• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 하계학술대회 논문집 B
• /
• pp.898-900
• /
• 2001

In general, the accuracy of the switching angles is dependent upon the resolution of the encoder and the sampling period of the microprocessor. But the region of high speed, switching angles are fluctuated back and forth from the preset values, which are cause by the sampling period of the microprocessor. Therefore, the low cost linear encoder suitable for the practical and stable SRM drive is proposed and the control algorithm to provide the switching signals using the simple analog type switching logic circuit is also presented in this paper.

• 한국소음진동공학회논문집
• /
• 제14권6호
• /
• pp.455-462
• /
• 2004

This paper is concerned with the implementation of the active vibration suppression controller using analog circuit and microprocessor. The target active vibration controller is the positive position feedback(PPF) controller since it provides a simple algorithm suitable for both analog circuit and digital controllers. In this study, the analog PPF controller is realized using an operational amplifier and the digital PPF controller is realized using a low-cost micro-controller. The circuit diagrams are explained in detail. We then discuss the advantages and disadvantages of both methods from the view of practical implementation. Experimental results show that both implementation methods can be effectively used for the active vibration control but need to be chosen based on the mission objective.

• 한국자동차공학회논문집
• /
• 제7권5호
• /
• pp.9-15
• /
• 1999

A digital CDI(Capacitive Discharge Ignition) system on small two stroke motorcycle engine was developed in this paper, This CDI system with microprocessor as its main part has more flexible spark timing than the conventional CDI system because of its programmable characteristics. The principle of this digital CDI system and the design methods of hardware and software were presented in this paper, Two stroke small engine was tested to investigate the performance of digital CDI system And also this system was investigated to optimize the engine performance. Also comparison between conventional CDI can provide better spark timing variation than the conventional system. The part and full load test results show that the engine power was increased about 10-20% and fuel consumption was decreased about 10-20% simultaneously. Furthermore, this digital CDI system has simple structure, low cost and very little modification are required. It is a promising technology to substitute for the widely used conventional CDI system.

• 대한전자공학회논문지
• /
• 제16권2호
• /
• pp.1-6
• /
• 1979

본 논문에서는 computer제어에 의한 한글문 편집 system의 개발에 관해 논한다. 한글의 24기본자수로서 문자를 합성하고, 영숫자를 혼용한 문장의 editing이 간단히되는 편집 system을 minicomputer에 실현시켜, 한글 입출력용 terminal의 지능화의 가능성을 밝힌다. 나아가서, microprocessor와 CRT-display를 이용하여 값싸고 고기능을 발휘하는 system, HIT(Hanguel-Intelligent-Terninal)의 구성예를 보인다.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• 제11B권4호
• /
• pp.185-192
• /
• 2001

In SRM drive, the ON·OFF angles of each phase switch should be accurately controlled in order to control the torque and speed stably. The accuracy of the switching angles is dependent upon the resolution of the encoder and the sampling period of the microprocessor, that are used to provide the information of the rotor position and to control the SRM power circuit, respectively. However, as the speed increases, the amount of the switching angle deviation from the preset values is also increased. Therefore, the low cost encoder suitable for the practical and stable SRM drive is proposed and the control algorithm to provide the switching signals using the simple digital logic circuit is also presented in this paper, As a result, a stable high speed SRM drive can be achieved by the high resolution switching angle control and it is verified from the experiments that the proposed encoder the logic controller can be a powerful candidate for the practical low cost SRM drive.

• International Journal of Ocean System Engineering
• /
• 제2권4호
• /
• pp.223-232
• /
• 2012

For the accurate estimation of the position and orientation of a UUV (unmanned underwater vehicle), a low-cost AHRS (attitude heading reference system) was developed using a low-cost IMU (inertial measurement unit) sensor which provides information on the 3D acceleration, 3D turning rate and 3D earth-magnetic field data in the object coordinate system. The main hardware system is composed of an IMU sensor (ADIS16405) and TMS320F28335, which is coded with an extended kalman filter algorithm with a 50-Hz sampling frequency. Through an experimental gimbal device, good estimation performance for the pitch, roll, and yaw angles of the developed AHRS was verified by comparing to those of a commercial AHRS called the MTi system. The experimental results are here presented and analyzed.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(1)
• /
• pp.210-213
• /
• 2004

In a switched reluctance motor drive, it is important to synchronize the stator phase excitation with the rotor position, because the position of rotor is an essential information. In the high-speed region, switching angles are fluctuated back and forth out of the preset value, which is caused by the sampling period of the microprocessor. In this paper, a low cost analog encoder to be suitable for practical applications is proposed. The validity of the proposed analog encoder with a proper logic controller is verified from the experiments.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 춘계학술대회논문집 - 한국공작기계학회
• /
• pp.159-164
• /
• 2000

In SRM drive, The accuracy of the switching angles is dependent upon the resolution of the encoder and the sampling period of the microprocessor. As the speed increased, the amount of the switching angle deviation from the preset values is increased by the sampling period. Therefore, in this paper the low cost liner encoder for the practical and stable SRM drive is proposed and the control algorithm to provide the switching signals using the simple digital logic circuit is presented. and it is verified from the experiments that the proposed encoder and logic controller can be a powerful candidate for the practical low cost SRM drive.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2000년도 제15차 학술회의논문집
• /
• pp.33-33
• /
• 2000

In this paper a new distributive control system for BA(Building Automation ) lighting control used on general microprocessors is presented. For optimal lighting control and saving energy, The system have to control the group and pattern lighting control as well as individual light control at one time. Tn this paper, This functions are accomplished with low-cost and simple microprocessor. A plurality of modulated light control terminals are connected to the central control unit through a pair of power line. This power line provide both power and signal to the each terminal and the data is transmitted through cyclic time division multiplex transmission. With this structure a low-cost distributive control system for lighting applications has been achieved, allowing energy and maintenance saving and reliability increase of the light control system.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.372-376
• /
• 2001

Due to several advantages of Pulse Width Modulation(PWM) Converter, such as unity power factor operation, elimination of low-order harmonics and regeneration of motor braking energy to source, the application range of PWM Converter has been rapidly extended in industrial application. Nowadays, vector control algorithm and space vector PWM(SVPWM) method are applied to improve the performances of PWM Converter, but vector control algorithm and SVPWM require to use Microprocessor and other digital devices in hardware, causing costly and somewhat large dimension system. In every practical application of energy conversion equipments, the design and implementation should be carried out considering cost and performance. High performance and low cost is the best choice for energy conversion equipments. So, this paper presents the practical design method and implementation results of 3-phase PWM Converter with analog hysteresis current controller, and verifies the performances of unit power factor operation and energy regeneration operation via experimental results.