• 대한치과보철학회지
• /
• 제39권6호
• /
• pp.659-681
• /
• 2001

Platelet-rich plasma(PRP) has been known to increase the rate and degree of bone formation by virtue of growth factors in concentrated platelets. Although its great healing effect on bone defect or pre-implantation site preparation in conjunction with bone substitute has been reported, the effect associated with implant is unknown. The purpose of this study was to investigate the effect of PRP on rapid osseointegration of endosseous dental implants in the rabbit tibiae. Twenty two adult female New Zealand white rabbits, weighing approximately 2.7-3.3kg, were used for this study. Twelve of the 22 animals were used for histomorphometric analysis and ten of the 22 were for removal torque test. Each animal received two implants in each tibia (two treated with PRP and two as control) and was given fluorochrome intramuscularly. For histomorphometric analysis, rabbits were divided into four groups according to the healing period. At 1 week, 2 weeks, 4 weeks and 8 weeks postoperatively, each three animals were sacrificed serially and the amount and rate of bone formation around dental implant were examined on the undecalcified sections under fluorescent microscope, polarized microscope and light microscope connected to a personal computer equipped with image analysis system. For removal torque test, rabbits were divided into two groups and removal torque tests were performed at 4 weeks, 10 weeks after implant placement. In total, 88 screw shaped, commercially pure titanium implants (Neoplant, Neobiotech, Seoul, Korea) were used in this study. Labeling pattern reflected differences of two groups in bone formation rate at each period. Histomorphometrically, PRP group showed significantly higher bone volume within threads compared to control group at 2 weeks ($70.30{\pm}4.96%$ vs. $50.68{\pm}6.33%$; P < .01) and 4 weeks ($82.59{\pm}5.94%$ vs. $72.94{\pm}4.57%$; P < .05 ). PRP group at 1, 2 and 4 weeks revealed similar degree of bone volume formation comparable to control group at 2, 4 and 8 weeks, respectively. On the other hand, while PRP group showed higher bone-implant contact ($47.37{\pm}8.09%$) than control group ($33.16{\pm}13.47%$) at 2 weeks, there were no significant differences between PRP group and control group for any experimental period. Removal torque values also showed no significant differences between PRP group and control group at any experimental period (P > .05). These findings imply that PRP could induce rapid, more bone formation around implant during early healing period and get faster secondary stability for reducing healing period, though it has not induced bone maturation enough to resist functional loading.

• 한국세라믹학회지
• /
• 제46권1호
• /
• pp.86-93
• /
• 2009

The crack formation and the resistance of ITO film on PET substrate with a thickness of 20 nm were investigated as a function of strain. The onset strain for the increase of resistance increased with increasing strain rate, suggesting the crack initiation is dependent on the strain rate. Electrical resistance increased at the strain of 1.6% at the strain rates below $10^{-4}/sec$ while it increased at ${\sim}2%$ at the strain rates above $10^{-3}/sec$. The critical strain at which the cracks were formed is close to the proportional limit. Upon loading, the initial cracks perpendicular to the tensile axis were observed and propagated the whole sample width with increasing strain. The spacing between horizontal cracks is thought to be determined by the fracture strength and the interfacial strength between ITO and PET. The crack density increased with increasing strain. However, the effect of the strain rate on the crack density was less pronounced in ITO/PET with 20 nm ITO thickness than ITO/PET with 125 nm ITO thickness, the strength of ITO film is thought to increase as the thickness on ITO film decreases. The absence of cracks on ITO film at a strain as close as 1.5% can be attributed to the compressive residual stress of ITO film which was developed during cooling after the coating process. The higher critical strain for the onset of the resistance increase and the crack initiation of ITO/PET with a thinner ITO film (20 nm) can be linked with the higher strength of the thinner ITO film.

• Applied Biological Chemistry
• /
• 제27권
• /
• pp.3-17
• /
• 1984

Anaerobic digestion has recently attracted all over the world and Korea also shows no exception. The major benefits of anaerobic digestion are energy production, water pollution control, pathogen reduction and effective manure production. In Korea it was recognized in late sixties that there was a positive need to find alternative energy for farmers household. The main traditional energy sources in rural area were crop residues and forestry products. Therefore Office of Rural Development through its Rural Guidance Bureau disseminated about 29,000 household biogas units from 1969 to 1975 to provide cooking fuel for farmers household and to improve the mode of farmers living standards. The units were welcomed by farmers at that time. Now, however, most of them are not using due to a number of reasons associated with cold winter and some techno-economical problems (in those day, fossil fuel was quite expensive to compare with other prices and since then farmers income was quickly increased). The author studied on bag type household biogas plant to solve some technical problems of existing household biogas plants, but this also has little appeal for the farmers. From 1977 author studied on village scale biogas plant with two pilot plants. From the viewpoint of energy production, COD removal, kill rate of pathogen and fertilizer value, the results obtained from the experiments were quite promising, but the construction cost of the village scale biogas plant was too high for the farmers in Korea. To find most suitable biogas plant for farmers in Korea through the simplifying the biogas digester, the author developed batch-load biogas plant. By feeding coarse crop residues and manures, total solids concentrations of the batch-load biogas plant are about 28 percent which is much higher than continous digester of 5-8 percent. The batch-load biogas plant was welcomed by many farmers in Korea when it was reported on TV and newspapers. The plant was disseminated 154 units in 1982, 766 units in 1983 and 812 units in 1984 as a promissing project. Besides these biogas plant experiments, studies were also conducted 1) to determine gas production rate with agricultural wastes, 2) to evaluate the effect of loading rate, dilution, retention time on biogas production, 3) to project the amount of potencial energy from agricultural wastes.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 1995년도 춘계학술대회논문집; 전남대학교, 19 May 1995
• /
• pp.196-201
• /
• 1995

The broadband and discrete sources of sound in small cooling fans of propeller type and centrifugal type were investigated to understand the turbulent vortex structures from many bladed fans using ANSI test plenum for small air-moving devices (AMDs). The noise measurement method uses the plenum as a test apparatus to determine the acoustic source spectral density function at each operating conditions similar to real engineering applications based on acoustic similarity laws. The characteristics of fans including the head rise vs. volumetric flow rate performance were measured using a performance test facility. The sound power spectrum is decomposed into two non-dimensional functions: an acoustic source spectral distribution function F(St,.phi.) and an acoustic system response function G(He,.phi.) where St, He, and .phi. are the Strouhal number, the Helmholtz number, and the volumetric flow rate coefficient, respectively. The autospectra of radiated noise measurements for the fan operating at several volumetric flow rates,.phi., are analyzed using acoustical similarity. The rotating stall in the small propeller fan with a bell-mouth guided is mainly due to a leading edge separation. It creates a blockage in the passage and the reduction in the flow rate. The sound power levels with respect to the rotational speeds were measured to reveal the mechanisms of stall and/or surge for different loading conditions and geometries, for example, fans installed with a impinging plate. Lee and Meecham (1993) studied the effect of the large-scale motions like impinging normally on a flat plate using Large-Eddy Simulation(LES) and Lighthill's analogy.[ASME Winter Annual Meeting 1993, 93-WA/NCA-22]. The dipole and quadrupole sources in the fans tested are shown closely related to the vortex structures involved using cross-correlations of the hot-wire and microphone signals.

• Steel and Composite Structures
• /
• 제35권3호
• /
• pp.439-447
• /
• 2020

This paper presents two sets of full three-dimensional thermoelastic finite element analyses of superimposed thermo-mechanically loaded Spar Wingskin Joints made with laminated Graphite Fiber Reinforced Plastic composites. The study emphasizes the influence of residual thermal stresses and material anisotropy on the inter-laminar delamination behavior of the joint structure. The delamination has been pre-embedded at the most likely location, i.e., in resin layer between the top and next ply of the fiber reinforced plastic laminated wingskin and near the spar overlap end. Multi-Point Constraint finite elements have been made use of at the vicinity of the delamination fronts. This helps in simulating the growth of the embedded delamination at both ends. The inter-laminar thermoelastic peel and shear stresses responsible for causing delamination damage due to a combined thermal and a static loading have been evaluated. Strain energy release rate components corresponding to the Mode I (opening), Mode II (sliding) and Mode III (tearing) of delamination are determined using the principle of Virtual Crack Closure Technique. These are seen to be different and non-self-similar at the two fronts of the embedded delamination. Residual stresses developed due to the thermoelastic anisotropy of the laminae are found to strongly influence the delamination onset and propagation characteristics, which have been reflected by the asymmetries in the nature of energy release rate plots and their significant variation along the delamination front.

• 한국안전학회지
• /
• 제28권1호
• /
• pp.12-17
• /
• 2013

Considering the wind power system and the rotor blades which are composed of much technology, the wind power blade would be the most dangerous part because it revolves at high speed and weighs about dozens of tons, if the accident happens. Therefore, the light weight composite materials have been replacing as substitutional materials. The object of this study is to examine the delamination and damage for CFRP/GFRP hybrid composite that is used for strength improvement of a wind power blade. The influence of the initial crack length and fiber orientation for the interlaminar delamination was exposed for the blade safety. Plain woven CFRP instead of GFRP was inserted into the layer of the box spar for improving the strength and blade life. DCB(Double Cantilever Beam) specimen was used for evaluating fracture toughness and damage evaluation of interlaminar delamination. The material used in the experiment is a commercial material known as CF 3327 EPC in plain woven carbon prepreg(Hankuk Carbon Co.) and UD glass fiber prepreg(Hyundai Fiber Co.). From the results, crack growth rate is not so different according to the variation of the initial crack length. Mode I interlamainar fracture toughness of fiber direction $0^{\circ}$ is higher than that of $45^{\circ}$. Interlaminar fracture has an effect on fiber direction and K decreased with lower value according to increasing initial crack length. Also energy release rate fracture toughness was evaluated because CFRP/GFRP hybrid composite with a different thickness is under the mixed mode loading condition. The interlaminar fracture was almost governed by mode I fracture even though the mixed mode.

• 한국수정란이식학회지
• /
• 제14권3호
• /
• pp.145-153
• /
• 1999

This study was conducted to investigate the effects of vitrification solution and developmental stage on the survival rate of vitrified-thawed human blastocyst embryos. Human blastocyst embryos were cryopreserved by vitrification using EFS and GE solution, and their survival rates were examined after thawing and further culture. EFS solution was consisted of 40% ethylene glycol, 18% Ficoll 70 and 0.3M sucrose. GE solution was consisted of 25% glycerol and 25% ethylene glycol. Embryos were exposed to EFS and GE solution by 2 steps and 3 steps, respectively, and plunged into liquid nitrogen after loading into 0.25ml plastic straws. Blastocysts were classified into 4 groups in accordance with their developmental stage: into 1) EEB, 2) MEB and 3) EdB, of blastocysts developed on day 5, and 4) 6d-Bla(the blastocysts which formed on day 6). The blastocysts at each stage were vitrified by GE solution and cryopreserved in LN2. After thawing them, we examined their survival rates, respectively. The resulted of this study were as follows: 1. The survival rate of blastocysts vitrified by GE solution was 64.4%, significantly higher than that (5.7%) vitrified by EFS solution (P<0.001). 2. When the blastocysts were vitrified by GE solution according to each developmental stage, the survival rates of EEB, MEB, EdB and 6d-Bla were 65.9%, 65.9%, 73.2% and 58.1%, respectively. In conclusion, the cryopreservation of human blastocysts by vitrification is likely to have a marked advantage in terms of cost, work and time as compared to the conventional slow freezing in IVF-ET programs.

• 한국재료학회지
• /
• 제19권1호
• /
• pp.1-6
• /
• 2009

In this study, the stress-strain response and the cracking behaviors of ITO film on a PET substrate are investigated. The cracking behaviors of ITO thin films deposited on a thermoplastic semi-crystalline polymer developed for flexible display applications was investigated by means of tensile experiments equipped with an electrical measurement apparatus and an in-situ optical microscope. Electrical resistance increased gradually in the elastic-to-plastic transition region of the stress strain curves and cracks formed. Numerous cracks were found in this region, and the increase of the resistance was linked to the cracking of ITO thin films. Upon loading, the initial cracks perpendicular to the tensile axis were observed at about 1% of the total strain. They propagated to the entire sample width as the strain increased. The spacing between the horizontal cracks is thought to be determined by the fracture strength and the thickness of the ITO film as well as by the interfacial strength between the ITO and PET. The effect of the strain rate on the cracking behavior was also investigated. The crack density increased as the strain increased. The spacing between the horizontal cracks (perpendicular to the stress axis) increased as the strain rate decreased. The increase of the crack density as the strain rate decreased can be attributed to the higher fraction of the plastic strain to the total strain at a given total strain. The higher critical strain for the onset of the increase in the resistance and the crack initiation of the ITO/PET with a thinner ITO film (300 ohms/sq.) suggests a higher strength of the thinner ITO film.

• Composites Research
• /
• 제19권4호
• /
• pp.1-6
• /
• 2006

PSF/AS4 복합재 적층구조의 가속노화가 피로강도에 미치는 영향을 변분이론을 이용한 에너지 발산율(energy release rate) 분석을 이용하여 연구하였다. 변분이론 분석은 수지미소균열에 대한 파괴역학을 해석하는데 사용되어 왔으며 이 논문에서는 피로하중 하에서 가속노화 시간에 따르는 파괴인성이 어떻게 변하는가를 설명하였다. 수정된 Paris 법칙에 의한 선도는 각 재료마다. 미소균열이 형성되는 특성을 나타낸다. PSF/AS4 $[0/902]_s$ 적층구조가 60일 동안 유리천이온도에 근거를 두고 세분한 4개의 각기 다른 온도로 가속노화를 하였다. 모든 온도에서 파괴인성은 가속노화 시간에 따라 감소하였다. 높은 온도에서의 파괴인성의 감소는 낮은 온도에서의 감소보다 빠르게 진전되었다. 가속노화가 피로강도에 미치는 영향을 파악하기 위해 유리 천이온도인 섭씨 180도에 가까운 170도에서 60일 동안 노화한 것과 노화하지 않은 것을 비교하였다. 노화된 시편에 대하여 파괴인성의 변화(${\Delta}G_m$)가 낮은 값에서 미소균열이 형성되는 것을 알 수 있었다.

• 한국터널지하공간학회 논문집
• /
• 제12권5호
• /
• pp.349-358
• /
• 2010

대부분의 터널은 시간이 지남에 따라 유입량 증가, 작용수압의 변화 등 지하수의 영향을 받는다. 이러한 수리영향에 대응하기 위하여 터널 시공 시 지하수의 유입과 라이닝의 간극수압을 줄이기 위한 그라우팅을 적용한다. 본 연구에서는 효과적인 그라우팅을 위해 수치 해석결과를 바탕으로 다양한 그라우팅 조건에 대한 영향을 분석하였다. 그라우팅 영향 특성을 분석하기 위하여 그라우팅의 상대 투수계수 해석, 그라우팅의 두께, 그라우팅의 거리 등을 영향요소로 다르게 하였다. 해석결과는 지반하중, 수압, 라이닝 위치에 따른 수압, 라이닝 주변 수압분포, 유입량으로 나누어서 고찰하였다. 라이닝의 작용하는 지반 하중은 모든 조건에서 거의 동일했으며, 라이닝에 작용하는 수압은 그라우팅의 투수계수가 감소할수록, 두께가 증가할수록, 그라우팅 영역 거리가 가까울수록 감소하였다 유입량은 그라우팅 투수계수가 작을수록 감소하며, 그라우팅 두께와는 반비례한다. 본 그라우팅 영향 평가를 활용하여 지반 조건에 따른 그라우팅의 효과적인 적용을 할 수 있다.