• 한국광학회지
• /
• 제14권1호
• /
• pp.33-37
• /
• 2003

트렌치 구조를 이용한 저전력 1$\times$2 폴리머 열 광학 스위치를 제안하고 제작하였다. 최적의 위치에 적절히 형성된 트렌치 구조는 전극으로부터 발생한 열 흐름을 방해하여 전력 소보를 줄이는데 기여할 수 있다 광 도파로를 구성하는 폴리머 층에서의 온도 분포가 변하여 Y-분기를 이루는 두 도파로들 사이의 온도 기울기가 급격하게 증가하기 때문이다. 본 실험에서는 트렌치 구조의 효과를 비교 분석하기 위해 트렌치 구조가 없는 1$\times$2 폴리머 열 광학 스위치도 동일한 기판 위에 함께 제작하였다. 트렌치 구조를 이용한 열 광학 스위치의 경우, 측정된 누화는 TE 편광에서 -17.0 dB 이하. TM 편광에서 -15.0 dB 이하였다 전력 소모는 트렌치 구조가 없는 열 광학 스위치의 소모 전력보다 25% 감소한 약 66 ㎽였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2023년도 봄 학술논문 발표대회
• /
• pp.191-192
• /
• 2023

In recent years, the use of high-strength grout has gained popularity in offshore wind power generation complexes for facility foundations and bridges. These marine wind farms require support for horizontal loads from wind and waves. To ensure the strength of the grout produced in environments similar to the actual placing site, this study investigated the curing of high-strength grout discharged through pump pressure in various environments, and examined the difference in strength according to different variables. Compressive strength measurements revealed that the core specimen collected from the bottom (3cm) and uppermost (50cm) of the specimen exhibited lower strength compared to other height specimens, while the core specimen obtained from the corner exhibited lower strength compared to the center. These findings suggest that the strength difference between the center and the corner is more pronounced when curing at low temperatures. This effect is greater than the strength reduction that typically occurs during low-temperature curing, and thus, necessitates careful attention in similar construction environments.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 제4회 압출 및 인발가공 심포지엄
• /
• pp.55-62
• /
• 2001

An electrolytic copper rod was drawn up to $90\%$ in area reduction and annealed under various conditions. The EBSD measurement of the drawn wire showed that in the center region the <111> + <100> fiber duplex texture was dominant, while in the middle and surface regions relatively defused textures developed with a little higher density in <11w>//wire axis. The inhomogeneous texture in the deformed wire gave rise to the inhomogeneous microstructure and texture after annealing. The annealing texture could be classified into the recrystallization texture developed during low temperatures and at the early stage at a high temperature and the growth texture developed after a prolonged annealing at the high temperature. The recrystallization temperature could be explained by the strain energy release maximization model and the growth texture was discussed based on the grain boundary mobility anisotropy.

• 한국에너지공학회:학술대회논문집
• /
• 한국에너지공학회 1992년도 학술발표회 초록집
• /
• pp.35-38
• /
• 1992

The feasibility of magnetohydrodynamic (MHD) Ship propulsion using superconduction magnets is reviewed in light of recent advances in high-temperature superconducting. The propulsion using a screw propeller in the noise reduction has it's own limitation. The epochal noiseless MHD propulsion method which does not have this disadvantage is studying nowadays. The subject of a marine MHD as propulsion has been examined before and was found to be interesting because of relatively low magnetic flux densities. It is demonstrated that the MHD propulsion is technically interesting with high magnetic flux density. The development of large-scale magnets using the high-temperature superconductors now under development could make it practical to construct submersibles for high-speed and silent operation.

• Macromolecular Research
• /
• 제13권1호
• /
• pp.68-72
• /
• 2005

A low-molecular-weight poly(lactic acid) was synthesized through the condensation reaction of L-lactic acid. The effects that the catalyst and temperature have on the reaction rate were studied to determine the optimum reaction conditions. The reaction kinetics increased with temperature up to $210^{\circ}C$, but no further increase was observed above this temperature. Among a few selective catalysts, sulfuric acid was the most effective because it maximized the polymerization reaction rate. Reduction of the pressure was another important factor that enhanced this reactions kinetics.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.10-16
• /
• 2004

The Homogeneous Charge Compression Ignition (HCCI) engine has advantage for reducing the NOx and P.M. simultaneously. Therefore, HCCI engine is receiving attention as a low emission diesel engine concept. This study was carried out to investigate the characteristics of combustion and exhaust emission for operating conditions in a direct injection type of HCCI engines such as supercharged and naturally aspirated using diesel fuel and additive. From the experimental result, we found that cool flame was always appeared and also it was difficult to control combustion characteristics by changing the injection timing in HCCI. In addition, at the lean air-fuel ratio and high speed range, it was observed that charging air pressure, additive or increasing intake air temperature is effective to increase combustion performance and reduce exhaust emission. We concluded that chemical reaction by the increasing intake air temperature or additive without physical improvement has limitation for reduction of exhaust emission.

• 한국수소및신에너지학회논문집
• /
• 제27권6호
• /
• pp.727-736
• /
• 2016

Numerical simulations of n-heptane spray characteristics in a constant volume combustion chamber under diesel engine like conditions with increasing ambient gas density ($14.8-142kg/m^3$) and ambient temperature (800-1000 K) respectively were performed to understand the non-vaporizing and vaporizing spray behavior. The effect of fuel temperature (ranging 273-313 K) on spray characteristics was also simulated. In this simulation, spray modeling was implemented into ANSYS FORTE where the initial spray conditions at the nozzle exit and droplet breakups were determined through nozzle flow model and Kelvin-Helmholtz/Rayleigh-Taylor (KH-RT) model. Simulation results were compared with experimentally obtained spray tip penetration result to examine the accuracy. In case of non-vaporizing condition, simulation results show that with an increment of the magnitude of ambient gas density and pressure, the vapor penetration length, liquid penetration length and droplet mass decreases. On the other hand vapor penetration, liquid penetration and droplet mass increases with the increase of ambient temperature at the vaporizing condition. In case of lower injection pressure, vapor tip penetration and droplet mass are increased with a reduction in fuel temperature under the low ambient temperature and pressure.

• 한국조경학회지
• /
• 제47권6호
• /
• pp.67-77
• /
• 2019

본 연구는 미세먼지 문제가 심각한 도심에서 도시근린공원의 중심이 입구에 비해 어느 정도 저감된 공간인지 분석해 보는데 목적이 있다. 또한 공원중앙의 공간 차폐율과 미세먼지 저감율과의 상관관계를 실험을 통해 도출해 내고자 하였다. 대구시 수성구 평지형 도시근린공원 7개를 대상으로 3일동안 같은 장소에서 측정하였다. 연구결과, 첫째, 도시근린공원 중심은 입구보다 온도는 평균 1.05℃ 낮고, 습도는 평균 2.57% 높았다. 둘째, 미세먼지 감소율은 PM1 17.09%, PM2.5 17.65%, PM10 14.99%의 저감율로 초미세먼지가 더 높은 것으로 분석되었으며, 공원의 규모가 작을수록 저감효과가 더 높았다. 또한 기상청발표 미세먼지 농도가 높은날일수록 공원중앙에서의 저감율은 낮았으며, 공원입구의 농도가 높을수록 저감율은 높았다. 셋째, 공원중심에서 공간차폐율이 높을수록 미세먼지 저감효과가 높은 것으로 파악되었다. 도시근린공원의 미세먼지 저감정도와 공간차폐율과의 상관관계를 파악할 수 있었으며, 더 확대된 실험데이터들의 기초가 되기를 기대한다.

• 환경위생공학
• /
• 제22권1호
• /
• pp.1-16
• /
• 2007

The incineration process has commonly used for wastes amount reduction and thermal treatments of pollutants as the technologies accumulated. However, the process is getting negative public images owing to matter of hazardous pollutants emission. Specially dioxins became a main issue and is mostly emitted from municipal solid wastes incineration. In this reason, pyrolysis/gasfication/melting process is presented as a alternative of incineration process. The pyrolysis/gasfication/melting process, a novel technology, is middle of verification of commercial plant and development of technologies in Korea. But the survey about the pollutant emission from the process, and background data in these facilities is necessary. So in this survey, it Is investigated that the behavior of dioxins in three pyrolysis/gasfication/melting plant (S, T, P) of pilot scale. In case of S plant, concentration of dioxins shows high at latter part of cogenerated boiler and stack which are operate on low temperature conditions than a latter parts of pyrolysis and melting furnace which are operate on high temperature condition. Concentration of gas phage dioxins had increased after combusted gas passed cogenerated boiler and this is attributed to react of precursor materials such as chlorobenzene and chlorophenol. Concentration of dioxins in T plant showed lower levels at latter part of cooling equipment which are operate with water spray type on low temperature conditions than a latter parts of gasfied melting furnace which are operate on high temperature condition. Removal efficiency of dioxins at gas treatment equipment was 78.8 %. Concentration of dioxins in P plant was low at latter part of SDA/BF which is operate at low temperature conditions than a latter parts of pyrolysis gasfied chamber which are operate at high temperature condition. Removal efficiency of dioxins of SDA/BF was 85.9 % and therefore, it showed high efficiency at those of stoker type incineration facility. However, concentration of dioxins which emitted at high temperature condition were low in three facilities and satisfied present standard emission level of dioxins. To consider the distribution ratio of dioxins, Particulate phase dioxins at S and P plants showed similar ratio with which shows in current stoker type for middle scale domestic waste incineration facility. It is necessary to continuos monitoring the ratio of distribution of dioxins in T plant in because ratio of gas phage dioxins showed high.

• 한국산업융합학회 논문집
• /
• 제9권1호
• /
• pp.13-19
• /
• 2006

The ozone produced by a dielectric barrier discharge device was injected into the exhaust gas to oxidize a part of NO to $NO_2$, and then the exhaust gas containing the mixture of NO and $NO_2$ was further treated in a catalytic reactor where both NO and $NO_2$ were reduced to $N_2$ in the presence of ammonia as the reducing agent. The $NO_2$ content in the mixture of NO and $NO_2$ was changed by the amount of ozone added to the exhaust gas. The experiments were primarily concerned with the effect of reaction temperature on the catalytic $NO_x$ reduction at various $NO_2$ contents. The increase in the $NO_2$ content by the ozone injection remarkably improved the performance of the catalytic $NO_x$ reduction, especially at low temperatures.