• 한국재료학회지
• /
• 제33권12호
• /
• pp.537-549
• /
• 2023

The sintering shrinkage behaviors of low temperature cofired ceramics (LTCC) and resistors were compared using commercial LTCC and thick-film resistor pastes, and factors influencing the camber of cofired resistor/LTCC bi-layers were also investigated. The onset of sintering shrinkage of the resistor occurred earlier than that of LTCC in all resistors, but the end of sintering shrinkage of the resistor occurred earlier or later than that of LTCC depending on the composition of the resistor. The sintering shrinkage end temperature and the sintering shrinkage temperature interval of the resistor increased as the RuO₂/glass volume ratio of the resistor increased. The camber of cofired resistor/LTCC bi-layers was obtained using three different methods, all of which showed nearly identical trends. The camber of cofired resistor/LTCC bi-layers was not affected by either the difference in linear shrinkage strain after sintering between LTCC and resistors or the similarity of sintering shrinkage temperature ranges of LTCC and resistors. However, it was strongly affected by the RuO₂/glass volume ratio of the resistor. The content of Ag and Pd had no effect on the sintering shrinkage end temperature or sintering shrinkage temperature interval of the resistor, or on the camber of cofired resistor/LTCC bi-layers.

• 한국분말야금학회:학술대회논문집
• /
• 한국분말야금학회 2006년도 Extended Abstracts of 2006 POWDER METALLURGY World Congress Part2
• /
• pp.1218-1219
• /
• 2006

The shrinkage variation of Low Temperature Cofired Ceramics(LTCC) limits the size of the substrates that impose limitations on embedded passive components. This paper focuses on the method of minimizing or controlling planar shrinkage and reducing distortion during firing. The laminated sheets of alumina and glass were sintered at varying temperature, and depending on the amount of the glass ceramics. When the sintered of multi-layer structure with $Al_2O_3/Glass/Al_2O_3$, the glass infiltrated entirely into $Al_2O_3$ layer at the temperature of about $950^{\circ}C$ or higher.

• 한국세라믹학회지
• /
• 제36권5호
• /
• pp.490-496
• /
• 1999

The sintering behavior of LTCC (low temperature cofired ceramics) chip couplers was investigated in relation with Ag diffusion at the interface of glass ceramic substrate-Ag electrode. Sintering temperature was in the range of 825$^{\circ}C$-975$^{\circ}C$. The commercial green sheet and silver electrode were used. Below 875$^{\circ}C$ the diffusion of the Ag ion into the substrate and the penetration of glassy phases into the electrode occurred due to an increase of fluidity. Thus the lectrode line was severely deformed and damaged. At 975$^{\circ}C$ the transformation of crystalline phases into glassy phases and the melting of the Ag electrode resulted in the diffusion of the considerable amount of Ag ions.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2004년도 춘계학술대회 발표 논문집
• /
• pp.234-239
• /
• 2004

본 연구에서는 마이크로파용 유전재료로서 널리 사용되고 있는 BNT($BaO-Nd_{2}O_{3}-TiO_{2}$)계 세라믹스를 기본조성으로 하고, 저융점의 phoshpate계 유리 프릿의 첨가를 통해 LTCC(Low Temperature Cofired Ceramic)에 적용 가능한 유전율을 가진 조성을 개발 하고자, $70P_{2}O_{5}-5B_{2}O_{3}-(25-x)BaO-xNa_{2}O$ 유리를 제조 및 특성을 평가하였다. 또한, BNT계 세라믹스에 glass frit을 5 - 15 wt% 범위에서 첨가하고, $800 - 950^{\circ}C$의 온도범위에서 소결하여 제조된 유리-세라믹 복합체의 소결특성 및 유전특성을 조사하였다.

• 한국전기전자재료학회논문지
• /
• 제19권5호
• /
• pp.417-421
• /
• 2006

In this study, in order to develop low temperature sintering piezoelectric ceramics for LTCC (Low-Temperature Cofired Ceramic) multilayer piezoelectric actuator, PMW-PMN-PZT ceramics using $0.2wt%\; Li_2CO_3$ and $0.25wt%\;CaCO_3$ as sintering aids were investigated according to the varation of PMW substution. Composition ceramics could be sintered at $900^{\circ}C$ by adding sintering aids. As the amount of PMW substitution increased, the crystal structure of PMW-PMN-PZT ceramics moved from tetragonal phase to rhombohedral phase gradually, and MPB(Morphotrophic Phase Boundary) region appeared at 2 mol% PMW substitution. At the sintering temperature of $900^{\circ}C$, the density, electromechanical coupling factor(kp), mechanical quality factor(Qm), dielectric constant(${\epsilon}r$), piezoelectric constant(d33) and Curie temperature(Tc) of 2 mol% PMW substituted PMW-PMN-PZT ceramics showed the optimal values of $7.88g/cm^3$, 0.58, 1002, 1264, 352 pC/N and $336^{\circ}C$, respectively, for LTCC multilayer piezoelectric actuator application.

• 한국전자파학회지:전자파기술
• /
• 제12권3호
• /
• pp.25-34
• /
• 2001

이동통신용 유전체 필터에 사용되는 유전체 재료 는 많이 상용화 되어 있다. 그러나 향후 IMT2000, BIuetooth. Wireless LAN등에 채용될 부품은 더욱 소형화로 여기에 필요한 새로운 유전체 재료가 요 구된다. 이러한 필터는 결국 적층 일체형 필터의 제작이 대두되고 이를 위해서는 높은 유전율에 높은 Q값을 갖는 저온소결(900˚C이하)재료가 필요하다. 본고에서는 저온소결이 가능한 BiNbO$_{4}$,재료를 갖고 설계, 적층공정 등을 통하여 적층일체형 필터를 제 작하였다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 하계학술대회 논문집 Vol.5 No.2
• /
• pp.574-577
• /
• 2004

A coupler is a microwave passive component used for power coupling or dividing. Regarding the trend of current telecommunication systems it is highly desirable for monolithic integration of passive components as such LTCC(Low temperature cofired ceramics) technology offers potential advantage in size, cost and performance. Utilizing LTCC technology a 2012 size type dual band coupler for DCS and EGSM band was fabricated. Its characteristics such as coupling, insertion loss, isolation and directivity was measured and compared with simulation results

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2004년도 추계학술대회 논문집 Vol.17
• /
• pp.392-395
• /
• 2004

A coupler is a microwave passive component used for power coupling or dividing. Regarding the trend of current telecommunication systems it is highly desirable for monolithic integration of passive components as such LTCC(Low temperature cofired ceramics) technology offers potential advantage in size, cost and performance. Utilizing LTCC technology a 1608 size type dual band coupler for DCS and EGSM band was fabricated. Its characteristics such as coupling, insertion loss, isolation and directivity was measured and compared with simulation results.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2006년도 하계학술대회 논문집 Vol.7
• /
• pp.288-289
• /
• 2006

We studied the effect of sol-gel processing and sintering temperature on the microwave properties of $MgCo_2(VO_4)_2$ system(MCV) which is applicable to LTCC(low-temperature cofired ceramics). The MCV was synthesized by sol-gel process using solution that contains precursor molecules for Mg, Co, and V. SEM analysis shows that the average particle size is ${\sim}1{\mu}m$ and size distribution is very uniform compared to the one prepared by conventional solid-state reaction process. Highly dense samples were obtained at the sintering temperature range of $750^{\circ}C{\sim}930^{\circ}C$. The maximum $Q{\times}f_0$ value of 55,700GHz, dielectric constant(${\varepsilon}_r$) of 10.41 and temperature coefficient(${\tau}_f$) of $-85ppm/^{\circ}C$ was obtained at the sintering temperature of $930^{\circ}C$. The superior microwave properties of sol-gel processed MCV relative to conventional solid-state reaction processed one is remarkable especially at lower sintering temperatures such as $750^{\circ}C$ and $800^{\circ}C$.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.289-291
• /
• 2003

This paper deals with the design of a spiral micro inductor using LTCC(Low Temperature Cofired Ceramics) technology. The inductors using the LTCC technology have some prominent properties of high integration of circuits, high confidence and low cost comparing with previously fabricated thick-film inductors. In this paper, we designed a new spiral-type micro inductor comprising a magnetic material to improve the inductance and leakage flux. we, in addition, presented the simulation results for various shapes of the magnetic material in the micro inductor, Finally application of the micro inductor to the boost DC-DC converter is investigated.