• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.33 no.4A
• /
• pp.352-360
• /
• 2008

Recently Task Group (TG) 4 of the Institute of Electrical and Electronics Engineers (IEEE) 802.15a has been recommended a system with ranging capability in existence of multiple Simultaneous operating piconets (SOPs) as well as low-cost, low-power. According to the ranging service, coherent and non-coherent based ranging schemes using ternary code have been adopted as a standard. However it is hard to estimate an accurate time of arrival (TOA) in case of using direct sequence based TOA estimation method because pulse repetition interval (PRI) offered by TG is more limited than the maximum excess delay (MED) of channel. To mitigate inter pulse interference (IPI) problem, this paper proposes a non-coherent TOA estimation scheme using non-periodic transmission (NPT) pattern. The proposed receiver is based on a non-coherent energy detection considering with motivation of low rate wireless personal area network (LR-WPAN). TOA information is estimated via proper comparison with a prescribed threshold after the sliding correlation and search back window (SBW) process for reducing TOA error. To verify the performance of proposed ranging scheme, two distinct channel models approved by IEEE 802.15.4a TG are considered. According to the simulation results, we could conclude that the proposed scheme have performed better performance than the conventional method on the existence of multiple SOPs.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.30 no.11A
• /
• pp.1027-1034
• /
• 2005

IEEE802.15.4a, which is started to realize the PHY layer including high precision ranging/positioning and low data rate communication functions, requires a simple and low power consumable transceiver architecture. To satisfy this requirements, the simple noncoherent on-off keying (OOK) UWB transceiver with the parallel energy window banks (PEWB) giving high precision signal processing interface is proposed. The flexibility of the proposed system in multipath fading channel environments is acquired with the pulse and bit repetition method. To analyze the bit error rate (BER) performance of this proposed system, a noise model in receiver is derived with commonly used random variable distribution, chi-square. BER of $10^{-5}$ under the line-of-sight (LOS) residential channel is achieved with the integration time of 32 ns and signal to noise ratio (SNR) of 15.3 dB. For the non-line-of-sight (NLOS) outdoor channel, the integration time of 72 ns and SNR of 16.2 dB are needed. The integrated energy to total received energy (IRR) for the best BER performance is about $86\%$.

• Bulletin of the Korean Chemical Society
• /
• v.35 no.5
• /
• pp.1485-1490
• /
• 2014

We have designed and developed a new ladder type tetrafused ${\pi}$-conjugated building block such as dihydroindolo[3,2-b]indole (DINI) and investigated its role as an electron rich unit. The photovoltaic properties of a new semiconducting ${\pi}$-conjugated polymer, poly[[5,10-bisoctyl-5,10-dihydroindolo[3,2-b]indole-[5,6- bis(octyloxy)-4,7-di(thiophen-2-yl)benzo[c][1,2,5]thiadiazole]], represented by PDINI-OBTC8 are described. The new polymer PDINI-OBTC8 was synthesized in donor-acceptor (D-A) fashion, where fused ${\pi}$-conjugated tetracyclic DINI, and 5,6-bis(octyloxy)-4,7-di(thiophen-2-yl) benzo[c][1,2,5]thiadiazole (OBTC8) were employed as electron rich (donor) and electron deficient (acceptor) moieties, respectively. The conventional bulk heterojunction (BHJ) device structure ITO/PEDOT:PSS/PDINI-OBTC8:PCB71M/LiF/Al was utilized to fabricate polymer solar cells (PSCs), which comprises the blend of PDINI-OBTC8 and [6,6]-phenyl-$C_{71}$-butyric acid methyl ester ($PC_{71}BM$) in BHJ network. A BHJ PSC that contain PDINI-OBTC8 delivered power conversion efficiency (PCE) value of 1.68% with 1 vol% of 1,8-diidooctane (DIO) under the illumination of A.M 1.5G 100 $mW/cm^2$.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.43 no.12 s.354
• /
• pp.40-46
• /
• 2006

Latching optical switches and optical logic gates AND and OR are demonstrated, for the first time, by the monolithic integration of a vertical cavity lasers with depleted optical thyristor structure, which have not only a low threshold current with 0.65mA, but also a high on/off contrast ratio more than 50dB. By simple operating technique with changing a reference switching voltage, this single device operates as two logic functions, optical logic AND and OR. The thyristor laser fabricated using the oxidation process achieved a high optical output power efficiency and a high sensitivity to the optical input light.

• The KIPS Transactions:PartD
• /
• v.10D no.3
• /
• pp.359-366
• /
• 2003

Although the reuse of the cached data for scrolling the map reduces the amount of passed data between client and server, it needs the conversions of data coordinates, selective deletion of objects, cache compaction and object structuring step in the clients. The conversion is a time- intensive operation due to limited resources of mobile phones such as low computing power, small memory. Therefore, in order to control the map efficiently in the vector map service based mobile phones, it is necessary to study the methods which reuse cached objects for reducing wireless network bandwidth and overwhelming the limited resources of mobile phones as well. This paper proposes the methods of reusing pre-received spatial objects for map control in the mobile vector map service system based on client-server architecture. The experiments conducted on the Web GIS systems with real data show that the proposed method is appropriate to map services for mobile phone. We also analyze the advantages and drawbacks between the reuse of cached data and transmission of raw data respectively.

• KIISE Transactions on Computing Practices
• /
• v.23 no.2
• /
• pp.116-121
• /
• 2017

In wireless sensor networks, the multipath prefers energy efficient routing method due to the characteristic of low-power sensor which uses geographic method to transmit data packet through information of the neighbor nodes. However, when multipath meets the routing fail area called hole area, path overlap problem can occur, resulting in failed maintenance of disjoint multipath. To solve this problem, multipath research studies have been performed to exploit the modeling and detouring method in routing fail area by keeping the disjoint multipath. However, in an energy point of view, additional method like modeling can lead to a lot of energy consumption of sensor node. Moreover, lots of energy consumption of sensor node can shorten the life span of sensor network. In this study, we proposed an energy efficient geographic routing by keeping the disjoint multipath in routing fail area. The proposed scheme exploited the face routing using the geographic recovery method without additional method like modeling.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.20 no.2
• /
• pp.15-19
• /
• 2012

Wood wastes could be renewable resources by recycling as particleboard manufacturing or energy production. Particle board is the most common item of wood waste recycling and energy production from wood wastes has highlighted for energy recovery to reduce greenhouse gas generation in recent years. The aim of this study was to evaluate the environmental benefits of the processes for particle board manufacturing and energy production. The functional unit was one ton of wood wastes and the environmental impact was analyzed by life cycle assessment methodology. The result was that 112kg of carbon dioxide equivalent was produced from particle board manufacturing process and 382kg of carbon dioxide equivalent was produced from combined heat and power generation process. The concept of temporary biomass carbon storage was to applied to this study.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.14 no.6
• /
• pp.1-6
• /
• 2014

The IoT (Internet of Things) is considered as a core technology to realize interconnected world. At this, companies composing ICT industry and standard organizations make efforts to accelerate it. IETF CoRE(Constrained RESTful Environment) working group standardized CoAP (Constrained Application Protocol) for the constrained device. CoAP has RESTful architecture and CoAP option is provided to use forward-proxy. The forward-proxy is used to translate protocol and perform requests on behalf of the client. However, communication between Internet based client and LLN(Low-power and Lossy Network) based CoAP server architecture has limitations to deploy real IoT service. In this architecture, problems like response delay, URI assignment and DoS attack can be occurred. To solve these problems, we propose the reverse-proxy based system. We consider both of static IoT and mobility IoT environments. Finally, our proposed system is expected to provide efficient IoT service.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.12 no.1
• /
• pp.209-218
• /
• 2017

Healthcare services can be provided through a number of independent service platforms for measurement of vital signs, diagnosis and prevention of diseases, and Information and communication technology(ICT) such as internet and mobile are converged to provide health information to users at anytime and anywhere, and it is in the center of the IoT(Internet of things). Accordingly, in this paper, we designed IoT based urination management system and evaluate the performance. A low - power Zigbee network was constructed for the configuration of the urination management system. The implemented capacitive diaper sensor was operable for the duration of 2,000 hours. We also built a database server using Raspberry Pi, a tiny embedded device, and stored the collected data to verify the data through an Android-based mobile application. The proposed urination management system can be utilized not only for the older patients, but also for the infants.

• Journal of the Korean Society of Costume
• /
• v.50 no.4
• /
• pp.181-195
• /
• 2000

This study was conducted from Sep., 1999. to Nov., 1999. It researched approximately 60 specialized manufacturers who had homepages on the Internet. Of the 60 manufacturers, 20 of them were chosen for the study all of whom had relatively were made homepages that were geared towards sales. 1. Daily Hanboks on the homepages were put in an electronic catalog. They were photographed and well described. Each picture could be enlarged when needed. 2. The Hanbok's were made for men, women and children. There were every couple's Hanboks. The Hanboks used natural material, mixed spinning and chemical textile, which was easily kept and washed. It was intended, as clothes for everyday wear Silk was used for formal clothes. 3. The prices ranged from low-middle to high clothing for everyday life is reasonable and street wear and formal dresses are priced high. The color of the dresses are not vibrant, but natural and light. As Hanboks become more in demand, there will be more choices available. 4. As matter of the sizes shows weakness. In general they use the western size system. The purpose of this study is to show the direction that Hanbok manufacturers may take for the internet sales and for being more active to promote the spread of the dress. This research came to the fellowing conclusion. Even though Hanbok manufacturers operate homepages. it seems that they are not well used. However, many internet shopping malls have been opened and they have put Daily Hanboks into one of their sales categories. The internet malls are getting more active and are expanding more. Therefore the market value of the Hanboks in the future look optimistic. If smaller sized manufacturers of Daily Hanbok's establish cooperative network that have no time and space limit, they can use the strong power of the market as the market development for Daily Hanboks is endless.