• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.149-150
• /
• 2006

We describe a novel method of scanning probe nanofabrication using a AFM(atomic force microscopy) tip with assistance of Femtosecond laser pulses to enhance fabrication capability. Illumination of the AFM tip with ultra-short light pulses induces a strong electric field between the tip and the metal surface, which allows removing metal atoms from the surface by means of field evaporation. Quantum simulation reveals that the field evaporation is triggered even en air when the induced electric field reaches the level of a few volts per angstrom, which is low enough to avoid unwanted thermal damages on most metal surfaces. For experimental validation, a Ti: sapphire Femtosecond pulse laser with 10 fs pulse duration at 800 nm center wavelength was used with a tip coated with gold to fabricate nanostructures on a thin film gold surface. Experimental results demonstrate that fine structures with critical dimensions less than ${\sim}10nm$ can be successfully made with precise control of the repetition rate of Femtosecond laser pulses.

• 한국산업융합학회 논문집
• /
• 제25권6_3호
• /
• pp.1147-1154
• /
• 2022

Now that the development of autonomous driving is progressing, LiDAR has become an indispensable element. However, LiDAR is a device that uses lasers, and laser side effects may occur. One of them is the much-talked-about eye-safety, and developers have been satisfying this through laser characteristics and operation methods. But eye-safety is just one of the problems lasers pose. For example, irradiating a laser with a specific energy level or higher in a dusty environment can cause deterioration of the dust particles, leading to a sudden explosion. For this reason, the dust ignition proof regulations clearly state that "a source with a pulse period of less than 5 seconds is considered a continuous light source, and the average energy does not exceed 5 mJ/mm 2 or 35 mW" [2]. Energy of output optical power is limited by the law. In this way, the manufacturer cannot define the usage environment of the LiDAR, and the development of a LiDAR that can be used in such an environment can increase the ripple effect in terms of use in application fields using the LiDAR. In this paper, we develop a LiDAR with low optical power that can be used in environments where high power lasers can cause problems, evaluate its performance. Also, we discuss and present one of the directions for the development of LiDAR with laser power limited by dust ignition proof regulations.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.1958-1961
• /
• 2004

Ring Laser Gyroscopes used as navigational sensors inherently experience a lock-in region, where very low rotational rates are not measurable. Most RLG manufacturers use a mechanical dither motor that applies a small oscillatory rotational motion larger than this region to resolve this problem. Any input acceleration that bends this dithering axis causes flexure error, which is a noncommutative error that can not be compensated by simply using integrated gyro sensor output. This paper introduces noncommutative error equations that define attitude errors caused by flexure errors. In this paper, flexure error is classified as sensor level error if the sensing axis coincides with the dithering axis and as system level error if the two axes do not coincide. The relationship between gyro output and the rotation vector is introduced and is used to define the coordinate transformation matrix and angular motion. Equations are derived for both sensor level and system level flexure error analysis. These equations show that RLG based INS attitude error caused by flexure is directly proportional to time, amount of input acceleration and the dynamic frequency of the vehicle.

• Journal of Periodontal and Implant Science
• /
• 제38권4호
• /
• pp.657-668
• /
• 2008

Purpose: In this study, we compared low-power $CO_2$ laser treatment to ultrasonic scaling, which is generally approved as a power-driven mechanical instrumentation, and evaluated both of these treatments regarding their clinical effectiveness and change in the volume of in GCF. Material and methods: 20 patients who had gingivitis were selected. all of patients has no systemic problems. Randomly selected, one quadrant received ultrasonic scaling only, another quadrant received ultrasonic scaling and $CO_2$ laser irradiation, the other quadrant received $CO_2$ laser irradiation only. Clinical parameters measured at baseline, 1 weeks, 2weeks, 4weeks and 8weeks. Result: Pocket probing depth and clinical attachment level were not changed during study period. Gingival index of all group were improved after treatment. At 1 weeks after treatment, Gingival index of ultrasonic scaling group was only significantly different compared to control group. At 2 weeks after treatment, gingival index of all experimental group were significantly different compared to control group. At 4 and 8 weeks after treatment, gingival index of all group were increased, but experimental group were lower than control group. Sulcus bleeding index was similar to the results of gingival index. At 1 weeks after treatment, all experimental group were significantly different compared to control group and it maintained during study. At 2 weeks after treatment, sulcus bleeding index of all group were lowest during study. Gingival crevicular fluid were measured with $Periotron^{(R)}$ 8000($Oraflow^{(R)}$, Inc. USA). At baseline, all group were showed moderately severe condition. At 1 week after treatment, laser treatment only group was reduced quantity of gingival crevicular fluid mostly, and all group were reduced quantity of gingival crevicular fluid. At 2 weeks after treatment, all group were health state. At 4 and 8 weeks after treatment, all group were showed recurrent of inflammation, and control group was the most significantly increased. Conclusion: This study showed that the effects of $CO_2$ laser treatment were similar to conventional ultrasonic scaling and this result remained longer than plaque control only. These results suggest possibility of $CO_2$ laser treatment for altered periodontal therapy.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2004년도 춘계학술대회 논문집
• /
• pp.365-372
• /
• 2004

1)고강도강 BOP 시험 결과 강종에 차이 없이 용접속도에 따라 유사한 비드 형상을 가지는 것으로 나타났다. 한편 1.2t 시험편의 적정 용접속도는 $4\~8m/min$으로 나타났다. 2) 용접속도가 빠를수록 비드폭은 작아지며, 경도값은 높게 나타났다. 그리고, 최고 경도값은 강의 성분(Ceq)에 비례하는 것으로 나타났음, 그 결과 TRIP80(Ceq=0.53)의 경우 최고 520Hv이상의 경도값을 가지고 있었다. 3) LDH test 결과 DP강의 모재대비 용접부의 성형성이 약 $90\%$ 정도로 나타났으며, TRIP 및 일반 고강도강은 약 $80\%$의 성형성을 갖는 것으로 확인되었다. 4) He을 보호가스로 사용시 기공의 형성은 크게 억제되었다. 그리고 Ar 사용시에는 기공 형성이 He에 비해 많이 형성되는 것으로 나타나 사용시 주의가 필요한 것으로 보인다. 기공 형성은 TRIP > 60C/45R > DP 순서로 나타나 DP강이 가장 좋은 레이저 용접성을 가지고 있었다.

• The Korean Journal of Pain
• /
• 제14권1호
• /
• pp.51-55
• /
• 2001

Background: Oral mucositis is a common complication of anticancer chemotherapy. The sequelae of this consist of an increased risk of infection, moderate to severe pain, compromised oral function, and bleeding. This study was performed to evaluated the effects of the He-Ne laser and the Ga-Al-As laser on oral mucositis caused by anticancer chemotherapy in pediatric patients. Methods: There were 3 cases of osteosarcoma and 6 cases of leukemia. All patients received He-Ne laser (632.8 nm wavelength, power 60 mW) application on 400-600 Hz scanning for 5-20 minutes and Ga-Al-As laser (904 nm wavelength, power 40 mW) application by fiberoptic hand piece placed in immediate proximity to the tissue without direct contact with it for 30 seconds per point for 5 days per week. During the application patients wore wavelength-specific dark glasses and were instructed to keep their eyes closed. Results: The mean number of treatments with oral intake was $4.89{\pm}0.64$. The mean number of total treatments was $9.44{\pm}2.59$. There were no significant side effects during and after the laser treatments. Conclusions: He-Ne laser and Ga-Al-As (IR) laser treatment were well tolerated and reduced the severity and duration of chemotherapy-induced oral mucositis in pediatric oncologic patients.

• The Journal of Korean Physical Therapy
• /
• 제14권2호
• /
• pp.234-249
• /
• 2002

This study was performed, using c-fos and Substance P, to investigate the effect of GaAlAs laser on acute pain model induced by wound in lumbar region's spinal level. The test group was divided into control and experimental group. Control group is shamed group(c-fos and substance P expression after non-irradiation by a GaAlAs laser), The experimental group was divided into two subgroups: one is experimental group I (c-fos expression after irradiation by a GaAlAs laser), and the other is experimental group II (substance P expression after irradiation by a GaAlAs laser). The results of this study were as following: 1. The numbers of c-fos immunoreactive neuron in spinal cord was increased markedly 1 day after wound, and decreased gradually from 1 day to 2 days in wound with GaAlAs laser irradiation. 2. The changes of the average percentages of substance P immunoreactive neurons in spinal cord was increased markedly 1 day after wound, and decreased gradually from 1 day to 2 days in wound with GaAlAs laser irradiation. Therefore, decreasing the changes of c-fos and substance P expression after irradiation by a GaAlAs laser indicates and GaAlAs laser have effect on pain control.

• The Korean Journal of Pain
• /
• 제3권2호
• /
• pp.139-143
• /
• 1990

대상포진성 신경통 환자의 통증을 조정하기 위한 목적으로 본원 통증치료실을 내원한 환자 26명을 대상으로 저출력 레이저 치료를 시행한 결과는 아래와 같다. 1) 통증완화 효과에 대한 평가로서 LLLT는 통증환자에게 비침습적이고 안전하게 시행할 수 있었다. 2) 저출력 레이저 조사후 VAS의 변화는 치료전 $7.57{\pm}1.81$, 5회후 $4.01{\pm}2.01$ 10회후 $3.28{\pm}1.85$ 15회후 $2.82{\pm}1.95$이었다(p<0.01). 3) 15회의 LLLT후 VAS의 개선율은 63%였다. 4) 가장 현저한 VAS의 개선율은 1회 LLLT후의 24%였고 VAS의 개선율은 7회 LLLT후에 나타났다. 5) 대상포진후 신경통으로의 이환은 60세 이상군에서 나타난 1명(3.8%)이었다. 60세 이하 군에서 VAS의 변화는 치료전 $7.67{\pm}2.31$, 5회후 $3.42{\pm}1.77$, 10회후 $2.88{\pm}1.33$, 15회후 $2.22{\pm}1.63$이었으며 VAS의 개선율은 각각 55%, 62%, 71%였다. 60세 이상 군에서는 VAS의 변화는 치료전 $7.49{\pm}1.44$, 5회후 $4.51{\pm}2.20$, 10회후 $3.76{\pm}2.38$, 15회후 $3.47{\pm}2.32$이고 VAS의 개선율은 각각 40%, 50%, 54%로 유의한 차이가 없었다(p>0.05). 7) LLLT중이나 후에 특이한 합병증은 없었다. 이상에서 볼 때 대상포진성 신경통 환자에서 LLLT는 초기에 통증을 조절할 뿐만 아니라 대상포진후 신경통으로의 이환을 줄이며 환자의 전신상태와 비교적 무관하게 치료를 적용할 수 있는 방법으로 사료된다.

• 대한치과기공학회지
• /
• 제36권4호
• /
• pp.239-246
• /
• 2014

Purpose: The purpose of this study was to compare the tensile strength and mechanical properties of orthodontic wire joints made by gas soldering and laser welding, with and without filling material, to identify the effectiveness and potential clinical application of laser welded orthodontic wires. Methods: Three joint configurations of orthodontic wire were used: diameter 0.9 to 0.9 mm wire, diameter 0.9 to 0.5 wire and diameter 0.9 mm wire to band. The joints were made using three different methods: gas soldering, laser welding with and without filling material. For each kind of joint configuration or connecting method 7 specimens were carefully produced. The tensile strengths were measured with a universal testing machine (Zwick/Roell, Instron, USA). The hardness measurements were carried out with a hardness tester(Future-Tech Co. Tokyo, Japan). Data were analyzed by AVOVA(p= .05) and Turkey HD test(p= .05). Results: In all cases, gas soldering joints were ruptured on a low level on tensile bonding strength. Significant differences between laser welding and gas soldering(p< .05) were found in each joint configuration. The highest tensile strength means were observed for laser welding, with filling material, of 0.9 to 0.9 mm wire joint. Conclusion: In conclusion, the elastic modulus and tensile strength means of laser soldering with filling material were the highest, and the tensile strength means of laser soldering were higher than those of gas soldering.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2009년도 제38회 동계학술대회 초록집
• /
• pp.322-322
• /
• 2010

For boron doping on n-type silicon wafer, around $1,000^{\circ}C$ doping temperature is required, because of the relatively low solubility of boron in a crystalline silicon comparing to the phosphorus case. Boron doping by fiber laser annealing and lamp furnace heat treatment were carried out for the uniformly deposited p-a-Si:H layer. Since the uniformly deposited p-a-Si:H layer by cluster is highly needed to be doped with high temperature heat treatment. Amorphous silicon layer absorption range for fiber laser did not match well to be directly annealed. To improve the annealing effect, we introduce additional lamp furnace heat treatment. For p-a-Si:H layer with the ratio of $SiH_4:B_2H_6:H_2$=30:30:120, at $200^{\circ}C$, 50 W power, 0.2 Torr for 30 min. $20\;mm\;{\times}\;20\;mm$ size fiber laser cut wafers were activated by Q-switched fiber laser (1,064 nm) with different sets of power levels and periods, and for the lamp furnace annealing, $980^{\circ}C$ for 30 min heat treatment were implemented. To make the sheet resistance expectable and uniform as important processes for the $p^+$ layer on a polished n-type silicon wafer of (100) plane, the Q-switched fiber laser used. In consequence of comparing the results of lifetime measurement and sheet resistance relation, the fiber laser treatment showed the trade-offs between the lifetime and the sheet resistance as $100\;{\omega}/sq.$ and $11.8\;{\mu}s$ vs. $17\;{\omega}/sq.$ and $8.2\;{\mu}s$. Diode level device was made to confirm the electrical properties of these experimental results by measuring C-V(-F), I-V(-T) characteristics. Uniform and expectable boron heavy doped layers by fiber laser and lamp furnace are not only basic and essential conditions for the n-type crystalline silicon solar cell fabrication processes, but also the controllable doping concentration and depth can be established according to the deposition conditions of layers.