• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.3
• /
• pp.379-386
• /
• 2022

The goal of this research is to verify a performance test system for a low speed, high torque, and harsh reducer at low cost. The reducer rotates a cooling fan with a diameter of 10 meters, in a high temperature (50℃) cooling tower in a geothermal power plant. It requires about 500 kgf·m torque and 47.75 kW power to rotate the fan at a maximum power condition. An expensive dynamometer is commonly used for performance test of a motor or a reducer. In this paper, a low cost system is developed using a hydraulic pump as a load unit to generate torque instead of a dynamometer. We accurately calculated the required power, the flow meter, and the pressure of the pump, and selected to design and optimize the system at minimal cost. The system also applied another reverse reducer and a gearbox to increase the rotational speed and to reduce the torque from the low speed and high torque target reducer. This allows low-cost systems to be built using inexpensive components. The developed system was able to successfully measure the high torque and the low rotational speed of the target reducer at high temperature.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.114.6-114
• /
• 2001

According to expansion of wireless communication system and mobile device, interest has been growing in personal navigation system integrated with wireless system. In portable consumer electronics, such as cellular phones, GPS and PDA, one of major design factors is the power consumption. Solutions of reducing the power dissipation are low voltage, low system clock power management and so on. This paper develops a GPS receiver based on the advanced power management algorithm that achieves very low average power consumption. Both RF and DSP chips are powered down and reactivated only when the position fixing is required. In order to run, the developed includes the RTC calibration function and the fast reacquisition function using XMC (eXtended Multiple Correlator) ...

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.67 no.6
• /
• pp.738-744
• /
• 2018

This paper proposes a low cost hot swap operation circuit of a parallel operation power supply for servers. Hot swap function for server power system is essential in 24 hour operation system such as internet data center, server, factory and etc. Server power supplies used in internet data centers have two or more parallel operations with the hot swap operation. However, the cost of the power supply is high because the controller IC for hot swap operation is very expensive. Therefore, this paper proposes a parallel-operated power supply with a low-cost hot swap controller for servers. The proposed system can operate hot swap function by using discrete devices and reduce the cost by more than 50%. A 1.2kW prototype system is implemented to verify the proposed low cost hot swap controller.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2012.05a
• /
• pp.274-277
• /
• 2012

In this paper, we proposes the design of laundry system for low power and smart management. The low power system configures the network with the RF communication module that turn on/off periodically, power consumption less than operating the module all the time without it toggles. The smart management is RFID Laundry Management System (LMS), in order to provide high services, low operation costs and better monitoring. The proposed system consists of RFID tag, wireless RFID hanger and MFC software. To compare with other existing RFID system, our system was developed as a web application. Therefore, customer can check their cloth status through web page or smartphone devices. RFID reader was designed on hanger to make our system enables reliable running effectively. Some results on the performance of an implementation are presented.

• ETRI Journal
• /
• v.43 no.3
• /
• pp.459-470
• /
• 2021

This paper presents a low-cost prototype for monitoring online the maximum power produced by a domestic photovoltaic (PV) system using Internet of Things (IoT) technology. The most common tracking algorithms (P&O, InCond, HC, VSS InCond, and FL) were first simulated using MATLAB/Simulink and then implemented in a low-cost microcontroller (Arduino). The current, voltage, load current, load voltage, power at the maximum power point, duty cycle, module temperature, and in-plane solar irradiance are monitored. Using IoT technology, users can check in real time the change in power produced by their installation anywhere and anytime without additional effort or cost. The designed prototype is suitable for domestic PV applications, particularly at remote sites. It can also help users check online whether any abnormality has happened in their system based simply on the variation in the produced maximum power. Experimental results show that the system performs well. Moreover, the prototype is easy to implement, low in cost, saves time, and minimizes human effort. The developed monitoring system could be extended by integrating fault detection and diagnosis algorithms.

• The Magazine of the IEIE
• /
• v.25 no.5
• /
• pp.31-41
• /
• 1998

With the advent of portable electronic systems, power consumption has recently become a major issue in circuit and system design. Furthermore, the sophisticated fabrication technology makes it possible to embed more functions and features in a VLSI chip, consequently calling for both higher performance and lower power to deal with the ever growing complexity of system algorithms than in the past. VLSI designers should cope with two conflicting constraints, high performance and low power, offering an optimum trade off of these constraints to meet requirements of system. Historically, VLSI designers have focused on performance improvement, and power dissipation was not a design criteria but an afterthought. This design paradigm should be changed, as power is emerging as the most critical design constraint. In VLSI design, low power design can be accomplished through many ways, for instance, process, circuit/logic design, architectural design, and etc.. In this paper, a few low power design examples, which have been used in 8 bit micro-controller core, and can be used also in 4/16/32 bit micro-controller cores, are presented in the areas of circuit, logic and architectural design. We first propose a low power guidelines for micro-controller design in SAMSUNG, and more detailed design examples are followed applying 4 specific design guidelines. The 1st example shows the power reduction through reduction of number of state clocks per instruction. The 2nd example realized the power reduction by applying RISC(Reduced Instruction Set Computer) concept. The 3rd example is to optimize the algorithm for ALU(Arithmetic Logic Unit) to lower the power consumption, Lastly, circuit cells designed for low power are described.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.11
• /
• pp.1800-1805
• /
• 2016

The micro-grid designed as bipolar ${\pm}750V$ low-voltage DC power distribution system demonstrated by KEPRI, demands interconnection of a number of small decentralized power source including variable renewable generator. Therefore, variable researches for the influence of interconnection with the bipolar typed DC grid and these variable power sources are required for superior quality of power distribution. Renewable power generation simulators for the bipolar ${\pm}750V$ low-voltage DC power distribution system are necessary for such researches. In this paper, we carry out a research on the photovoltaic simulator that be actually able to interconnect with a bipolar ${\pm}750V$ low-voltage micro-grid. Simulator for this research is not only able to simulate photovoltaic generation according to weather informations and PV modules characteristics, but also contribute to stabilization of bipolar ${\pm}750V$ low-voltage of the system. Therefore, the simulator was designed to develop a system that can situationally respond to variable control algorithms such as the MPPT control, droop control, EMS power control, etc.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.18 no.4
• /
• pp.47-54
• /
• 2022

In this paper, MEMS embedded system design implemented the sensor events via analyzing the characteristics that dynamically happened to an abnormal status in power IoT environments in order to guarantee a maintainable operation. We used three kinds of tools in this paper, at first Bluetooth Low Energy (BLE) technology which is a suitable protocol that provides a low data rate, low power consumption, and low-cost sensor applications. Secondly LSM6DSOX, a system-in-module containing a 3-axis digital accelerometer and gyroscope with low-power features for optimal motion. Thirdly BM1422AGMV Digital Magnetometer IC, a 3-axis magnetic sensor with an I2C interface and a magnetic measurable range of ±120 uT, which incorporates magneto-impedance elements to detect the magnetic field when the current flowed in the power devices. The proposed MEMS system was developed based on an nRF5340 System on Chip (SoC), previously compared to the standalone embedded system without bluetooth technology via mobile App. And also, MEMS embedded system with BLE 5.0 technology broadcasted the MEMS system status to Android mobile server. The experiment results enhanced the performance of MEMS system design by combination of sensors, BLE technology and mobile application.

• Journal of IKEEE
• /
• v.22 no.2
• /
• pp.480-483
• /
• 2018

Wireless power transfer (WPT) is the technology that forces the power to transmit electromagnetic field to an electrical load through an air gap without interconnecting wires. This technology is widely used for the applications from low power smartphone to high power electric railroad. In this paper, the model of wireless power transfer circuit for the low power system is designed for a resonant frequency of 13.45 MHz. Also, a feedback WPT circuit to improve the power transfer efficiency is proposed and shown better performance than the original open WPT circuit, and the methodology for power efficiency improvement is studied as the coupling coefficient increases above 0.01, at which the split frequency is made.

• Proceedings of the KIEE Conference
• /
• 2002.11b
• /
• pp.15-19
• /
• 2002

To provide a specified power quality under electric market system is becoming an important issue for customers and utility company. However, there is no realistic infra-structure to design a power system for the specified power quality. Present electric market is operating under the economic point of view. The low price could be attractive. but the effect of low price and low power quality for the long time should be considered for the system safety. This paper presents a model which conceptualize the dynamic power quality control mechanism to minimize total cost of a society which is affected electric power quality. This model aims to produce a basic infra-structure to balance cost and quality under the electric market system.