• Korean Journal of Food Science and Technology
• /
• v.41 no.1
• /
• pp.32-36
• /
• 2009

The physical properties of freeze-dried Aloe vera gel powders were examined according to the influence of the concentration degrees of the gel solutions as raw materials during freeze-drying. As a pre-treatment prior to freeze-drying, the gel solutions were vacuum-concentrated at three concentration levels (g water/g solids): high (H), 76; medium (M), 119; and low (L), 159. The water contents of the three powder samples were almost the same. For their viscosity measurements, non-Newtonian fluid behavior with shear thinning was observed in samples H and M, whereas Newtonian liquid behavior was found in sample L. In electrical conductivity measurements, sample H showed the highest conductivity upon dissolving the powder in water. For their water sorption isotherms, sample H was analyzed to have the least amount of bound water. Finally, it was determined that the degree of concentration caused only slight differences in the physical properties of freeze-dried Aloe gel powders.

• International Journal of Highway Engineering
• /
• v.1 no.2
• /
• pp.121-133
• /
• 1999

This study was based on the evaluation of 9 asphalts that were produced in five major Korean refineries. The study was concentrated to identify the problems of the current asphalt specification (KS M 2201) and to determine the ranges of visco-elastic asphalt behavior. As a conventional asphalt property. asphalt penetration, ring and ball(R&B) softening point, asphalt viscosity, and flash point of asphalt were measured. Also Dynamic Shear Rheometer (DSR) were used to evaluate visco-elastic properties of asphalts in the $-20^{\circ}C$ through $30^{\circ}C$ temperature range. These properties before and after the short-term (RTFO) and long-term (PAV) aging were compared and analyzed to achieve the research objectives. The conclusion from this study can be summarized by the followings. The low temperature rheological behavior of all the straight asphalt from five major Korean refineries is similar regardless of asphalt grade. In the mean while, the rheological behavior at high and intermediate temperature of Korean straight asphalt varies depending on asphalt grade.

• Journal of Biomedical Engineering Research
• /
• v.25 no.4
• /
• pp.295-300
• /
• 2004

Coil embolization technique has been used recently to treat cerebral aneurysms. When a giant or a multilobular aneurysm are treated by roils, filling an aneurysm sac completely with coils is difficult and partial blocking of an aneurysm sac is inevitable. Blood flow characteristics, which nay affect the embolization process of an aneurysm sac, are changed by the locations of coils for the Partially blocked aneurysms. Blood flow fields are also influenced by the geometry of a parent vessel. In order to suggest the coil locations effective for aneurysm embolization, the blood flow fields of lateral aneurysm models were analyzed for the different coil locations and parent vessel geometries. Three dimensional pulsatile flow fields are analyzed by numerical methods considering non-Newtonian viscosity characteristics of blood. Flow rate into the aneurysm sac (inflow rate) and wall shear stress, which are suspected as flow dynamic factors influencing aneurysm embolization, are also calculated. Inflow rates were smaller and the low wall shear stress zones were larger in the neck blocked models compared to the dome blocked models. Smaller inflow and larger low wall shear stress zones in the distal neck blocked model imply that the distal neck should be the effective coil locations for aneurysm embolization.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.15 no.5
• /
• pp.96-106
• /
• 2011

There are many advantages in applying gel propellant to a gel propulsion system. These include higher performances, the energy management of liquid propulsion system, reliable storability and low leakage characteristics. Additionally, gel propulsion system are preferable to the high density impulse of propulsion system. Also, when compared to liquid propellants, the gel propellants acquire greater heat energy. Gel propellants achieve a high specific impulse when metal particles with aluminum and boron are added. With respect to atomization, an inactive process occurs due to the variable viscosity of the metal particles and gelling agents. To improve the defect of atomization and combustion characteristics of gel propellant, a variety of issues related to spray and combustion is introduced here.

• 한국전산유체공학회:학술대회논문집
• /
• 2001.10a
• /
• pp.51-57
• /
• 2001

The eddy viscosity turbulence models were applied to predict the flows through a cascade, and the prediction performances of turbulence models were assessed by comparing with the experimental results for a controlled diffusion(CD) compressor blade. The original $\kappa-\omega$ turbulence model and $\kappa-\omega$ shear stress transport(SST) turbulence model were used as two-equation turbulence model which were enhanced for a low Reynolds number flow and the Baldwin-Lomax turbulence model was used as algebraic turbulence model. Farve averaged Wavier-Stokes equations in a two-dimensional, curvilinear coordinate system were solved by an implicit, cell-centered finite-volume computer code. The turbulence quantities are obtained by lagging when the men flow equations have been updated. The numerical analysis was made to the flows of CD compressor blade in a cascade at three different incidence angles (40. 43.4. 46 degrees). We found the reversion in the prediction performance of original $\kappa-\omega$ turbulence model and $\kappa-\omega$ SST turbulence model when the incidence angie increased. And the algebraic Baldwin-Lomax turbulence model showed inferiority to two-equation turbulence models.

• Journal of the Korean Graphic Arts Communication Society
• /
• v.29 no.2
• /
• pp.45-58
• /
• 2011

Gravure off-set printing recently is used in electronics display market. This method has advantages of mass production and high printing speed. It is also fine pattern can be implemented. We have manufactured low-curable conductive Ag pastes for gravure off-set printing. When printing, the pastes be used different silver powder shape because of the printing characteristics. The pastes were prepared with silver powder by silver powder shape and size, epoxy resin, solvent and homogenized on a standard three-roll mill. And the pastes exhibited a shear-thinning flow at viscosity profile. Moreover the adhesive strength and resistivity of silver film had a good characteristics. With the manufactured paste in this study, touch panel had is manufactured and it had $4{\times}10-5{\Omega}.cm$.

• Proceedings of the Korea Technical Association of the Pulp and Paper Industry Conference
• /
• 2011.04a
• /
• pp.327-338
• /
• 2011

This study was carried in order to manufacture the high quality coated paper. High quality includes not only properties of coated paper but also final print quality. In this study, new acrylic-styrene emulsion was polymerized in laboratory and compared with styrene-butadiene latex. Low-shear viscosity of coating color was decreased with increasing acrylic-emulsion dosage. WRV was increased with addition and decreased with substitution of acrylic-emulsion. Paper gloss, brightness and whiteness were increased and PPS and opacity was slightly decreased with acrylic-emulsion. Ink gloss was increased with using No. 3 acrylic-emulsion due to lower ink setting properties. However No.1, 2 emulsion shows opposite situation. Surface strength of coated paper was increased with using No. 3 acrylic-emulsion These results indicate that high quality coated paper can be manufactured with using No. 3 acrylic-emulsion.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.44 no.1
• /
• pp.37-42
• /
• 2012

This study was carried in order to manufacture the high quality coated paper. High quality includes not only physical and optical properties of coated paper but also final print quality. In this study, new acrylic-styrene emulsion was polymerized in laboratory and compared with conventional styrene-butadiene latex. Low-shear viscosity of coating color was decreased with increasing acrylic-emulsion dosage. Small amount of acrylic emulsion addition increased water retention, but further addition decreased it. Acrylic-emulsion addition improved paper gloss, brightness and whiteness, but decreased PPS and opacity slightly. Ink gloss was increased with using No. 3 acrylic-emulsion due to lower ink setting properties. However No. 1 and 2 emulsion showed the opposite result. Surface strength of coated paper was increased with using No. 3 acrylic-emulsion. These results indicate that high quality coated paper can be manufactured with using No. 3 acrylic-emulsion.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.45 no.6
• /
• pp.36-43
• /
• 2013

Effects of blending of PCC manufactured with emission gas occurred at mill on the characteristics of coating color, optical and printing properties of coated paper were investigated in order to evaluate the possibility of its use as a raw material for producing environmentally friendly coated paper. Low shear viscosity and water retention value of ground PCC 1(d50 = $6.303{\mu}m$) were higher than those of ground PCC 2(d50 = $3.149{\mu}m$). Ink set properties of ground PCC 1 and ground PCC 2 were inferior to that of PCC 3. Thus, the reducing of particle size was required in order to overcome the inferior ink set properties. Ground PCC 1 had a similar properties to clay, and it showed the possibility that ground PCC 1 could be used to produce matte grade coated papers. However, it was required to improve the stability(particle shape, particle size, and compatibility with chemicals used in coating color formulation) in the case of blending with GCC in order to keep the qualities of coated paper.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.10 no.3
• /
• pp.227-234
• /
• 2022

In this study, the rheological properties of cement paste composites applied with carbon-based nano-materials were experimental analyzed. Flow table and rheological properties, compressive strength were measured in the cement paste using graphene oxide asqueous solution and carbon nanotube aqueous solution. When carbon nano-materials was mixed in an aqueous solution, flow decreased and plastic viscosity and shear stress were increased. In particular, graphene oxide rapidly increased the plastic viscosity and shear stress. In the case of carbon nanotube aqueous solution, when less than 0.2 % was mixed, the increase rate was low compared to graphene oxide. This is because the specific surface area of graphene, which is in the form of a plate, is large. The compressive strength showed a small amount in strength increase when graphene mix, and CNT had a strength about 112 % of OPC. Carbon-based nanomaterials, is considered that CNT are suitable more to be used construction materials. However, extra studies on the surfactant to be used for mixing proportion and dispersion will be needed.