• 한국멀티미디어학회논문지
• /
• 제16권9호
• /
• pp.1067-1076
• /
• 2013

Known as an important criterion that evaluates performance of future high-speed backbone networks, burst data loss ratio is well-studied in Optical Burst Switching networks. Current literatures mostly focus on reduce burst loss ratio without considering the system stability and link utilization after reducing. In this paper, we propose a novel framework which comes from feedback theoretic to dynamically control burst loss ratio in OBS. The proposed scheme tries to track the pre-set values of burst loss ratio and increases the stability and link utilization degree. The simulation results show that measured burst loss ratio always tracks setup reference with small errors, wavelength channel utilization is increased up to 2% and the system stability is also improved.

• International Journal of Industrial Entomology and Biomaterials
• /
• 제26권1호
• /
• pp.13-21
• /
• 2013

Boil-off loss ratio is one of the most important economic traits to be considered during the course of silkworm breeding. The boil-off loss ratio varies among the breeds and seasons. The present study was undertaken with 5 oval and 5 peanut breeds and twenty five hybrids involving these parents to select the promising hybrids with desired boil-off loss ratio. Accordingly, studies were undertaken to estimate the heterosis and heterobeltiosis. It was observed that majority of the hybrids revealed negative heterosis for boil-off loss ratio which is desirable. Based on the heterosis and heterobeltiosis, among all the hybrids, the hybrid APBRO5 ${\times}$ APBRD5 exhibited highest negative heterosis for boil-off loss ratio and also exhibited highest EI value (64.5) for the quantitative and qualitative traits. Based on the hybrids performance, boil-off loss ratio, heterosis and heterobeltiosis and evaluation index, the hybrids viz. APBRO5 ${\times}$ APBRD5, APBRO1 ${\times}$ APBRD1 and APBRO3 ${\times}$ APBRD4 were identified for commercial exploitation.

• 응용통계연구
• /
• 제25권1호
• /
• pp.101-114
• /
• 2012

자동차보험의 손해율이란 지급보험금의 수입보험료에 대한 비율을 의미한다. 손해율이 매우 큰 값을 갖는 대형손실이 일어나는 경우에는 보험회사의 재무적인 부분에 큰 악영향을 미치게 된다. 따라서 보험회사가 이에 대비할 수 있도록 하기 위하여 손해율의 극단 분위수(extreme quantile)를 추정하는 것은 매우 중요한 일이다. 다른 종류의 보험 관련 데이터와 같이 손해율의 분포는 오른쪽으로 긴 꼬리를 갖는 두꺼운 꼬리분포(heavy-tailed distribution)를 갖는다. 이런 자료에서 극단 분위수룰 추정하기 위하여 가장 많이 사용되는 방법론은 POT(Peaks over threshold)와 Hill 추정(Hill estimation)이다. 본 논문에서는 일반화파레토분포(generalized Pareto distribution; GPD)의 다양한 모수추정방법론의 성능을 모의실험과 실제 손해율 데이터를 사용하여 비교, 분석하였다. 또한 Hill 추정치를 사용하여 극단 분위수를 추정하였다. 그 결과 대부분의 경우에 POT 방법론이 Hill 추정치를 이용한 방법보다 정확한 분위수를 추정하였고, 모수추정방법론 중에서는 MLE, Zhang, NLS-2 방법론이 가장 좋은 결과를 보여주었다.

• Journal of Periodontal and Implant Science
• /
• 제42권6호
• /
• pp.231-236
• /
• 2012

Purpose: The aim of this study was to evaluate the influence of the crown-to-implant (C/I) ratio on the change in marginal bone level around the implant and to determine the site-related factors influencing the relationship between the C/I ratio and periimplant marginal bone loss. Methods: A total of 259 implants from 175 patients were evaluated at a mean follow-up of five years. Implants were divided into two groups according to their C/I ratios: ${\leq}$ 1, and >1. Site-related factors having an influence on the relationship between C/I ratio and periimplant marginal bone loss were analyzed according to the implant location, implant diameter, implant manufacturer, prosthesis type, and guided bone regeneration (GBR) procedure. Results: It was found that 1) implants with a C/I ratio below 1 exhibited greater periimplant marginal bone loss than implants with a C/I ratio more than 1, 2) site-related factors had an effect on periimplant marginal bone loss, except for the implant system used, 3) the C/I ratio was the factor having more dominant influence on periimplant marginal bone loss, compared with implant diameter, prosthesis type, implant location, and GBR procedure, 4) implants with a C/I ratio below 1 showed greater periimplant marginal bone loss than implants with a C/I ratio greater than 1 in the maxilla, but not in the mandible, 5) and periimplant marginal bone loss was more affected by the implant system than the C/I ratio. Conclusions: Within the limitations of this study, implants with a higher C/I ratio exhibited less marginal bone loss than implants with a lower C/I ratio in the posterior regions. The C/I ratio was a more dominant factor affecting periimplant marginal bone loss in the maxilla than the mandible. Meanwhile, the implant system was a more dominant factor influencing periimplant marginal bone loss than the C/I ratio.

• 한국농공학회논문집
• /
• 제57권1호
• /
• pp.11-23
• /
• 2015

In this study the laboratory test for hydraulic conductivity and the seepage analysis with finite element method on measurement section of sea dike embankment were performed for the purpose of estimating the relative density of embankment from the measured pore water pressures, and both results of the test and the analysis were coupled with the method of estimating seepage blocking state with the hydraulic head loss rate in sea dike embankment. The relationship of void ratio vs hydraulic head loss rate was obtained by setting hydraulic conductivity as common ordinate on the relationships between the void ratio and the hydraulic conductivity and between the hydraulic conductivity and the hydraulic head loss rate. The void ratio on the segment between measuring points was calculated from the coupled relationship of the void ratio vs the hydraulic conductivity. The allowable upper and lower limits of hydraulic head loss rate and those of void ratio on the safety were generated from the coupled relationship between the laboratory compaction test and the sedimentation test. Current hydraulic head loss rate and void ratio were evaluated in the allowable range between upper and lower limits.

• 한국자동차공학회논문집
• /
• 제14권4호
• /
• pp.157-163
• /
• 2006

A modified ratio control algorithm is proposed for the improvement of the fuel economy for a metal belt CVT. In the modified ratio control algorithm, the CVT ratio is controlled to operate the engine on the optimal operation region which provides the best efficiency from the view point of the overall efficiency of the engine-CVT system. In order to construct the modified ratio map, the CVT system loss model is used by assuming that the all the loss is attributed to the torque loss. It is found from the simulation results that the fuel economy by the modified ratio control algorithm is improved by 5.5 percents compared with the existing ratio control.

• 전기학회논문지P
• /
• 제57권2호
• /
• pp.121-126
• /
• 2008

This paper analyzes the losses of a Steinmetz connection three-phase induction motor which is supplied by a single-phase source. The T-type equivalent circuit which is taken no-load losses into account is used to determine phase converter capacitive reactances at starting and rated speed by using the condition of the minimum voltage unbalance. The starting and the operating capacitor are replaced at the slip of the same voltage unbalance factor points which are depicted using two capacitive reactances. The operation characteristics are investigated by comparing with those of three-phase balanced operation to find the feasibility of single-phase operation. To analyze the losses of this motor, the output power decrease factor(OPDF), the loss ratio(LR), the no load loss ratio(NLLR), the copper loss ratio(CLR), the stator copper loss ratio(SCLR), and the rotor copper loss ratio(RCLR) are defined and simulated in the whole slip range. The simulated results show that OPDF is maintained almost uniformly, LR is low at low speed and high at high speed, CLR is higher !ban NLLR, but CLR varies concavely and NLLR varies convexly at high speed, SCLR is low at low speed and high at high speed, but SCLR varies convexly at high speed, and RCLR is nearly opposite to SCLR.

• Earthquakes and Structures
• /
• 제10권2호
• /
• pp.429-450
• /
• 2016

An attempt has been made to incorporate the concept of collapse safety margin into the procedures proposed in the performance-based earthquake engineering (PBEE) framework for direct earthquake loss estimation, in which the collapse probability curve obtained from incremental dynamic analysis (IDA) is mathematically characterized with the S-type fitting model. The regressive collapse probability curve is then used to identify non-collapse cases and collapse cases. With the assumed lognormal probability distribution for non-collapse damage indexes, the expected direct earthquake loss ratio is calculated from the weighted average over several damage states for non-collapse cases. Collapse safety margin is shown to be strongly related with sustained damage endurance of structures. Such endurance exhibits a strong link with expected direct earthquake loss. The results from the case study on three concrete frames indicate that increase in cross section cannot always achieve a more desirable output of collapse safety margin and less direct earthquake loss. It is a more effective way to acquire wider collapse safety margin and less direct earthquake loss through proper enhancement of reinforcement in structural components. Interestingly, total expected direct earthquake loss ratio seems to be insensitive a change in cross section. It has demonstrated a consistent correlation with collapse safety margin. The results also indicates that, if direct economic loss is seriously concerned, it is of much significance to reduce the probability of occurrence of moderate and even severe damage, as well as the probability of structural collapse.

• Journal of Mechanical Science and Technology
• /
• 제15권11호
• /
• pp.1541-1547
• /
• 2001

The non-dimensional fin length for optimum heat loss from a thermally asymmetric rectangular fin is represented as a function of the ratio of the bottom surface Biot number to the top surface Biot number, fin tip surface Biot number and the non-dimensional fin width. Optimum heat loss is taken as 98% of the maximum heat loss. For this analysis, three dimensional separation of variables method is used. Also, the relation between the ratio of the bottom surface Biot number to the top surface Biot number and the ratio of the right surface Biot number to the left surface Biot number is presented.

• Journal of Magnetics
• /
• 제1권1호
• /
• pp.24-30
• /
• 1996

The relationship between effective permeability and the remanence ratio of an Fe-based amorphous alloy (Metglas 2605S3A) is investigated over a wide frequency range, in an effort to understand magnetization behavior of the alloy. In the frequency range from 1 to 200 kHz, the permeability is maximum at the remanence ratio of 0.4-0.5 and, at frequencies over 500 kHz, the correlation with negative coefficients emerges indicating that the permeability decreases with the remanent ratio, except for the ribbon coated with an insulating layer of MgO which exhibits both high values of the effective permeability and remanence ratio. It is considered from the correlation results that the boundary at which the dominant magnetization mechanism changes from domain wall motion to spin rotation is near 500 kHz. The core loss is also investigated as a function of annealing time when the samples are annealed at a fixed temperature of $435^{\circ}C$. The core loss in most cases decreases with the annealing time, the degree of the loss may consist of the hysteresis loss and anomalous eddy current loss. The two loss components are considered to be of similar magnitudes at low frequencies while, at high frequencies, the dominant contribution to the total loss is the anomalous loss.