• Journal of Biosystems Engineering
• /
• 제37권2호
• /
• pp.100-105
• /
• 2012

Purpose: Methane production potential in aerobic digestion was assessed according to feed to inoculum (F/I) ratio for food waste only, and mixing ratio of two materials for food waste and swine manure to give a basic data for the design of anaerobic digestion system. Methods: Anaerbic digestion test was performed using a lab scale batch reactor at $35^{\circ}C$ for six different feed to inoculum (F/I) ratios (0.50, 0.72, 1.14, 1.50, 2.14 and 3.41), three food waste to swine manure ratios (100:0, 60:40 and 40:60) with two different loading concentrations (10g VS/L and 30g VS/L). Results: For food waste only, the highest biogas yield of 1008 mL/gVS was obtained at 0.50 of F/I. For the co-digestion of food waste and swine manure mixture, the highest biogas yield of 1148 mL/gVS was obtained at a mixing ratio of 40:60 with loading concentration of 10g VS/L. Conclusions: F/I ratio for the food waste only, mixing ratio of food waste and swine manure, and co-substrate loading rate affected the biogas production rate. For the low loading rate, there was not so much difference according to the mixing ratio of food waste and swine manure, but for the high loading rate higher biogas yield was acquired for the co-digestion of food waste and swine manure than for the food waste alone (mixing ratio, 100:0).

• Environmental Engineering Research
• /
• 제11권3호
• /
• pp.134-142
• /
• 2006

The treatment of high-strength swine wastewater by anaerobic digestion combined with an aquatic plant system was investigated. Anaerobic digestion of swine wastewater gave volatile solids (VS) removal efficiencies of 43.3%, 52.1% and 54.5% for hydraulic retention times (HRTs) of 20, 30, 40 days, respectively. The removal efficiencies of VS, total chemical oxygen demand (TCOD) and soluble chemical oxygen demand (SCOD) decreased with increasing VS volumetric loading rate (VLR). Higher organic removal efficiency was observed at longer HRTs for the same VS volumetric loading rate. As VS volumetric loading rate increased, biogas production increased and the methane content of the biogas decreased. Experiments using duckweed (Lemna species) as an aquatic macrophyte gave the following results. In the case of nitrogen, removal efficiency was above 60% and effluent concentration was below 10.0 mg/L when the influent ammonia-N loading was about $1.0\;g/m^2/day$. In the case of phosphorus, removal efficiency was above 55% and effluent concentration was below 2.0 mg/L when the influent $PO_4$-P loading was about $0.15\;g/m^2/day$. In addition, crude protein and phosphorus content of duckweed biomass increased from 15.6% to 41.6% and from 0.8% to 1.6%, respectively, as the influent nutrient concentration increased. The treatment of high-strength swine wastewater by anaerobic digestion combined with an aquatic plant system offers good performance in terms of organics and nutrient removal for relatively low operation and maintenance costs. The results indicate that under appropriate operational conditions, the effluent quality is within the limits set by Korean discharge criteria.

• 폴리머
• /
• 제32권5호
• /
• pp.421-426
• /
• 2008

pH감응형 P(MAA-co-EGMA) 수화젤을 분산 광중합을 이용하여 마이크로 크기의 미세입자로 합성하고 화장품 제형으로서의 응용 가능성을 평가하기 위하여 모델 탑재물질인 Rh-B와 화장품 분야에서 기능성 물질로 사용되는 ascorbic acid, adenosine, EGCG, arbutin을 이용하여 탑재 및 방출 거동을 조사하였다. Rh-B 탑재의 경우, pH 6.5인 수용액에서 이온화에 의한 P(MAA-co-EGMA) 수화젤의 음전하와 Rh-B의 양전하 사이의 정전기적 인력으로 인하여 가장 높은 탑재효율을 나타내었다. 그러나 화장품 기능성 물질들의 경우, pH 6.5 수용액에서 이온화된 P(MAA-co-EGMA) 수화젤의 음전하와 기능성 물질들이 나타내는 음전하 사이의 정전기적 반발력 때문에 상대적으로 낮은 탑재효율을 나타내었다. Rh-B를 사용한 방출실험 결과, p(MAA-co-EGMA) 수화젤 미세입자는 높은 pH에서는 다량의 Rh-B를 그리고 낮은 pH에서는 소량의 Rh-B를 방출하는 pH 감응성 방출거동을 나타내었다.

• 한국산업융합학회 논문집
• /
• 제27권1호
• /
• pp.229-237
• /
• 2024

The logistics industry is converging with digital technology and growing into various logistics automation systems. However, inspection and loading/unloading, which are mainly performed in logistics work, depend on human resources, and the workforce is shrinking due to the decline in the productive population due to the low birth rate and aging. Although much research is being conducted on the development of automated logistics systems to solve these problems, there is a lack of research and development on load stacking stability, which has the potential to cause significant accidents. In this study, loading boxes with various sizes and positions of the center of gravity were set up, and a method for stacking that with high stability is presented. The size of the loading box is measured using a depth camera. The loading box's weight and center of gravity are measured and estimated by a developed device with four loadcells. The measurement error is measured through various repeated experiments and is corrected using the least squares method. The robot arm performs load stacking by determining the target position so that the centers of gravity of the loading boxes with unbalanced masses with a random sequence are transported in alignment. All processes were automated, and the results were verified by experimentally confirming load stacking stability.

• 한국환경과학회지
• /
• 제16권4호
• /
• pp.449-458
• /
• 2007

Research results for the pressure drop variance depending on operation conditions such as change of inlet concentration, pulse interval, and face velocity, etc., in a pulse air jet-type bag filter show that while at $3kg/cm^2$ whose pulse pressure is low, it is good to make an pulse interval longer in order to form the first layer, it may not be applicable to industry because of a rapid increase in pressure. In addition, the change of inlet concentration contributes more to the increase of pressure drop than the pulse interval does. In order to reduce operation costs by minimizing filter drag of a filter bag at pulse pressure $5kg/cm^2$, the dust concentration should be minimized, and when the inlet dust loading is a lower concentration, the pulse interval in the operation should be less than 70 sec, but when inlet dust loading is a higher concentration, the pulse interval should be below 30 sec. In particular, in the case that inlet dust loading is a higher concentration, a high-pressure distribution is observed regardless of pulse pressure. This is because dust is accumulated continuously in the filter bag and makes it thicker as filtration time increases, and thus the pulse interval should be set to below 30 sec. If the equipment is operated at 1m/min of face velocity, while pressure drop is low, the bag filter becomes larger and thus, its economics are very low due to a large initial investment. Therefore, a face velocity of around 1.5 m/min is considered to be the optimal operation condition. At 1.5 m/min considered to be the most economical face velocity, if the pulse interval increases, since the amount of variation in filter drag is large, depending on the amount of inlet dust loading, the operation may be possible at a lower concentration when the pulse interval is 70 sec. However, for a higher concentration, either face velocity or pulse interval should be reduced.

• 콘크리트학회지
• /
• 제11권1호
• /
• pp.109-118
• /
• 1999

국내에서는 1988년부터 내진 규준이 시행되었으며, 따라서 그 이전에 지어진 저층 철근콘크리트 건물들은 내진 규준이 적용되지 않고 단지 축하중만을 고려하여 설계되었다. 그러므로 약한 지진이 발생하여도 이러한 건물들은 심한 피해를 입을 수 있다. 본 논문에서는, 내진 규준이 시행되기 이전에 지어진 비내진 저층 철근콘크리트 모멘트 저항 골조의 지진 발생시 거동과 피해를 알아보기 위하여, 실제 존재하는 비내진 건물 중 3층 철근콘크리트 라멘조 공공청사 건물의 외부 적합부를 교차보가 있는 것과 없는 것의 2종류를 1/2의 실물크기로 제작하고, 횡방향 변위 제어로 반복하중을 가하여 실험을 수행하였다. 비내진 접합부의 가장 큰 특징은 적합부내의 횡보강근이 없다는 것이다. 실험을 통하여 균열의 형태, 강도${\cdot}$강성의 저하, 에너지 소산 그리고 기둥과 보 부재의 철근 미끄러짐을 조사하였다. 국내에서 규정하고 있는 최대지반가속도인 0.12g크기의 횡방향 하중을 가력하였을 경우에는 균열이 발생하지 않았으나, 횡방향 하중을 0.12g이상으로 증가할수록 교차보가 없는 외부접합부에서 전단균열이 발생하였다.

• 한국산업보건학회지
• /
• 제5권1호
• /
• pp.104-118
• /
• 1995

This study was performed to evaluate factors affecting desorption of organic solvents collected on charcoal tube and to find out the optimum condition. Desorption efficiency for polar analytes was improved when several polar desorption solvents such as methanol, dimethylformamide(DMF), 2-(2-butoxyethoxy)ethanol were added to carbon disulfide($CS_2$). The best improvement was achieved when 10% dimethylformamide(DMF) in $CS_2$ was used as desorption solvent. During storage of polar analytes, recovery was greatly reduced. Especially, the recovery of cyclohexanone was decreased to 18.1 % after a month storage at $34^{\circ}C$. After two weeks storage, recovery of polar analytes was sharply decreased. Water adsorbed on charcoal interfered the recovery of polar analytes but didn't interfere that one of nonpolar solvent, toluene. When 10% DMF in $CS_2$ was used as desorption solvent, the effect of water on recovery was decreased, comparing with Desorption efficiency increased when analyte loading increased, and usage of 10% DMF in $CS_2$ decreased the loading effect. Increasing volume of desorption solvent was not effective to improve desorption efficiency of analytes when 10% DMF was used. Continuous shaking and sonication is not helpful to increase the desorption efficiency of analytes except cyclohexanone using 10% DMF. When silica gel used as adsorbent, methanol was better desorbent than dimethylsulfoxide. Analytes adsorbed on silica gel showed high recovery in low concentration and less affected by humidity. On the basis of this study, the following conclusions have been drawn. To improve the recovery of polar organic materials in air samples, it is necessary to analyze samples as soon as possible after they were collected. Otherwise, samples must be stored at low temperature. Using two components of desorption solvents, such as 10% DMF in $CS_2$, the effects of loading and humidity decreased for polar analytes such as methyl ethyl ketone and methyl isobutyl ketone. When work place has high humidity with low concentration of polar organic solvents, silica gel can be used as adsorbent, because it produces quantitative recovery for polar analytes at this condition. But it should be noted that high humidity makes breakthrough easy in silica gel samples.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 2005년도 춘계학술발표회
• /
• pp.465-466
• /
• 2005

(1) SA508 Gr.1a LAS exhibited a moderate cyclic hardening in $310^{\circ}C$ low DO water. A saturation stage or a slightly secondary hardening was occurred with decreasing strain amplitude. (2) Fatigue life of SA508 Gr.1a LAS decreases a little with decreasing strain rate in $310^{\circ}C$ low DO water.

• 자원환경지질
• /
• 제38권3호
• /
• pp.237-245
• /
• 2005

중금속으로 오염된 산성 지하수의 현장 정화방법으로 투수성반응벽체 기술의 적용 가능성을 평가하기 위하여 반응매질 선정을 위한 실내실험을 수행하였다. 처리대상 오염지하수로 이용한 임기광산 폐석적치장 침출수는 낮은 pH와 높은 금속농도를 갖는다(산도부하량으로 65 kg $CaCO_3$/일, 금속부하량(Fe+Al+Mn)으로 11.6kg/일). 이러한 특성의 오염지하수는 반응매질로 유기탄소 혼합물을 이용하여 황산염환원 반응에 의한 처리가 가능할 것으로 판단된다. 다섯 가지 서로 다른 배합비를 갖는 버섯퇴비, 소나무 바크, 석회석의 혼합 반응매질을 이용한 배치실험 결과를 통해 보면 투수성반응벽체를 적용할 경우 산도부하량은 12.3kg $CaCO_3$/일, 금속부하량은 3.3kg/일로 줄일 수 있다. 대상 지하수의 낮은 pH와 높은 금속부하량을 고려하여 무기탄소를 위주로 한 완충용 반응벽체를 먼저 두고, 이어서 유기탄소 혼합물로 구성되는 반응벽체로 황산염 환원을 유도하는 방법 적용한다면 보다 효과적인 광산배수에 대한 정화를 기대할 수 있을 것이다.

• Safety and Health at Work
• /
• 제6권2호
• /
• pp.120-127
• /
• 2015

Background: Musculoskeletal pain (MSP) is a common and disabling problem among carpet weavers and is linked to physical and psychosocial factors of work. This study aimed to determine the prevalence of MSP, its psychosocial risk factors, and association of pain in each pair of anatomical sites among carpet weavers. Methods: A cross-sectional study was performed among 546 hand-woven carpet weavers in rural small-scale workshops of Iran. Data were collected by using parts of a standardized CUPID (Cultural and Psychosocial Influences on Disability) questionnaire focused on MSP in 10 body sites, including the low-back, neck, both right and left shoulders, elbows, wrists/hands, individual, physical and psychosocial risk factors. Statistical analysis was performed applying logistic regression models. Results: Prevalence of MSP in at least one body sitewas 51.7% over the past month. The most common sites were low back and right shoulder pain 27.4% and 20.1%, respectively. A significant difference was found between the mean number of painful anatomical sites and the level of education, age, physical loading at work, time pressure, lack of support, and job dissatisfaction. In pairwise comparisons, strongest association was found between pain in each bilateral anatomical site (odds ratio = 11.6-35.3; p < 0.001). Conclusion: In home-based workshops of carpet weaving, psychosocial factors and physical loading were associated with MSP. This finding is consistent with studies conducted among other jobs. Considering the preventive programs, the same amount of attention should be paid to psychosocial risk factors and physical loading. Also, further longitudinal studies are needed to investigate the relationship of psychological factors.