• Transactions of the Korean Society of Mechanical Engineers
• /
• v.13 no.2
• /
• pp.252-256
• /
• 1989

In the low cycle fatigue fracture testing with KS(or JIS) SS41, crack growth rate, AE count rate and J-integral range are measured to get empirical relations between crack growth rate and J-integral range, AE count rate and J-integral range as well as AE count rate and crack growth rate. All the relations are shown to be linear on the log-log graphs. It is also shown that the linear relations can be formulated by using Dunegan's assumption and elastic-plastic fracture mechanics along with the well-known relation of crack growth rate and J-integral range. It is concluded that the differences between experimental and theoretical values are due to Dunegan's assumption.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.5
• /
• pp.12-19
• /
• 2000

The increasing use of vehicles is causing air-pollution problems. Diesel vehicles are preferred to gasoline vehicles, because the diesel vehicles are superior to gasoline vehicles in terms of fuel consumption, durability, power and efficiency. But the emission reduction technologies for diesel vehicle are not developed well like those for gasoline vehicles. Moreover, the NOx and smoke emitted from diesel vehicle are recognized as a main source of the air-pollution in the urban areas. The emission reduction devices have been installed for each of the emission gas components. Using plasma(i.e. electrical energy)only, the emission gas was found to be reduced. The present paper investigate the effects of a low temperature plasma device in engine performance as well as in emission reduction with the change of the applied voltage and the loading rate of the engine.

• International Journal of Fluid Machinery and Systems
• /
• v.4 no.1
• /
• pp.97-103
• /
• 2011

With the aim to increase blade loadings and stable operating range in highly loaded compressors, this article has been conducted to explore, through a numerical parametric study, the potential of passive control using slotted bladings in cascade configurations. The objective of this numerical investigation is to analyze the influence of location, width and slope of the slots and therefore identify the optimal configuration. The approach is based on two dimensional cascade geometry, low speed regime, steady state and turbulent RANS model. The results show the efficiency of this passive technique to delay separation and enhance aerodynamic performances of the compressor cascade. A maximum of 28.3% reduction in loss coefficient have been reached, the flow turning is increased with approximately $5^0$ and high loading over a wide range of angle of attack have been obtained for the optimized control parameter.

• Structural Engineering and Mechanics
• /
• v.6 no.1
• /
• pp.95-113
• /
• 1998

The extensive use of honeycomb sandwich structures has led to the need to understand and analyze their low velocity impact response. Commercially available finite element software provides a possible analysis tool for this type of problem, but the validity of their material properties models for honeycomb materials must be investigated. Three different problems that focus on the effect of differences in honeycomb material properties on static and dynamic response are presented and discussed. The first problem considered is a linear elastic static analysis of honeycomb sandwich beams. The second is a nonlinear elastic-plastic analysis of a circular honeycomb sandwich plate. The final problem is a dynamic analysis of circular honeycomb sandwich plates impacted by low velocity projectiles. Results are obtained using the ABAQUS final element code and compared against experimental results. The comparison indicates that currently available material properties models for honeycomb materials can be used to obtain a good approximation of the behavior of honeycomb sandwich structures under static and dynamic loading conditions.

• Proceedings of the KSR Conference
• /
• 2002.10a
• /
• pp.86-91
• /
• 2002

Glass/phenolic composite laminates have been used in the field of non-flammable light rail transit and their applications have expanded more widely. Low velocity impact tests have been used to evalute the effect of temperature and acceleration aging on low velocity impact response of phenolic matrix composites reinforced with woven E-glass fabric. The damage of matrix cracking and delamination are suddenly reduced the compressive strength after impact. The damage area increases with increasing temperature and impact energy. UT C-scan is used to determine damage areas by impact loading. Therefore, all this observations indicate reduced impact damage resistance and damage tolerance of the laminates at elevated temperature.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1585-1586
• /
• 2006

This paper conducts a study on the way the PCB's parallel plates' performances are affected by the loading of low cap. elements such as low cap-decoupling capacitors in conjunction with other lumped element. The fields and impedance profiles are rigorously evaluated and analyzed on various cases loaded with the above components and their effects will be given to bring better PCB EMC schemes.

• Journal of the Korean Institute of Navigation
• /
• v.4 no.1
• /
• pp.19-30
• /
• 1980

The usual procedure for the optimal design of ship's steering system is to minimize a chosen quadratic performance index, which isdetermined from the view point of economic run. However, the optimal control synthesized in such a straightforward fashion is unsatisfactory because ship's parameters differ from their nominal values due to uncertainties and errors in measurement and/or simplifications in mathematical modelling, and/or the variation of the ship's loading condition. In an attempt to resolve this difficulty, this paper presents a method for designing a low sensitive optimal steering system in a way as to minimize not only given performance index but also the sensitivity of the performance index and trajectory sensitivity. It is also shown that the optimal control so obtained will result in a system whose performance index and transient response are low sensitive to small varation in ship's time constant.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.1704-1705
• /
• 2007

A step-down procedure employing low voltage thermal transfer standard(LVTS) and micropotentiometer is described for the establishing the ac low voltage standards in the range of 2 mV to 200 mV below 1 MHz. Techniques are given for measuring input impedance with insertion method and calculating the loading error for the ac-dc transfer difference of the LVTS.

• Advances in materials Research
• /
• v.6 no.1
• /
• pp.65-78
• /
• 2017

A hat section was designed and developed for maximum impact energy absorption and/or transmission under low velocity impact. Towards this, different hat sections, having material properties of thermoplastic, were modeled and investigated numerically using finite element analysis (FEA) in the range of 20-50 J impact energy. In the study it was experienced that the design configuration of hat section with curvilinear profile (HSCP) was excellent in energy attenuation capacity and for even distribution of maximum impact force around and along the hat section under low velocity impact loading. To validate the numerical findings, polypropylene copolymer (Co-PP) HSCP and low density polyethylene (LDPE) HSCP were developed and evaluated experimentally in the said impact energy range. A correlation was established between FEA and experimental test results, thereby, validating a numerical model to predict results for other thermoplastic materials under given range of impact energy. The LDPE HSCP exhibited better performance as compared to Co-PP HSCP in the said range of impact energy. The findings of this study will enable the engineers and technologists to design and develop low velocity impact resistance devices for various applications including devices to protect bone joints.

• Korean Chemical Engineering Research
• /
• v.43 no.4
• /
• pp.452-457
• /
• 2005

Foam-type MFI zeolite catalyst was prepared by dispersing fine ($-0.2{\mu}m$) particles of MFI zeolite on silicalite foam. Catalytic cracking of n-octane was investigated over the foam-type catalyst and Delplot method was employed to interpret product compositions for deducing reaction mechanism. The Si/Al molar ratio of dispersed MFI zeolite was estimated 25 and its dispersed amount of silicalite foam was 25 wt％. Since the apparent density of the foam type catalyst was very low $0.11g{\cdot}cm^{-3}$, the catalyst loading amount could be varied from 0.02 g to 0.5 g without concerning pressure drop, providing a wide variance in the residence time of the reactants and products. The conversion and olefin yield in the catalytic cracking of n-octane increased with the catalyst loading. The product composition was very simple and could be explained by applying the protolytic cracking mechanism when the catalyst loading was small. Higher loading of the catalyst brought about further reactions of cracked products, accumulating lower olefin and paraffin with low reactivity in product stream and resulting in complex product composition.