• Journal of Magnetics
• /
• v.7 no.2
• /
• pp.29-39
• /
• 2002

The initial NiCuZn synthetic ferrite were acquired from thermally decomposing the metal nitrates $Fe(NO_3)_39H_2O, Zn(NO_3)_26H_2O, Ni(NO_3)_26H_2O, and Cu(NO_3)_23H_2O$ at $150^circ{C}$ for 24 hours, and then we calcined the synthetic powder at $500^circ{C}$, pulverized each of those for 3, 6, 9, 12, and 15 hours in a steel ball mill, sintered each at $700^circ{C}$ to $1,000^circ{C}$ for 1 hour, and thus studied their microstructures and electromagnetic properties. We could make the initial specimens chemically bonded in liquidity at a low-temperature $150^circ{C}$, by using the low melting points less than $200^circ{C}$ of the metal nitrates instead of the mechanical ball-mill pulverization, then narrow a distance between the particles into a molecular one, and thus lower the reaction point of sintering by at least $200^circ{C}$ to $300^circ{C}$. Their initial permeability was 50 to 400 and their maximum magnetic induction density and coercive force, 2,400 G and 0.3 Oe to 0.5 Oe respectively, which was similar to those of NiZnCu ferrite synthesized in the conventional process. In the graph of initial permeability by frequencies, a $180^circ{C}$ rotation of the magnetic domains which appears in a broad band of micro-wave before and after the resonance frequency, could be perceived.

• Food Science and Preservation
• /
• v.4 no.2
• /
• pp.115-122
• /
• 1997

This experiment was hocused on the improvement of postharvest management of fresh shiitake to increase the marketing duration. the respiration rate of fresh shiitake at 2$0^{\circ}C$ was ranged from 395mg to 551mg CO2/kg/hr depending on the cultural condition. The rapid precooling is considered as one of the most important postharsvest management to remain shiitake quality. The optimum temperature for precooling and storage was -3$^{\circ}C$ because the occurrence of physical damage on frozen tissue at below -5$^{\circ}C$. Frozen storage at -3$^{\circ}C$ had benefits to minimize weight loss, browning induction at gill tissue and consumption of stored materials where as storage at $0^{\circ}C$ appeared not to be adequite for the extension of marking duration. Frozen shiitake was succesefully thawed when exposed to RH 40-50% at below 1$0^{\circ}C$.

• Applied Chemistry for Engineering
• /
• v.28 no.5
• /
• pp.513-520
• /
• 2017

The application possibility of an alternative new method with low energy consumption was studied for the eco-friendly fabrication of foamed glasses from waste glasses. As a result, fabricating temperature can be reduced under $300^{\circ}C$ without using various expensive inorganic oxidants. The foamed glass can be fabricated at a proper mixing ratio of the waste glass powder, water glass, little surfactant and bubble stabilizer by induction heating method. In the experimental range, the assured optimal condition is 4 min heating on the induction machine with a steel-container ($100mm{\times}100mm{\times}20mm$) and followed by evaporating and drying process for 11 min with 110 g of glass powder, 80 g of water glass, 3 g of surfactant and 0.2 g of bubble stabilizer. When the foamed glass was fabricated at the optimal condition, the density of the glass was $0.85g/cm^3$ and the heat conduction was $0.052W/h{\cdot}K$. In addition, the compressive strength of the glass was above $50kg/cm^2$.

• KSBB Journal
• /
• v.10 no.5
• /
• pp.533-539
• /
• 1995

An autolytic system based on a thermally inducible phage lambda, λHL1, has been applied for the recovery of poly(3-hydroxybutyrate) [PHB] from a recombinant Escherichia coli XL1-Blue, harbouring a plasmid (pSYL105) containing the Alcaligenes eutrophus PHB biosynthesis genes. The lytic capability ofλHL1 was evaluated in flask culture for both lysogens, XL1-Blue (λHL1) and XL1-Blue (λHL1, pSYL105). When the optical density of culture at 600nm(OD600) reached 0.2, cell lysis was induced by increasing the temperature from $30^{\circ}C$ to $42^{\circ}C$. Most cells of XL1-Blue ($\lambda$HL1) were lysed by the autolytic system in an hour after the thermal induction, while the lytic efficiency was slightly lower for XLl-Blue (λHL1, pSYL105). The existence of pSYL105 in cells seemed to inhibit, to some extent, the lytic capability of λHL1 even at low PHB content. The lylic efficiency remarkably decreased as the induction was delayed to allow PHB accumulation. When a chemical induction using 2% (v/v) chloroform was introduced after an hours of thermal induction, we could obtain a good lytic efficiency.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.06a
• /
• pp.94-97
• /
• 2005

For the fabrication of poly-crystalline silicon ingot, CCCC (Cold Crucible Continuous Casting) method under a high frequency alternating magnetic field, was utilized in order to prevent crucible consumption and ingot contamination and to increase production rate. In order to effectively and continuously melt and cast silicon, which has a high radiation heat loss due to the high melting temperature and a low induction heating efficiency due to a low electric conductivity, Joule and pinch effects were optimized. Throughout the present investigation, poly-crystalline Si ingot was successfully produced at the casting speed of above 1.5 mm/min under a non-contact condition.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.4
• /
• pp.179-184
• /
• 2021

Two types of secondary hardening martensitic steels, 10Co-14Ni and 6Co-5Ni, were produced by vacuum induction melting to investigate the effect of ausforming process on mechanical properties. According to the results of present study, the alloy samples ausformed at low temperature indicated a rather low hardness level in overall aging time despite the refinement of martensite lath width. As the result can closely be related with the presence of primary carbides precipitated within the initial austenite matrix, we confirmed that, in ultrahigh strength secondary hardening martensitic alloy steels, the ausforming process can rather limit the degree of secondary hardening during the subsequent aging treatment.

• Journal of Photoscience
• /
• v.8 no.3_4
• /
• pp.105-112
• /
• 2001

Susceptibility to low temperature photoinhibition in photosynthetic apparatus was compared among three cucumber cultivars, Gahachungjang (GH), Banbaekjijeo (BB) and Gaeryangsymji (GR). By chilling in the light for 6 h, a sustained decrease in the potential quantum yield (Fv/Fm) and the oxidizable P700 contents was observed, and the decrease was less in GH than in BB and GR. Although the difference was small, some $\Phi_{PSII}$ remained in GH after light-chilling for 6 h indicating that a few electrons can flow around photosystem II(PSII). As a consequence, the primary electron acceptor of PSII, $Q_{A}$, was reduced slowly and was not fully reduced after light-chilling for 6 h in GH. Although the amplitude was small, the development of NPQ was also faster in GH, indicating a higher capacity for non-photochemical energy dissipation. The relative fraction of a fast relaxing component of NPQ (qf) was higher in GH. After light-chilling for 5 h, the values of qf in BB and GR became much smaller than that in GH, indicating BB and GR suffered more significant uncoupling of ATPase and/or irreversible damages in PSII. When fluorescence induction transients were recorded after chilling, significant differences in quenching coefficients (qQ and qN) were observed among the three cultivars.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.163-166
• /
• 1997

Aluminium foam material is a highly porous material having complicated cellular structure defined by randomly distributed air pores in metallic matrix. this structure gives the aluminium a set of properties which cannot be achieved by any of conventional treatments. The properties of aluminium foam material significantly depend on its porosity, so that a desired profile of properties can be tailored by changing the foam density. Melting method is the one of foaming processes, which the production has long been considered difficult to realize becaues of such problems as the low foamability of molten metal, the varying size of. cellular structures, solidification shrinkage and so on. These problems, however, have gradually been solved by researchers and some manufacturers are now producing foamed aluminum by their own methods. Most of all, the parameters of solving problem in electric furnace were stirring temperature, stirring velocity, foaming temper:iture, and so on. But it has not considered about those in induction heating, foaming velocity and foaming temperature in semi-solid state yet. Therefore, this paper presents the effects on these parameter to control cell size, quantity and distribution.

• Journal of Drive and Control
• /
• v.18 no.4
• /
• pp.84-90
• /
• 2021

Viscosity of hydraulic oils decreases due to loss reduction and efficiency increase of fluid power systems. However, low viscosity is not always appropriate due to the induction of large leakage and small lubricity. Therefore, a detailed study on the optimum viscosity of hydraulic oils is necessary. In this study, based on the thermohydrodynamic lubrication theory, numerical simulation was conducted using the slipper model of swashplate-type axial piston pumps and motors. The viscosity grades' (VG) effects of oils on power losses are mainly discussed numerically in fluid film lubrication, including changes in temperature and viscosity. The simulation results reveal that the flow rate increases and the friction torque decreases as VG decreases. The film temperature and power loss were minimised for a specific oil with a VG. The minimum conditions regarding the temperature and loss were different and closed. Under various operating conditions, the film temperature and power loss were minimised, suggesting that an optimum hydraulic oil with a specific VG could be selected for given operating conditions of pressure and speed. Otherwise, a preferable operating condition must be established to determine a specific VG oil.

• Polymer(Korea)
• /
• v.32 no.5
• /
• pp.440-445
• /
• 2008

The failure mechanism and failure morphology of linear low density polyethylene (LLDPE) tubing under hydrostatic pressure were investigated. Microscopic observations using video microscope and scanning electron microscope indicate that the failure mode is a brittle fracture including cracks propagated from inner wall to outer wall. In addition, oxidation induction time and Fourier transform infrared spectroscopy results show the presence of exothermic peak and the increase in carbonyl index on the surface of fractured LLDPE tubing, due to thermal-degradation. An accelerated life test methodology and testing system for LLDPE tubing are developed using the relationship between stresses and life characteristics by means of thermal acceleration. Statistical approaches using the Arrhenius model and Weibull distribution are implemented to estimate the long-term life time of LLDPE tubing under hydrostatic pressure. Consequently, the long-term life time of LLDPE tubing at the operating temperature of $25^{\circ}C$ could be predicted and also be analyzed.