• Proceedings of the KSR Conference
• /
• 2007.11a
• /
• pp.51-56
• /
• 2007

Pantograph of the electric train is the important part receiving current by adhereing contact wire. Wearing rate of pantograph or contact wire is changed by the type of pantograph and material of adhering part. In special, the weather influences the relative wearing rate and wearing type of pantograph Slider and Contact wire with steep wearing in arc and life cycle of pantograph slider. Presently, the weather causes side-wearing and over-wearing of pantograph slide installed in electric train. So it is difficult to manage and operate the electric train. Although the quality of slide using in line4 vehicle was finished the test in line 2 vehicle experimentally, it has to apply after pantograph is installed in some electric trains and check the influence in it and contact wire. It is because line4 section is very different from line2 section. Experimental application is the sequence to certify the safety and abrasion resistance importantly by enlarging experimental application with increase of the experimental electric train. The lenth of line4 in Seoul Metro is 71.5[km]. It is long section. The line is mixed DC 1,500[V] section and AC 25,000[V] section. It has underground section of 41.5[km] and ground section of 30[km]. Ground section is about 42% and receives much influence in the rain during the rainy season. After experimental application we found that this pantograph slide has twice as much abrasion resistance despite a little deviation and found the occurrence probability of arc and side-wearing is decreased considerably.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.97-103
• /
• 2010

The four combustion stages in a diesel engine have close correlation among them. Especially, the ignition delay period has significant effect on the following combustion stage. And the period is also one of inevitable combustion processes in the diesel engine. For example, the diesel knocking is a well-known phenomenon due to the long ignition delay period. The interval of the ignition delay period is affected by the mixture formation process in the cylinder. However, in the case of the D.I. diesel engine, the available duration to make the mixture formation of air-fuel is very short. In addition, the means of the mixture formation mainly depends on the injection characteristics and properties of the fuel. It is difficult to make complete mixture. Therefore, an early stage of combustion is violent, which leads to the weakness of noise and vibration. In this study, using the visible engine, we measured the ignition delay period by photo sensor which detect occurrence of flame and presented the factors of the injection characteristics such as kinds of injection system, the injection pressure and the injection timing. The relation between the ignition delay period and cylinder pressure diagram which was concurrently obtained was also estimated.

• Journal of the Korean Society of Food Culture
• /
• v.31 no.5
• /
• pp.400-410
• /
• 2016

The purpose of this study was to discuss how 'milk' was produced and supplied introduced and spread in the modern Joseon period. Condensed milk and powdered milk were mainly consumed in Joseon during the Japanese colonial period since they could be conveniently preserved for a long time, although raw milk was also produced and consumed. For areas adjacent to farms, milk delivery service was offered while areas with great consumption received an additional supply from different areas by rail. Since no manufacturing plants were operational in Korea, condensed milk and powdered milk consumed in Joseon had to be imported. In the case of condensed milk, when production in Japan increased, extra supply was aggressively sent into their colony, Joseon. The 'Gyeongseong Milk Association' founded in 1937 is considered significant in that it led to standardization of the production system and prices as well as pasteurization of milk. In the late Japanese colonial era, milk production and consumption were controlled. As milk was purchased as a war supply, the milk consumption market became distorted and limited.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.1936-1942
• /
• 2009

Shinbundang-line is new Metropolitan Railway which was invested by private capital and is under construction for opening in 2010. Now Shinbundang-line pursues various innovation, for example, an express train which uses long distance of each station, and an unmanned operation. And it may be independent of existing metropolitan railway system from a viewpoint of line and fare system. So according to the present plan, Shinbundang-line will be not able to get sufficient demand because of weak connection with existing lines and monotonous function of the line. And it may be difficult to deliver various innovation which Shinbundang-line prepares to passengers. Hereupon, in this paper, I propose 3 methods for increasing competitive power of Shinbundang-line railway. First, making Shinbundang-line a trunk railway line of southern metropolitan area was proposed in relation to northern and southern extension of it. In addition connection with bus and light rail was discussed. Second, multipurpose usage of Shinbundang-line was proposed as express train and conventional passenger train in that line in addition to simple metropolitan railway. Finally, an effective operation method which Shinbundang-line must have was proposed from unmanned driving and fare system side. These methods can improve Shinbundang-line and then it will solve traffic congestion of southern metropolitan area effectively.

• Journal of the Korean Society for Railway
• /
• v.9 no.1 s.32
• /
• pp.43-49
• /
• 2006

We have evaluated the structural integrity of a sandwich composite train roof structure that can be a lightweight, cost saving solution to large structural components for rail vehicles in design stages. The sandwich composite train roof structure was 11.45 meters long and 1.76 meters wide. The finite element analysis was used to calculate the stresses, deflections and natural frequencies of the sandwich composite train roof against the weight of air-conditioned system. The 3D sandwich finite element model was introduced to examine the structural behavior of the hollow aluminum extrusion frames joined to both sides of the sandwich composite train roof. The results shown that the structural performance of the sandwich composite train roof under loading conditions specified is satisfaction and the use of aluminum reinforced frame and aluminum honeycomb core is beneficial with regard to weight saving and structural performance in comparison with steel reinforced frame and polyurethane foam core. Also, we have manufactured prototype of sandwich composite train roof structure on the basis of analysis results.

• Proceedings of the KSR Conference
• /
• 2004.10a
• /
• pp.1071-1076
• /
• 2004

The purpose. in this study. is to analyze liquefaction potential of Inchon International Airport at the Area Phase ' I ' for Railway Construction of all, seismic response was analyzed using the computer program, Shake91. Four methods proposed by Seed & Idriss. Eurocode, Iwasaki & Tatsuoka. and Ishihara were used for assessment of liquefaction potential and safety factors calculated form these methods are compared. Based on the results of seismic response analysis, the maximum acceleration at the ground surface is larger than that evaluated site factor effect by using site factor because these areas are composed of very loose sand clay. Especially, in the case of analysis with long period earthquake data. it is appeared that the acceleration of earthquake is amplified more largely. Therefore, accurate seismic response analysis is suggested for the design on the important structures on reclaimed land. The analytical results of liquefaction potential show that the increments of N-value and effective overburden pressure with remediation make safety factors increase. Through comparing the safety factors evaluated from four method, the safety factor calculated by See & Idriss method in the lowest one and it is found that the SPT N-value effect the safety factor very largely. And, Iwasaki & Tatsuoka method is affected by various factors such as average grain size. fine contents, confining pressure. In conclusion. to minimize earthquake Risk by liquefaction, the efficient remediation is essential and seismic response analysis should be carride out.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.64 no.4
• /
• pp.640-645
• /
• 2015

Near surface transit system has should be constructed as installation cost of light rail transit with elevated track. So, distance between two substations is longer than conventional system. The long feeding distance results in severe voltage drop. This paper proposes a PWM rectifier instead of diode rectifier. The PWM rectifier has some advantages. This is able to control output voltage constantly to reduce voltage drop and to use regeneration power without additional inverter. This paper analyse on improved voltage profile and cost of substation with PWM rectifier. The analysis of voltage profile use PSIM, and the installation cost of substation with PWM rectifier is compared to substation with diode rectifier.

• Structural Engineering and Mechanics
• /
• v.17 no.1
• /
• pp.113-140
• /
• 2004

A mixed eight-node hexahedral element formulated via the Hu-Washizu principle as well as the field extrapolation technique is presented. The mixed element with only three translational degrees of freedom at each node can provide extremely accurate and reliable performance for popular benchmark problems such as spacial beams, plates, shells as well as general three-dimensional elasticity problems. Numerical calculations also show that when extremely skewed and coarse meshes and nearly incompressible materials are used, the proposed mixed element can still possess excellent behaviour. The mixed formulation starts with introduction of a parallelepiped domain associated with the given general eight-node hexahedral element. Then, the assumed strain field at the nodal level is constructed via the Hu-Washizu variational principle for that associated parallelepiped domain. Finally, the assumed strain field at the nodal level of the given hexahedral element is established by using the field extrapolation technique, and then by using the trilinear shape functions the assumed strain field of the whole element domain is obtained. All matrices involved in establishing the element stiffness matrix can be evaluated analytically and expressed explicitly; however, a 24 by 24 matrix has to be inverted to construct the displacement extrapolation matrix. The proposed hexahedral element satisfies the patch test as long as the element with a shape of parallelepiped.

• Proceedings of the KSR Conference
• /
• 2006.11b
• /
• pp.791-795
• /
• 2006

Urban transit is one of the most effective ways for efficient operation and construction of an urban transit by composition system which is liked originally such as rolling-stock, power, signal and infrastructure. Urban rail transit system is running in domestic, imports major equipments from advanced countries and setup for maintenance. But it takes long time because it does each organizations and lines. Also, signal, power and track system apply different standard by each construction organizations it causes an increasing construction of cost accordingly it desperately needs a systematic countermeasure. Therefore standard specification of urban transit have been establishing and operatingfor efficient operation of urban transit and base technology security that is populace ride to become a base of state economy. After track, power and signal system will be announced. Standard specification become more, the importance of administrationof standards is emphasized more. Specification administrator’s the importance which use a computing support tool recently in railroad part in embossed and is predicted to be more such forward. Therefore we propose the effective method of management with track, power signal system by constructed data-base system.

• Proceedings of the KSR Conference
• /
• 2008.11b
• /
• pp.657-665
• /
• 2008

The main transportation mode of long distance inter-city passenger trips is high-speed rail and the modal share of transportation has been changed profoundly since the KTX service has been started in the Kyung-Bu railroad transportation corridor in the day of 1 April, 2004. After an opening of KTX service in the second stage Kyung-Bu and Ho-Nam railroad transportation corridors, a capacity of incumbent railroads will be increased and operational environments of freight train will be improved. The purpose of this paper is to examine the impact of KTX service operation on the national logistics thoroughly. This paper establishes a deceptive scheme in the national railroad logistic transportation and a route operational strategy between the main origins and destinations efficiently considering the changes of the current freight transportation system in the future. We expect to achieve efficiency of logistic transportation in this paper through alternative routes for example Ho-Nam, Chang-Hang, Seo-Hae line.