• 한국산학기술학회논문지
• /
• 제20권11호
• /
• pp.494-500
• /
• 2019

본 연구는 탄약운반장갑차의 장약이송 소프트웨어 최적 설계를 통해 장약이송 시 파손을 방지하는 것을 목표로 하고 있다. 탄약운반장갑차는 자동화된 장약이송시스템이 적용되어 있다. 군 운용 중 장약 적재 시 간헐적으로 장약이 파손되는 현상이 발생하여 다음과 같은 개선방법을 연구하였고, 입증시험을 실시하였다. 장약 이송기의 속도가 높을 경우 충격력이 증가하기 때문에 적재 속도를 기존보다 60% 감소 시켰고, 포스 게이지를 활용하여 충격력을 측정하였다. 충격력 측정 결과 평균 45% 감소하는 것을 확인 할 수 있었다. 적재관 내부의 간섭 등에 의한 이송기의 부하 발생 시 서보제어기의 최대전류 11A를 출력하면 장약이 파손 될 가능성이 있다. 또한, 최대전류가 낮을 경우 장약적재가 불가하기 때문에 적정 값을 찾아야 했고, 이는 시험을 통하여 최적의 최대전류 값 6.5A를 도출하였다. 최적설계 입증 시험에는 종이지관장약과 실제장약을 적용하여 시험 하였다. 종이지관 장약과 실제 장약으로 탄운차에 장약 적재시험을 실시한 결과 장약의 파손이 발생하지 않았으며, 장약 적재가 정상적으로 이루어져 설계 개선이 타당한 것을 입증하였다.

• 복합신소재구조학회 논문집
• /
• 제6권2호
• /
• pp.105-117
• /
• 2015

The purpose of this study is to develop a new seismic resistant method by using precast concrete wall panels for existing low-rise, reinforced concrete beam-column buildings such as school buildings. Three quasi-static hysteresis loading tests were experimentally performed on one unreinforced beam-column specimen and two reinforced specimens with L-type precast wall panels. The results were analyzed to find that the specimen with anchored connection experienced shear failure, while the other specimen with steel plate connection principally manifested flexural failure. The ultimate strength of the specimens was determined to be the weaker of the shear strength of top connection and flexural strength at the critical section of precast panel. In this setup of L-type panel specimens, if a push loading is applied to the reinforced concrete column on one side and push the precast concrete panel, a pull loading from upper shear connection is to be applied to the other side of the top shear connection of precast panel. Since the composite flexural behavior of the two members govern the total behavior during the push loading process, the ultimate horizontal resistance of this specimen was not directly influenced by shear strength at the top connection of precast panel. However, the RC column and PC wall panel member mainly exhibited non-composite behavior during the pull loading process. The ultimate horizontal resistance was directly influenced by the shear strength of top connection because the pull loading from the beam applied directly to the upper shear connection. The analytical result for the internal shear resistance at the connection pursuant to the anchor shear design of ACI 318M-11 Appendix-D except for the equation to predict the concrete breakout failure strength at the concrete side, principally agreed with the experimental result based on the elastic analysis of Midas-Zen by using the largest loading from experiment.

• ETRI Journal
• /
• 제25권6호
• /
• pp.503-509
• /
• 2003

Selective epitaxial growth (SEG) of silicon has attracted considerable attention for its good electrical properties and advantages in building microstructures in high-density devices. However, SEG problems, such as an unclear process window, selectivity loss, and nonuniformity have often made application difficult. In our study, we derived processing diagrams for SEG from thermodynamics on gas-phase reactions so that we could predict the SEG process zone for low pressure chemical vapor deposition. In addition, with the help of both the concept of the effective supersaturation ratio and three kinds of E-beam patterns, we evaluated and controlled selectivity loss and non-uniformity in SEG, which is affected by the loading effect. To optimize the SEG process, we propose two practical methods: One deals with cleaning the wafer, and the other involves inserting dummy active patterns into the wide insulator to prevent the silicon from nucleating.

• 항공우주시스템공학회지
• /
• 제4권2호
• /
• pp.1-9
• /
• 2010

An airless tire has advantages over the conventional pneumatic tire in terms of flat proof and maintenance free. According to the recently disclosed inventions on the airless tire, non-pneumatic tire (NPT) consists of the flexible polygon spokes. Considering the NPT structure, the spokes undergo the tension-compression cyclic loading while the tire rolls. Therefore the spokes of NPT are required to have both stiffness and resilience under the cyclic tensile-compressible loading. In general, if a material has a high stiffness, it shows a low elastic strain limit. In this paper, using the auxetic honeycomb structure with negative poissons's ratio, the spokes of NPT tire are designed to have both stiffness and resilience. Finite element based numerical simulation of the contact pressure of a NPT is carried out with ABAQUS.

• 한국대기환경학회지
• /
• 제17권1호
• /
• pp.51-56
• /
• 2001

This study was carried out to interpret mathematically hydraulic behaviour in packing tower which packed 50 mm plastic Hiflow-ring with a dimension of 300 mm wide and 1,400 mm high. In view of energy saving, the recent packing. 50 mm plastic Higlow-ring was superior to conventional packings because of low pressure drop in high loads. As relative error between numerically predicted and experimentally obtained values was less then 6% in the loading and flooding point, it found that therir results appeared to be adequate. Comparison of hose two values in both dry and wet packing conditions. relative errors amount to 3.96 and 5.6%, respectively. In order to evaluate the operating characteristics of packing, the type, size, and material for packings must be estimated in various system and loads. This study is able to calculated pressure drop, hold-up, gas and liquid loads using mathematical interpretation. For these calculation, the specific constants of each packings must be calculated first all. The method of mathematical interpretation in this study turned out to be superior to the existing methods because of reduced errors at loading and flooding point.

• 한국초전도ㆍ저온공학회논문지
• /
• 제5권1호
• /
• pp.133-135
• /
• 2003

Cryogenic systems are requirement for the operation of HTS power cables. In general, HTS power cables require temperature below 77K, a temperature that can be achieved from the liquid nitrogen at latm or sub-cooled LN2 above latm. HTS power cable needs sufficient refrigeration to overcome its low temperature heat loading. This loading typically cones in two forms : (1) heat leaks from the surroundings and (2) internal heat generation. This paper explains the cooling test system of 10m HTS power cable. This system is composed of storage dewar, auto fill system, core cryostat and cold-box. Storage dewar is a LN2 storage tank and auto fill system is a LN2 supply device to the sub-cooler, Core cryostat is a LN2 flow line. Cold box is a control unit of temperature and flow rate. It is composed of control valve, flow meter, sub-cooler and circulation pump, etc..

• 한국재료학회지
• /
• 제13권11호
• /
• pp.732-736
• /
• 2003

A CP-GFRP(Carbon Powder-Glass Fiber Reinforced Plastic) sensor was fabricated for fracture detection. The electric resistance of the sensor was measured on condition of various composition of carbon powders and thickness of bundle of glass fibers. The resistance of the sensor was decreased as the increase of the content of carbon powders and the TEX of the glass fibers. In the case of loading on CP-GFRP, because inner crack was propagated, the part of percolation structures was disconnected. These observations show the following results. The conduction of CP-GFRP sensor is due to percolation structure of carbon powders and increase of resistance is due to expansion of cracks.

• 유체기계공업학회:학술대회논문집
• /
• 유체기계공업학회 1998년도 유체기계 연구개발 발표회 논문집
• /
• pp.91-96
• /
• 1998

The broadband noise generated aerodynamically from a two-bladed axial flow fan has been measured and compared to the result of a self-noise prediction method. The prediction scheme is based on the experimental data set acquired from a series of aerodynamic and acoustic tests of two and three-dimensional airfoil blade sections. For low blade loading case the comparison showed a reasonably good agreement, but as the loading becomes larger the empirical formula overpredict the sound pressure level at high frequency range. This is probably due to the use of stationary wing data for the prediction of rotating blade case, which will be quite different in their vortex strength at the blade tip.

• 환경위생공학
• /
• 제15권3호
• /
• pp.94-100
• /
• 2000

This study was carried out to interpret hydraulic behavior and CO2 gas desorption in counter-current packing tower which packed 50mm plastic Hiflow-ring. The results are as follow : To compare with conventional packing, 50mm Hiflow-ring could save energy because of low pressure drop under high load. As relative error between calculated value and investigated value was less than 6% in the loading point and flooding point we found that we are predict results mathematically which occur in packing tower. The unique magnitude of packing which was used are as follows. $C_L=2.1{\times}10^{-4}$, n=0.787 so we can predict efficiency which occur

• 한국생산제조학회지
• /
• 제9권4호
• /
• pp.34-47
• /
• 2000

Since carbon fiber epoxy composite materials have excellent properties for structures due to their high specific strength, high specific modulus, high damping and low thermal expansion, the hollow shafts made of carbon fiber epoxy composites have been widely used for power transmission shafts for motor vehicles , spindles of machine tools, motor base, bearing mount for tool up and manufacturing. The molded composite machine elements are not usually accurate enough for mechanical machine elements, which require turning drilling , cutting and grinding. The experiment are surface grinding wheel GC60 to the carbon fiber epoxy composite specimen with respect to staking angle [0]nT , [45]nT, [90]nT on the CNC grinding machine. In this paper, the surface grinding characteristics of composite plate, which are surveyed experimentally and analytically with respect to the grinding force, surface roughness and wheel loading according to the variable depth of cut, wheel velocity and table feed rate are investigated.