• Advances in concrete construction
• /
• 제6권5호
• /
• pp.465-483
• /
• 2018

The most crucial factor determining the pumping performance of concrete is the characteristics of the lubricating layer formed between the pipe wall and the inner concrete. Thus, it is important to accurately identify the rheological properties of the lubricating layer to predict the pumping of concrete. In this study, a new method is proposed for measuring the rheological properties of the lubricating layer with improved convenience. To verify the new method, a pumping test was conducted with 337 m-long horizontal piping. The rheological properties of the lubricating layer were assessed by a previously verified method and the new method proposed in this study for a total of four concrete mixtures with design strength ranging from 27 MPa to 60 MPa. The correlation between the existing method and the new method in relation to the viscosity of the lubricating layer was determined, and it was possible to predict the pumping performance with an accuracy of about 88.5% using the viscosity of the lubricating layer obtained from this correlation.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.107-110
• /
• 2005

Tribological behaviors of carbon epoxy composites whose surfaces have many small grooves were compared with respect to coating method under dry sliding and water lubricating conditions. The surface coating materials were epoxy (Ep) and polyethylene (PE) mixed with self-lubricating $MoS_2$ and PTFE powders. The wear morphology of the composites observed with a scanning electron microscopic (SEM) revealed that the surface coating layer mixed with the self-lubricating powder on the grooved surface significantly improved the wear resistance under water lubricating condition because the surface coating layer blocked water to penetrate the composite surface and the self-lubricating powder reduced the wear on the coating by suppressing the generation of blisters.

• Advances in concrete construction
• /
• 제13권5호
• /
• pp.395-410
• /
• 2022

This study collected the results of material tests and full-scale pumping tests using 127 types of concrete mixtures with compressive strength ranging from 24 to 200 MPa. The results of 242 material tests showed high correlations between the viscosity of the lubricating layer and concrete, between the slump and the yield stress of concrete, between the water-binder ratio and the viscosity of lubricating layer, and between the time required to reach 500 mm of slump flow and concrete viscosity. Based on these correlations, pumpability was predicted using 101 pumping test conditions, and their accuracy was compared to the actual test results. When the rheological properties of concrete and the lubricating layer were directly measured, the prediction result showed the highest accuracy. A high accuracy can be achieved when the measured viscosity of the lubricating layer, a key determinant of concrete pumpability, is reflected in the prediction of pumpability. When measuring rheological properties is difficult, the slump test can be used to quantitatively predict the pumpability despite the lower accuracy than those of other prediction methods.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2004년도 학술대회지
• /
• pp.130-136
• /
• 2004

Presence of water in the lubricating oils could be one of the first indicators of potentially expensive and possibly catastrophic failure of the machine as it may cause displace the oil films to prevent the lubrication function of the oil or chemically react with many oil additives resulting in the oil degradation. In order to detect water content quantitatively in lubricating oils many methods and sensors has been developed. Among these, capacitive sensors including sensitive layer, whose dielectric factor changes according to the water content absorbed in the layer, are proposed mainly in the market. But these sensors are not sensitive to a high water content. Besides, the absorbing layer soils in time. In this work, an evaporation of water moisture from oil into air volume above lubricant surface and condensation of water vapor at a cooling surface was used to measure water content quantitatively in an lubricating oil. Laboratory test results of a prototype sensor were presented. Test results showed that the proposed method could be avaliable to measure a low levels of oil moisture.

• 열처리공학회지
• /
• 제12권2호
• /
• pp.136-144
• /
• 1999

The study on the wear characteristics of compound layers formed during gaseous nitrocarburising in the medium carbon boron steels and the plain carbon steel has been carried out by using a pin-on-disc type wear test machine under the oil lubricating condition at room temperature and by varying applied loads, sliding speeds and wear distances. Values of friction coefficient measured at the sliding speed of 0.4m/sec under the oil lubricating condition have been shown to decrease considerably with increasing applied load and become gradually a constant value as load is increased to a higher value, showing that the transition load for friction coefficient appears at an applied load of 247.2N. The length and volume wear rates of compound layer have been revealed to relatively constantly increase, also showing that the wear life per unit thickness of compound layer turns out to be superior as porous layer has a denser and thinner appearance. As the sliding speed increases during wear test performed by varying sliding speed at a load of 63.2N under the oil lubricating condition for medium carbon boron steel nitrocarburised in gas atmosphere, the wear rate has been found to increase, the friction coefficient to decrease and the wear life per unit thickness of compound layer to decrease considerably.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 1999년도 Proceedings of Pre-symposium of the 10th ISWPC
• /
• pp.204-208
• /
• 1999

Friction was measured on filter paper sheets impregnated with model compounds representing wood extractives using an apparatus based on the horizontal plane principle. The best lubrication of paper surfaces was achieved when they were completely separated by a densely packed film of saturated long-chain amphophilic molecules, such as fatty acids. The fatty acids adsorbed with their polar ends on the paper surface, causing their hydrocarbon chaine to be orientated perpendicularly to the paper surface. The saturated C18-acid, stearic acid, was an efficient lubricator for paper surfaces. The introduction of a double bond in stearic acid eliminated its lubricating ability. The spatial length of the lubricating fatty acid thereby decreases from 24${\AA}$ to 11${\AA}$. However the transisomer of oleic acid, elidic acid, had the ability to lower friction due to an increased spatial length of the fatty acid. Both the spatial length of the hydrocarbon chain and the number of lubricating chains may be of importance for the paper-to-paper friction caused by wood extractives. A hydrophilic head-graup in the wood extractive and an ordered molecular layer of lubricating molecules seems also to be prerequisites for efficient lubrication. A chemical weak boundary layer between the paper sheets was suggested to cause the low friction when long chain saturated fatty acids were deposited on paper.

• 비파괴검사학회지
• /
• 제23권6호
• /
• pp.577-582
• /
• 2003

This paper describes a new technique for thickness measurement of a very thin layer less than one-quarter of the wavelength of ultrasonic wave used in the ultrasonic pulse-echo measurements. The technique determines the thickness of a thin layer in a tapered medium from constructive interference of multiple reflection waves. The interference characteristics are derived and investigated in theoretical and experimental approaches. Modified total reflection wave g(t) defined as difference between total and first reflection waves increases in amplitude as the interfacial layer thickness decreases down to zero. A layer thickness less than one-tenth of the ultrasonic wavelength is measured using the maximum amplitude of g(t) with a good accuracy and sensitivity. The method also requires no inversion process to extract the thickness information from the waveforms of reflected waves, so that it makes possible to have the on-line thickness measurement of a thin layer such as a lubricating oil film in thrust bearings and journal bearings during manufacturing process.

• Tribology and Lubricants
• /
• 제15권3호
• /
• pp.265-271
• /
• 1999

Wherever there are rotating equipment and contact between surface, there is wear and the generation of wear particles. The particles contained in the lubricating oil carry detailed and important information about the condition monitoring of the machine. This information may be deduced from particle shape, composition, size distribution, and concentration. Therefore, This paper was undertaken to Ferrography system of wear debris generated from lubricated moving machine surface. The lubricating wear test was performed under different experimental conditions using the Falex wear test of Pin and V-Block type by Ti(C, N) coated. It was shown from the test results that wear particle concentration (WPC) and wear severity Index( $I_{S}$), size distribution in normal and abnormal wear have come out all the higher value by increases sliding friction time. Wear shape is observed on the Ferrogram it was discovered a thin leaf wear debris as well as ball and plate type wear particles. This kind of large wear shape have an important effect not only metals damage, but also seizure phenomenon.

• Tribology and Lubricants
• /
• 제16권5호
• /
• pp.341-350
• /
• 2000

The study reported in this paper deals with the development for parametric investigation of the influence of the rheological properties of the lubricant in the thermohydrodynamic (THD) film conditions which occur in slider and journal bearings. A parametric investigation based on a Bingham model with a shear yield stress which best fit the experimental pressure is performed for predicting the thickness of the shear Bone in lubricating films with fixed geometry between the stationary and moving surfaces. The results suggest that the shear yield stress for the lubricating film is proportional to the pressure developed in the film within the range of the investigated cases and the shear zone thickness which is of the same order of magnitude as that obtained by the empirical formula is significantly smaller than the fluid film thickness in the lubrication zone.

• International Journal of Concrete Structures and Materials
• /
• 제10권sup3호
• /
• pp.75-85
• /
• 2016

Large scale constructions needs to estimate a possibility for pumping concrete. In this paper, the state of the art on prediction of concrete pumping including analytical and experimental works is presented. The existing methods to measure the rheological properties of slip layer (or called lubricating layer) are first introduced. Second, based on the rheological properties of slip layer and parent concrete, models to predict concrete pumping (flow rate, pumping pressure, and pumpable distance) are explained. Third, influencing factors on concrete pumping are discussed with the test results of various concrete mixes. Finally, future need for research on concrete pumping is suggested.