• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제5B권4호
• /
• pp.358-365
• /
• 2005

In induction machine drive without a speed sensor, the estimation of the motor flux and speed often becomes deteriorated at low speeds with low back EMF. Our analysis shows that, in addition to the state resistance variation, the estimated value of field orientation angle is often corrupted by accumulative errors from the integration of voltage variables at motor terminals that have low signal/noise ratio at low frequencies. A repetitive loop path of integration in the feedback can amplify this type of error, thus speeding up the degradation process. The control system runs into information starvation due to the loss of correct field orientation. The machine's spiral vectors are controlled only in a reduced dimension in this situation. A novel control scheme is developed to improve the control performance of motor's current, torque and speed at low frequencies. The scheme gains a full-dimensional vector control and is less sensitive to the combined effect of the error sources at the low frequencies. Experimental tests demonstrate promising performances are achievable even below 0.5 Hz.

• Journal of Mechanical Science and Technology
• /
• 제17권4호
• /
• pp.511-520
• /
• 2003

In room acoustics, reverberation time is an important acoustic parameter. However it is often difficult to measure short reverberation times at low frequencies with a traditional band pass filter bank if the product of filter bandwidth (B) and reverberation time (T) is small. It it well known that the minimum permissible product of bandwidth and reverberation time of the traditional band pass filter is at least 16. This strict requirement makes it difficult to measure short reverberation times of an acoustic room at low frequencies exactly. In order to reduce this strict requirement, in the previous paper, the wavelet filter bank was developed and the minimum permissible product of bandwidth and reverberation time was replaced with 4. In the present paper it is demonstrated how the short reverberation times of an practical room at low frequencies are successfully measured by using the wavelet filter bank and the results are compared with the traditional method using a band past filer bank.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.1077-1080
• /
• 2002

In building acoustics, reverberation time is an important acoustic parameter. However, it is often difficult to measure short reverberation times at low frequencies using the traditional band pass filter bank if the product of bandwidth (B) and reverberation time (T) is small. It is well known that the minimum permissible product of bandwidth and reverberation time of the traditional band pass filter is at least 16 ［F. Jacobsen, J. Sound Vib. 115, 163-170 (1987)]. This strict requirement makes it difficult to measure short reverberation times of an acoustic room at low frequencies exactly. In order to reduce this strict requirement, recently, the wavelet filter bank is developed and the minimum permissible product of bandwidth and reverberation time is replaced with 4 [S. K. Lee, J, Sound Vib. 252, 141-153 (2002)]. In the present paper, it is demonstrated how the short reverberation times at low frequencies are successfully measured by using the wavelet filter bank. In order to present this job, two synthetic signals and one measured signal are used for impulse responses of an acoustic room.

• 한국소음진동공학회논문집
• /
• 제14권1호
• /
• pp.50-55
• /
• 2004

In this study, slit-tones by plane impinging jet are investigated experimentally over the whole subsonic flow range, especially at low speeds, in order to obtain the instability behaviour of impinging plane jet. Slit-tones are generated at low speeds associated with laminar shear layer instability as well as at high speeds associated with turbulent instability. Most of low-speed slit-tones are induced by symmetric mode instability unless the slit is not so wide, in which case antisymmetric modes are induced like edge-tones. It is found that the frequencies at low speeds ate controled by the unstable condition of the vortex at the nozzle exit and its pairings by which the frequencies are decreased by half. In the case of symmetric modes related with low-speed slit-tones, frequencies lower than those associated with one-step pairings are not found.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2012년도 추계학술대회 논문집
• /
• pp.388-393
• /
• 2012

Vibration condition monitoring at low rotational speeds is still a challenge. Acoustic emission (AE) is the most used technique when dealing with low speed bearings. At low rotational speeds, the energy induced from surface contact between raceway and rolling elements is very weak and sometimes buried by interference frequencies. This kind of issue is difficult to solve using vibration monitoring. Therefore some researchers utilize artificial damage on inner race or outer race to simplify the case. This paper presents vibration signal analysis of low speed slewing bearings running at a low rotational speed of 15 rpm. The natural damage data from industrial practice is used. The fault frequencies of bearings are difficult to identify using a power spectrum. Therefore the relatively improved method of empirical mode decomposition (EMD), ensemble EMD (EEMD) is employed. The result is can detect the fault frequencies when the FFT fail to do it.

• 대한조선학회지
• /
• 제17권3호
• /
• pp.1-4
• /
• 1980

It is well known that discrepancies between measured and predicted ship motions are significant in the range of low frequencies. In this paper, the vertical ship motions in regular longitudinal waves in a shallow water are briefly discussed. The investigation is focussed on the role of wave exciting forces and moments to the motion responses in these low frequencies. It is confirmed that diffraction forces are in general small in a shallow water as one may expect. Furthermore the wave exciting forces and moments on a displacement-type ship will be larger practicularly in low frequencies, when the contribution of the diffraction effect is neglected. As a result of this fact theoretically predicted responses for the pitch motion becomes closer to the experimental one. The discrepancies for the heave motion, however, are still apparent.

• 동력기계공학회지
• /
• 제17권1호
• /
• pp.36-41
• /
• 2013

A study of the possible axisymmetric modes that propagate at low frequencies in buried, water-filled pipes is presented. It is well known that for a vacuum-pipe-vacuum system the sole non-torsional axisymmetric mode that exists at low frequencies is the fundamental L(0,1) mode. When a pipe is filled with water and still surrounded by a vacuum it is also known that another mode then appears which at low frequencies is characterized by predominantly axial water-borne displacements. In addition to these modes. this paper explores two other, less well known axisymmetric modes whose exitence depends on the acoustic properties of the outer medium that surrounds a pipe. The predicted characteristics of these modes are presented and the likelihood of them propagating over any significant distance in a buried water pipe is discussed.

• 동력기계공학회지
• /
• 제10권1호
• /
• pp.65-70
• /
• 2006

A study of the possible axisymmetric modes that propagate at low frequencies in buried, water-filled iron pipes is presented. It is well known that for a vacuum-pipe-vacuum system the sole non-torsional axisymmetric mode that exists at low frequencies is the fundamental L(0,1) mode. When a pipe is filled with water and still surrounded by a vacuum it is also known that another mode then appears which at low frequencies is characterized by predominantly axial water-borne displacements. In addition to these modes, this paper explores two other, less well known axisymmetric modes whose existence depends on the acoustic properties of the outer medium that surrounds a pipe. In this paper the predicted characteristics of these modes are presented.

• 대한전자공학회논문지SP
• /
• 제42권4호
• /
• pp.111-118
• /
• 2005

본 논문에서는 진폭 변조 기법을 이용하여 빔포머의 저주파 대역 특성을 개선함으로써 전체적인 잡음 제거 성능을 향상하고자 한다. 일차원 등간격 선형 마이크로폰 어레이를 사용하여 잡음 제거를 할 때, 협대역의 잡음 신호에 대해서는 delay-and-sum 빔포밍으로도 적절한 빔폭을 갖는 빔패턴이 형성되므로 효과적으로 잡음을 제거할 수 있다. 그러나 광대역 잡음 신호에서는 aliasing을 피하기 위해 고주파 신호에 맞게 마이크로폰들을 등간격으로 조정하면 저주파로 갈수록 빔폭이 털어져서 저주파 대역의 잡음은 잘 제거되지 않는다. 광대역 신호에 대해 일정한 빔폭을 갖게 하는 방법들로서 서브 어레이들을 이용한 빔포밍[1][2][3][4] 이나 멀티 빔포밍[5] 등이 제안되어 왔다. 하지만, 이러한 방법들은 주파수에 따라 마이크로폰 간격을다르게 해야 한다는 원리를 기반으로 하는 것이므로 저주파 대역에서도 고주파 대역에서와 같은 좁은 빔폭을 얻기 위해서는 어레이의 크기가 커져야 하는 단점이 있다. 제안하는 알고리즘은 통신에서 주로 사용하는 진폭 변조 기법을 빔포밍에 이용한 것으로서 저주파 대역 신호를 고주파 대역으로 옮김으로써 작은 크기의 마이크로폰 어레이에서도 저주파 대역 잡음을 줄일 수 있는 장점이 있다. 등간격 선형 마이크로폰 어레이에 제안된 방법을 적용한 실험 결과에서 기존의 방법들에 비해 잡음의 저주파 성분이 잘 제거됨을 알 수 있다.

• 전기전자학회논문지
• /
• 제26권4호
• /
• pp.693-704
• /
• 2022

5G 서비스는 기존 이동통신주파수보다 상대적으로 높은 중대역(n78)을 사용하고 있어서 2GHz 이하의 저대역 주파수를 활용하여 5G 커버리지 개선이 필요하다. 이를 위해서는 저대역 주파수의 대부분을 사용하는 LTE와 5G-NR 시스템의 동적 스펙트럼 공유(Dynamic Spectrum Sharing) 기술의 적용이 요구된다. 본 논문에서는 DSS 적용을 위한 시그널링 오버헤드 요소와 단말기 구현 RF 이슈들을 도출하고, 저대역 주파수 중 광대역 주파수 활용이 가능한 1.8GHz 대역(50MHz 폭)에 대해 5G-NR과 LTE 각각의 관점에서 시그널링 오버헤드 비율과 단말기 RF 이슈들을 분석하였다. 분석 결과들을 통해 저대역을 활용한 DSS 기술을 적용한다면 LTE 트래픽이 5G-NR로 빠르게 이전할 경우, 5G 커버리지 개선으로 인해 우수한 서비스 품질을 제공할 수 있을 것으로 예상된다.