• /
• 2012

산소 이온 전도성 세라믹을 이용한 고체 산화물 연료전지의 전극은 원활한 전기화학반응을 위해, 이온 전도도, 전자 전도도 및 전기화학적 활성을 동시에 가지고 있어야 한다. 이를 위해 복합체 전극을 사용하며, 특히 음극의 경우 니켈(Nickel)과 Yttria-stabilized zirconia (YSZ)로 이루어진 복합체 전극을 혼합 및 소결을 통해 제조하여 사용하였다. 하지만, 니켈의 경우 탄화 수소 연료에서의 탄소 침적 문제와 열악한 산화환원 안정성(redox stability)등의 문제점을 가지고 있다. 따라서 니켈대신 전도성 세라믹을 사용한 세라믹 복합체 음극 개발이 활발히 이루어지고 있으며, 그 중 침투법(infiltration method)을 이용한 복합체 전극 제조 방법을 소개한다. 실제로 니켈 금속과 유사한 높은 전기 전도도를 갖는 Sr-doped Lanthanum Vanadate (LSV)을 이용해, YSZ-LSV 복합체 전극을 침투법을 이용해 제조하고, 소량의 촉매을 첨가하여, 이온전도도, 전자 전도도 및 촉매 활성을 갖는 복합체 음극을 제조하였다. 이 복합체 음극의 탄화수소에서의 연료전지 성능 및 redox stability을 측정하였다.

• 한국세라믹학회지
• /
• 제30권12호
• /
• pp.1059-1065
• /
• 1993

The sliding wear behavior of the plasma sprayed zirconia containing 8wt% yttria was investigated over a range of room temperature to 800℃. Both of the friction coefficient and the wear loss increased reaching its maximum at about to 499℃. and then decreased again with increasing temperature up to 800℃. The worn surface at elevated temperature were observed and analyzed by scanning electron microscopy and X-ray diffractometer to study the mechanisms of high temperature wear behavior. Surface morphology of the worn samples changes with temperature. Monoclinic (m)/tetragonal (t) x-ray peak intensity ratio of wear debris and worn surface decreased with increasing temperature. Non-transformable tetragonal (t') to metastable tetragonal (t) phase transformation of worn surface increased with increasing temperature. The results indicate that dehumidification and above phase changes are contributing to the high temperature wear behavior of the plasma sprayed ZrO2-Y2O3 coatings.

• 한국세라믹학회지
• /
• 제23권4호
• /
• pp.78-84
• /
• 1986

Zirconium acetate solution which was obtained from $ZrOCl_2$.$8H_2O$ was condensed polymerized and drawn to fibers by pulling method. Drawn gel fibers fired at 130$0^{\circ}C$ were short porous and mechanically weak. But addition of CaO about 13m/o caused the fibers to have the cubic structure and relatively dense microstructure. In order to clarify the condition for the synthesis of zirconia fibers viscosity measurement DTA-TG analysis X-ray diffraction infrared spectroscopy, SEM and specific surface area were studied.

• 한국세라믹학회지
• /
• 제29권2호
• /
• pp.119-126
• /
• 1992

3 mol% Y2O3-doped ZrO2 powders were prepared by hydrolysis with 0.1, 0.2, 0.3, 0.4, 0.5, 0.6 mol/ιH2O/ethanol into 0.1 mol/ι zirconium and yttrium alkoside/ethanol. Spherical monodispersed yttria-partially stabilized zirconia particles with an average diameter of about 0.5 ${\mu}{\textrm}{m}$ were prepared by hydrolysis with 0.2 mol/ιH2O/ethanol. The as-prepared powder was amorphous and with heating it transformed into cubic up to 80$0^{\circ}C$ and into tetragonal over 100$0^{\circ}C$. 3 mol% Y2O3-doped ZrO2 powders calcined over and up to 80$0^{\circ}C$ were a mixture of tetragonal and monoclinic and only tetragonal as determined by X-ray diffraction, respectively.

• Steel and Composite Structures
• /
• 제44권1호
• /
• pp.17-31
• /
• 2022

This investigation studies the characteristics of wave dispersion in sigmoid functionally graded (SFG) curved beams lying on an elastic substrate for the first time. Homogenization process was performed with the help of sigmoid function and two power laws. Moreover, various materials such as Zirconia, Alumina, Monel and Nickel steel were explored as curved beams materials. In addition, curved beams were rested on an elastic substrate which was modelled based on Winkler-Pasternak foundation. The SFG curved beams' governing equations were derived according to Euler-Bernoulli curved beam theory which is known as classic beam theory and Hamilton's principle. The resulted governing equations were solved via an analytical method. In order to validate the utilized method, the obtained outcomes were compared with other researches. Finally, the influences of various parameters, including wave number, opening angle, gradient index, Winkler coefficient and Pasternak coefficient were evaluated and indicated in the form of diagrams.

• 분석과학
• /
• 제6권2호
• /
• pp.225-229
• /
• 1993

알루미나 강화 지르코니아(10-30ATZ) 제조에 있어 지르코니아(TZ-2Y or TZ-0Y)와 알루미나(AKP-30) 분말 slurry에 2wt% 알루미나에 해당하는 알루미나졸을 첨가한 후 겔화시킴으로써 분말이 고르게 분산되어 있고, 동시에 알루미나겔이 분말의 표면을 코팅함으로써 응집이 일어나는 것을 막았다. 이렇게 제조된 ATZ는 $1450{\sim}1550^{\circ}C$ 이상에서 2시간 소결로 알루미나 grain이 $0.5{\mu}m$ 이하로 잘 분포되어 있는 좋은 미세구조와 이론 밀도의 99% 이상의 소결밀도를 보여 주었다. 또한 20ATZ 부근에서의 $K_{IC}$값은 ${\sim}8MPa{\cdot}m^{1/2}$으로 볼-밀링으로 얻는 $6MPa{\cdot}m^{1/2}$보다 높은 값을 보여주고 있다.

• 한국재료학회지
• /
• 제23권9호
• /
• pp.531-536
• /
• 2013

This paper investigates the effect of prolonged high temperature exposure on concentric laminated $Al_2O_3-ZrO_2$ composites. An ultrafine scale microstructure with a cellular 7 layer concentric lamination with unidirectional alignment was fabricated by a multi-pass extrusion method. Each laminate in the microstructure was $2-3{\mu}m$ thick. An alternate lamina was composed of 75%$Al_2O_3$-(25%m-$ZrO_2$) and t-$ZrO_2$ ceramics. The composite was sintered at $1500^{\circ}C$ and subjected to $1450^{\circ}C$ temperature for 24 hours to 72 hours. We investigated the effect of long time high temperature exposure on the generation of residual stress and grain growth and their effect on the overall stability of the composites. The residual stress development and its subsequent effect on the microstructure with the edge cracking behavior mechanism were investigated. The residual stress in the concentric laminated microstructure causes extensive micro cracks in the t-$ZrO_2$ layer, despite the very thin laminate thickness. The material properties like Vickers hardness and fracture toughness were measured and evaluated along with the microstructure of the composites with prolonged high temperature exposure.

• 한국세라믹학회지
• /
• 제33권4호
• /
• pp.411-417
• /
• 1996

Ultrafine NiO/YSZ (Yttria Stabilized Zirconia) powders were made by using a glycine nitrate process which is used as anode material for solid oxide fuel cells. The specific surface areas of synthesized NiO/YSZ powders were examined with controlling pH of a precursor solution and the content of glycine. The binding of glycine with metal nitrates occurring in the precursor solution was analyzed by using FTIR. The characteristics of synthesized powders were examined with X-ray diffraction(XRD) Brunauer Emmett Teller with N2 absorption. scanning electron microscopy (SEM). and transmission electron microscopy (TEM). Ultrafine NiO/YSZ powders of 15-18 m2/g were obtained through GNP when the content of glycine was controlled to 1 or 2 times the stoichiometric ratio in the precursor solutions. Strongly acid precursor solution increased the specific surface area of the synthesized powders. This is suggested to be the increased binding of metal nitrates and glycine under a strong acid solution of pH=0.5 that lets glycine consist of mainly the amine group of {{{{ { NH}`_{3 } ^{+ } }}. After sintering and reducing treatment of NiO/YSZ powders synthesized by GNP the Ni/YSZ pellet showed ideal microstructure where very fine Ni particles of 3-5 ${\mu}{\textrm}{m}$ were distributed uniformly and fine pore around Ni metal particles was formed. leading to anincrease of the triple phase boundary among gas Ni and YSZ.

• 한국분말재료학회지
• /
• 제8권3호
• /
• pp.201-206
• /
• 2001

$>LaMnO_3$$(La, Sr)MO_3$, and $(La, Sr)MO_3/YSZ$ gel films were deposited by spin-coating technique on scandium-doped zirconia (YSZ) substrate using the precursor solution prepared from $La(O-i-C_3H_7)_3$, $Co(CH_3COO)_2$or $Mn(O-i-C_3H_7)_2$,2-methoxyethanol, and polyethylene glycol. By heat-treating the gel films, the electrochemical cells, $(La, Sr)MnO_3{\mid}ScSZ{\mid}Pt$ were fabricated. The effect of polyethylene glycol on the microstructure evolution of $$LaCoO_3and $LaMnO_3$thin films was investigated, and NOx decomposition characteristics of the electrochemical cells were investigated at $500^{\circ}C$ to $600^{\circ}C$. By applying a direct current to the $(La, Sr)MnO_3{\mid}ScSZ{\mid}Pt$ electrochemical cell, good NOx conversion rate could be obtained relatively at low current value even if excess oxygen is included in the reaction gas mixture.

• 한국표면공학회지
• /
• 제30권4호
• /
• pp.285-297
• /
• 1997

Finned segment, with which are lined inner wall of the turbine combustors, are subject to severe degradation when they are exposed to a hostile environmment at elevated temperature. To protect the finned segment from this environment and to maintain good mechanical properties of components at high temperature, they are preferred to be coated. The most governing factor for the durability of coatings used in the high temperature is the microstructure of coatings; these are splat from, distibution of microcacks, size and distribution of pores, thickness of coating layer, adhesion between coating layer, and oxidation of band coating. In this study, based on the evaluation of the imported finned segment, new finned segment segment was manufactured with optimum plasma spraying parameters, and their properties were examined. Using $ZrO_2(8wt$Y_2O_3)$,/TEX> powder for ceramic coating and 67Ni-22Cr-10Al-0.5Y mixing powder for bond coating, thickness of ceramic and bond coating layer were varied in order to find optimum condition, the results showed that B2T4(bond coating : 100~250$\mu\textrm{m}$, ceramic coating : 250~300$\mu\textrm{m}$) was the best among the specimens tested. Compared to the imported finned segment, B2T4 has better bond strength, hardness, and isothermal and cyclic oxidation resistance.