• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.111-116
• /
• 1997

In this paper, the limit temperature for applying maturity method are discussed. 4 kinds of W/C in combination of 7kinds of curing temperature are selected as experimental parameters. According to the experimental results, high curing temperature and low W/C gain in strength rapidly. And maturity rule can be applied less than $30^{\cire}C$ in W/C of 30~60% in the conditions of this experiment.

• 한국건축시공학회지
• /
• 제18권3호
• /
• pp.267-275
• /
• 2018

본 논문은 알칼리활성화 슬래그 레드머드 시멘트의 백화저감을 위한 기초연구로서 다양한 온도 및 습도 조건이 레드머드 혼입 알칼리활성화 슬래그 시멘트의 강도 및 백화에 미치는 영향을 보통 포틀랜트 시멘트와 비교하여 검토하였다. 양생조건에 따른 레드머드 혼입 알칼리활성화 슬래그시멘트의 강도 및 백화특성 검토결과 표준수중양생을 실시한 모르타르는 기건양생, 고온양생, 저온양생과 비교하여 28일 압축강도, 휨강도가 가장 높게 나타났으며 흡수율 및 백화발생면적, $Na^+$용출량은 가장 낮게 나타났다. 따라서 향후 레드머드의 대량 활용을 위한 방안으로서 적정한 양생조건은 수중양생으로 사료된다.

• 한국연초학회지
• /
• 제20권1호
• /
• pp.13-18
• /
• 1998

In the flue curing process, the wet bulb temperature is usually controlled at a constant level. To improve the quality of flue cured leaves, we studied the effect of the cyclic change of wet bulb temperature at the yellowing stage of flue curing on physical properties of cured leaves. The wet bulb temperature was automatically controlled between preset high (38℃) and low point (35℃) every one hour cyclically. As a result, the acceleration of the increase in the physical properties of cured leaves were observed. The leaves cured by this method were more or less orange in color, better bodied, and less brittle compared with the leaves produced by conventional curing. However, the leaves cured by this method had a little sharpness and harshness. As to the physical properties, there was decreased in occurrence of flat leaves than that of conventional ones. On the other hand, in case of cyclic curing method, increase of price per kg reached to 2-3% compared with those of conventional ones.

• 한국건축시공학회지
• /
• 제2권2호
• /
• pp.151-156
• /
• 2002

When fresh concrete is exposed to low temperature, the concrete may suffer frost damage due to freezing at early ages and strength development may be delayed. One of the solution methods for resolve these problems is to reduce freezing temperature of concrete by the use of chemical admixture called Accelerators for freezing resistance. In this study, we investigate the effect on strength development of cement mortar using accelerators for freezing resistance with the variance curing condition. As the result of this study, the mortar using accelerators for freezing resistance show that continuously strength development in curing condition of -5$^{\circ}C$. And compressive strength under the variance temperature condition was higher than constant temperature condition in same maturity.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2010년도 춘계 학술논문 발표대회 1부
• /
• pp.71-72
• /
• 2010

The study is compared temperature history and strength of concrete followed by covering method of insulation curing of cold weather concrete with double bubble sheet. The results were as follows. First of all, in temperature history of concrete, the internal temperature of concrete fell down to $0^{\circ}C$ before/after 60 hours, having nothing to do with covering method. The study could see that, when sheet was isolated, it fell down to low temperature quickly in early curing. When the study measured compressive strength of core specimen, there were no large differences among placing methods. However, compressive strength fell down in all ages when sheet was isolated.

• 한국재난정보학회 논문집
• /
• 제2권1호
• /
• pp.129-137
• /
• 2006

The present work is attempt to evaluate the temperature dependence of blast furnace slag concrete(BFSC) based on the concrete strength cured with different curing temperatures and ages. A equivalent substitution index(ESI) was induced to explain temperature dependence of concrete quantitatively as well as concrete strength. The results from compressive strength showed substantial crossover effect. which is the phenomenon that the compressive strength cured at low temperature becomes stronger than the one cured at high temperature. The crossover effect found more definitely on BFSC than plain concrete.. The ESI became 1.1 and 1.0 for the BFSC cured at $20^{\circ}C$ and $30^{\circ}C$ after age of 56 days, respectively. Which means that the contribution to strength development of blast furnace slag per unit mass is stronger than that of the Portland cement. It was considered therefore that the optimum curing temperature for BFSC is $20^{\circ}C$.

• 한국축산식품학회지
• /
• 제23권1호
• /
• pp.32-38
• /
• 2003

식염농도 7%의 염지액을 이용하여 돼지고기 등심을 염지할 때에 염지온도와 기간이 염지육의 이화학적 특성과 기호성에 미치는 영향을 검토하였다. 열지온도 1$0^{\circ}C$에서 15일째에 염지육의 pH와 보수력이 현저히 저하되었다. 염지온도 1$0^{\circ}C$에서 염지액과 염지육 표면부위의 일반세균수는 12째에 현저히 많아졌으나 중심부위는 거의 검출되지 않았다. 임시 온도가 높을수록 염지기간에 관계없이 식염 침투가 빠르고 염지육 식염함량이 많아졌으며, 표면부위에 대한 중심분위의 식염함량 비율은 염지기간이 길수록 크게 나타났다. 염지육의 식염함량은 가열에 의하여 적어졌다. 염지 가열육의 짠맛과 풍미는 염지 초기에는 높은 온도에서, 후기에는 낮은 온도에서 우수하였다. 열지 가열육은 1$^{\circ}C$에서 12일, 5$^{\circ}C$에서 9일 염지하여 제조하면 기호성이 우수하였다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 춘계 학술논문 발표대회 1부
• /
• pp.83-85
• /
• 2011

This study investigated the results of insulation heat curing method using double layer bubble sheet in concrete in cold weather environment. First of all, when double bubble sheets are applied, it was shown that concrete was protected from early freezing by remaining between 7℃ and 3℃ even in case outside temperature drops -7℃ below zero until the 3d day from piling. The insulation heat preservation curing method using the double bubble sheet applied in this field prevented early freezing owing to stable curing temperature management, deterring concrete strength development delay at low temperature, and obtained the needed strength. Also, it was proven that the method is highly effective and economic for cold weather concrete quality maintenance through curing cost reduction like construction period shortening and labor cost reduction, etc by reducing the process of temporary equipment installation and disassembling.

• 한국건축시공학회지
• /
• 제12권3호
• /
• pp.291-298
• /
• 2012

For cold weather concreting, frost damage at early age is generated in the concrete, and problems such as delaying of setting and hardening and lowering of strength manifestation emerge due to the low outside air temperature at the early stage of pouring, making the selection of an effective curing method critically important. Unfortunately, the tent sheet currently used as the curing film for heating insulation at work sites, not only has the problems of inferior permeability and extremely deteriorated airtightness, but a phenomenon of continuous fracturing is also generated along the direction of fabric of the material itself, presenting difficult circumstances for maintaining adequate curing temperature. The aim of this study was to develop an improved bubble sheet type curing film for heating insulation of cold weather concrete by combining mesh-tarpaulin, which has excellent tension properties, with bubble sheet, which offers superior insulation performance. The analysis showed that the improved curing film in which BBS1 is stacked to MT was a suitable replacement for curing films currently in use, as it has better permeability, tension property, and insulation performance than the T type film used at work sites today.

• 한국재료학회지
• /
• 제13권1호
• /
• pp.18-23
• /
• 2003

Properties of Ag thick films fabricated by using low temperature curable silver pastes were investigated. Ag pastes were consisted of polymer resins and silver powders. Ag pastes were used for conductive or fixing materials between board and various electrical and electronic devices. Low temperature curable Ag pastes have some advantages over high temperature curable types. In cases of chip mounting, soldering properties were required for screen printed Ag thick films. In this study, four types of Ag pastes were fabricated with different compositions. Screen printed Ag thick films on alumina substrates were fabricated at various curing temperatures and times. Thickness, resistivity, adhesive strength and solderability of fabricated Ag thick films were characterized. Finally, Ag thick films produced using Ag pastes, sample A and B, cured at $150^{\circ}C$ for longer than 6 h and $180^{\circ}C$ for longer than 2 h, and $150^{\circ}C$ for longer than 1 h and $180^{\circ}C$ for 1 h, respectively, showed low resistivities of $10^{-4}$ $∼10^{-5}$ Ωcm and good adhesive strength of 1∼5 Mpa. Soldering properties of those Ag thick films with curing temperatures at solder of 62Sn/36Pb/3Ag were also investigated.