• 한국의류학회지
• /
• 제25권2호
• /
• pp.350-357
• /
• 2001

In this study, seam strength, seam elongation and seam efficiency of polyurethane coated fabrics were examined under various sewing conditions using three kinds of fabrics, four kinds of sewing threads and three kinds of stitch lengths. And the sewability of polyurethane coated fabrics were evaluated by FAST system. The results were as follows: 1. Seam strength decreased with the increase of stitch length. The loop strength of sewing thread and the type of base fabric than the type of coated surface had an effect on seam strength. 2. Seam elongation also decreased with the increase of stitch length and was affected by the type of base fabric. The tensile elongation of polyurethans coated fabric had an effect on seam elongation. 3. Sean efficiency also was related to stitch length, the type of base fabric, and seam strength. The suitable seam efficiency was within 50%∼65% in which polyurethane coated fabric and sewing thread broke at the same time. Therefore PS thin and PPC thin sewing threads and 3mm stitch length were suitable to polyurethane coated fabrics. 4. The relaxation shrinkage(RS) of polyurethane coated fabric was smaller than the smallest value of control chart in FAST system. And the extensibility(E) and the shear rigidity(G) were larger than the largest value.

• Journal of Advanced Marine Engineering and Technology
• /
• 제33권8호
• /
• pp.1220-1225
• /
• 2009

본 논문에서는 사냑 루프 필터와 광섬유 격자 기반의 파장가변 궤환 레이저를 제안하고 있다. 다중파장을 제공하기 위하여 복굴절을 이용한 사냑 루프를 적용하였고 0.33nm의 인접 채널간격을 가지도록 제작하였다. 광섬유 격자의 열 광학 효과에 의한 파장가변을 유도하기 위하여 니크롬선을 격자위에 감았다. 파장가변과 분리에 대한 특성을 측정하기 위하여 길이가 다른 니크롬선으로 두 종류의 광섬유 격자 소자를 제작하였으며, 열 저항으로 파장가변이 되게 하였다. 광섬유격자의 반사파장이 사냑루프 다중파장의 특정 파장과 일치하면 모드 잠김현상에 의해서 공진하고 발진하게 된다. 공진파장의 이동도는 1.75pm/mW이다. 이 시스템은 전력 시스템의 전력 변동을 모니터링하는 분야에 적용할 수 있다.

• Journal of Chest Surgery
• /
• 제10권2호
• /
• pp.195-204
• /
• 1977

Dynamic lung compliance was measured in healthy ten young[mean age, 26 years] male and five young[mean age, 25 years] female. Lung volume was integrated of the rate of flow signal which was obtained by using pneumotachograph and differential pressure transducer[PM 5, Statham]. Intrapleural pressure was measured as that of intraesophagel pressure. Esophageal ballon, 15. 5cm in length, 4ml of luminal capacity and made of thin latex, was connected to the polyethylene tube that had 12-14 side holes and was of 1.5mm of ID. Transpulmonary pressure was traced by means of differential pressure transducer[PM 131, Statham] to which connected the esophageal balloon catheter and connection tube from mouth piece. Lung volume and transpulmonary pressure were photographed by cathode ray oscilloscope camera while the subjects were breathing spontaneously. Dynamic lung compliance loop was displayed on single trace monitor and subtraction was performed for the quasi-static hysteresis. Dynamic lung compliance was measured, 1. by plotting the pressure-volume relationship 2. from the subtracted pressure-volume loop. Results were as follows. 1. Dynamic lung compliances measured by plotting of healthy young male and female were $0.202{\pm}0.06$ and $0.190{\pm}0.023L/cm$ $H_2O$ respectively. 2. When measured from subtraction loop, dynamic lung compliance for male and female were $0.327{\pm}0.107$, and $0.27{\pm}0.06L/cm$ $H_2O$ respectively. 3. Dynamic chest wall and total respiratory system compliance were also measured. 4. Dynamic lung compliance by plotting appeared to be essentially same when compared to that of static compliance reported previously from our laboratory, however, that obtained from subtraction loop revealed higher values than the compliances obtained by plotting and that of static compliance.

• The Journal of Advanced Prosthodontics
• /
• 제9권6호
• /
• pp.470-475
• /
• 2017

PURPOSE. The purpose of this study was to identify the complex course of the mandibular canal using 3D reconstruction of microCT images and to provide the diagram for clinicians to help them understand at the interforaminal region in Korean. MATERIALS AND METHODS. Twenty-six hemimandibles obtained from cadavers were examined using microCT, and the images were reconstructed. At both the midpoint of mental foramen and the tip of anterior loop, the bucco-lingual position, the height from the mandibular inferior border, the horizontal distance between two points, and position relative to tooth site on the mandibular canal were measured. The angle that the mental canal diverges from the mandibular canal was measured in posterior-superior and lateral-superior direction. RESULTS. The buccal distance from the mandibular canal was significantly much shorter than lingual distance at both the mental foramen and the tip of anterior loop. The mandibular canal at the tip of anterior loop was significantly located closer to buccal side and higher than at the mental foramen. And the mental canal most commonly diverged from the mandibular canal below the first premolar by approximately $50^{\circ}$ posterior-superior and $41^{\circ}$ lateral-superior direction, which had with a mean length of 5.19 mm in front of the mental foramen, and exited to the mental foramen below the second premolar. CONCLUSION. These results suggest that it could form a hazardous tetrahedron space at the interforaminal region, thus, the clinician need to pay attention to the width of a premolar tooth from the mental foramen during dental implant placement.

• 대한기계학회논문집B
• /
• 제25권2호
• /
• pp.180-186
• /
• 2001

The condensation heat transfer coefficients of pure refrigerants R-22, R-134a, and a binary refrigerant mixture R-410A flowing in a small diameter tube were investigated. The experiment apparatus consists of a refrigerant loop and a water loop. The main components of the refrigerant loop consist of a variable-speed pump, a mass flowmeter, an evaporator, and a condenser(test section). The water loop consists of a variable-speed pump, an isothermal tank, and a flowmeter. The condenser is a counterflow heat exchanger with refrigerant flowing in the inner tube and water flowing in the annulus. The test section consists of smooth, horizontal copper tube of 3.38mm outer diameter and 1.77mm inner diameter. The length of test section is 1220mm. The refrigerant mass fluxes varied from 450 to 1050kg/(㎡$.$s) and the average inlet and outlet qualities were 0.05 and 0.95, respectively. The main results were summarized as follows ; in the case of single-phase flow, the heat transfer coefficients increase with increasing mass flux. The heat transfer coefficient of R-410A was higher than that of R-22 and R-134a, and the heat transfer for small diameter tubes were about 20% to 27% higher than those predicted by Gnielinski. In the case of two-phase flow, the heat transfer coefficients also increase with increasing mass flux and quality. The condensation heat transfer coefficient of R-410A was slightly higher than that of R-22 and R-134a. Most of correlations proposed in the large diameter tube showed significant deviations with experimental data except for the ranges of low quality and low mass flux.

• 설비공학논문집
• /
• 제14권8호
• /
• pp.656-663
• /
• 2002

Flow condensation heat transfer coefficients (HTCs) of R22, R134a, R407C, and R410A were measured on horizontal plain and microfin tubes. The experimental apparatus was composed of three main parts; a refrigerant loop, a water loop and a water/glycol loop. The test section in the refrigerant loop was made of both a plain and a microfin copper tube of 9.52 mm outside diameter and 1.0 m length. The refrigerant was cooled by passing cold water through an annulus surrounding the test section. Tests were performed at a fixed refrigerant saturation temperature of $40^{\circ}C$ with mass fluxes of 100, 200, and 300 kg/$m^2s$. Test results showed that at similar mass flux the flow condensation HTCs of R134a were similar to those of R22 for both plain and microfin tubes. On the other hand, HTCs of R407C were lower than those of R22 by 11~l5% and 23~53% for plain and microfin tubes respectively. And HTCs of R410A were similar to those of R22 for a plain tube but lower than those of R22 by 10~21% for a microfin tube. In general, HTCs of a microfin tube were 2.0~3.0 times higher than those of a plain tube.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1987년도 한국자동제어학술회의논문집(한일합동학술편); 한국과학기술대학, 충남; 16-17 Oct. 1987
• /
• pp.759-764
• /
• 1987

The design and application of optimal control technique to the rotary shearing system is mentioned in this paper. To maximize the accuracy in both shearing length and blade speed at shearing, time-varying gain patterns for closed loop control are designed on the basis of fixed terminal time constrained optimal regulator. The performance accuracy in real application has greatly improved than the conventional way of shearing control.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.131.6-131
• /
• 2001

During the operation of crane system in container yard, it is necessary to control the crane trolley position and loop length so that the swing of the hanging container is minimized. Recently an automatic control system with high speed and rapid transportation is required. Therefore, we designed a controller to control the stacking crane system.

• Journal of Magnetics
• /
• 제8권1호
• /
• pp.7-12
• /
• 2003

The method for evaluation of the particle size distribution of fine particles from hysteresis loop measurements is Presented. The method is illustrated on the SiO$_2$-based Co nanoparticle systems. The influence of technological conditions of sample preparation onto particle size distribution is investigated.

• 한국기계가공학회지
• /
• 제10권3호
• /
• pp.33-38
• /
• 2011

A cubic spline trajectory planner with arc-length parameter is formulated with estimation by summing up to the 3rd order in Taylor's expansion. The PVAJT motion planning is presented to reduce trajectory calculation time at every cycle time of servo control loop so that it is able to generate cubic spline trajectory in real time. This method can be used to more complex spline trajectory. Several case studies are executed with different values of cycle time and sampling time, and showed the advantages of the PVAJT motion planner. A DSP-based motion controller is designed to implement the PVAJT motion planning.