• Wind and Structures
• /
• 제1권4호
• /
• pp.303-315
• /
• 1998

Full-scale measurements have been made to determine the increase in wind speed over two exposed embankments, one of $23^{\circ}$ slope and 4.7 m in height, the other of $24^{\circ}$ slope and 7.3 m in height. Measurements were made at heights of 5, 10 and 15 m above the upper edge of each embankment and at the same heights approximately 100 m upwind in the lower-level approach fetch. Despite the modest sizes of the embankments, the maximum recorded increase in mean wind speed was 28% and the minimum was 13%; these increase relate to increases in wind loads on structures erected at the top of the embankments of 64% and 28% respectively. The associated increases in gust speeds are estimated at 33% and 18%, which imply increases in gust loading of 77% and 39% respectively. These experimental results are compared with predictions obtained from a computational fluid dynamics (CFD) analysis, using three high Reynolds number eddy-viscosity models and estimates from the UK wind loading code, BS 6399: Part 2. The CFD results are generally in agreement with the experimental data, although near-ground effects on the embankment crest are poorly reproduced.

• 한국구조물진단유지관리공학회 논문집
• /
• 제25권2호
• /
• pp.66-73
• /
• 2021

유공 강재보에 대한 기존연구는 개구부의 위치가 강재보의 지지점까지의 이격이 보 단면 높이 이상인 경우가 다수이다. 유공 강재보의 개구부를 사용하는 덕트 및 배관 등의 설비시설의 배치를 고려할 때, 개구부는 강재보 지지점까지 이격이 보 단면 높이보다 가까운 경우가 있으므로 이에 대한 연구의 필요성이 대두된다. 본 연구는 지지점에 근접하게 개구부가 설치된 유공 강재보에 반복하중 가력에 따른 구조성능을 파악하는 실험연구이다. 또한 유공 강재보에 수직·수평 강판을 이용한 개구부 보강에 대하여 실험을 통하여 보강성능을 파악하고자 한다.

• Nuclear Engineering and Technology
• /
• 제55권3호
• /
• pp.876-883
• /
• 2023

Radioactive waste should be solidified before being disposed of in the repository to eliminate liquidity or dispersibility. Cement is a widely used solidifying media for radioactive waste, and cement solidified waste should satisfy the minimum compressive strength of the waste acceptance criteria of a radioactive repository. Although the compressive strength of waste should be measured by the test method provided by the waste acceptance criteria, the method differs depending on the operating repository of different countries. Considering the measured compressive strength changes depending on test conditions, the effect of test conditions should be analyzed to avoid overestimation or underestimation of the compressive strength during disposal. We selected test conditions such as the height-to-diameter ratio, loading rate, and porosity as the main factors affecting the compressive strength of cement solidified radioactive waste. Owing to the large variance in measured compressive strength, the effects of the test conditions were analyzed via statistical analyses using parametric and nonparametric methods. The results showed that the test condition of the lower loading rate, with a height-to-diameter ratio of two, reflected the actual cement content well, while the porosity showed no correlation. The compressive strength assessment method that reflects the large variance of strengths was suggested.

• Journal of Korean Dental Science
• /
• 제17권1호
• /
• pp.45-52
• /
• 2024

Purpose: To investigate the 5-year outcome of dental implants placed in a grafted maxillary sinus using recombinant human bone morphogenetic protein-2 (rhBMP-2). Materials and Methods: We retrospectively analyzed 27 implants after maxillary sinus floor augmentation (MSFA) using rhBMP-2 in 16 patients between January 2016 and March 2017. The study evaluated two outcome variables: (1) 5-year cumulative survival and success rate of the implant after functional loading and (2) marginal bone loss (MBL) for implant failure. Results: The average residual bone height was 4.78±1.53 mm. The healing period before loading was 8.35±2.34 months. The crown-to-implant ratio was 1.31±0.26. The 5-year cumulative survival and success rate after functional loading were 100% and 96.3%, respectively. The 5-year average MLB was 0.89±0.82 mm. Conclusion: Placing dental implants with MSFA using rhBMP-2 is a reliable procedure with favorable long-term survival and success rates.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1994년도 가을 학술발표회 논문집
• /
• pp.47-54
• /
• 1994

Full-scale and 1:15 scale fluid model experiments of roof ballast pavers are employed to optimize paver geometry and study wind loading and performance of roof ballast pavers. Wind pressures above and beneath pavers are conducted for buildings of different heights and in different flow conditions. The effects of the side hole size and the underneath rib height under the wind loading on pavers and the effects of roof parapet height as well as flow conditions on the performance of pavers are studied. Incorporation of wind tunnel experimental results into code statements is also provided.

• Steel and Composite Structures
• /
• 제6권1호
• /
• pp.55-69
• /
• 2006

The results of tests conducted on 11 concrete-filled steel tubular columns were reported. Concrete was partially filled in circular steel tubular columns. The primary test parameters were radius and thickness of steel tubes, concrete height, loading patterns and attachment of diaphragm and studs. Concrete strain was measured directly by embedding strain gauges so that the effect of diaphragm on concrete confinement could be investigated. The effects of concrete height and diaphragm on ultimate strength and ductility of steel tubes were investigated. The comparisons of the test results with the existing results for rectangular cross-sections were made on the basis of ultimate strength and ductility of concrete-filled steel tubular columns.

• Geomechanics and Engineering
• /
• 제22권6호
• /
• pp.475-488
• /
• 2020

The recent increase in the use of Expanded Polystyrene (EPS) geofoam in construction and geotechnical projects has driven researchers to investigate its behavior, more deeply. In this paper, a series of experimental tests to investigate the stress-strain behavior and the mechanical properties of EPS blocks, under monotonic axial loading are presented. Four different densities of cylindrically shaped EPS with different dimensions are used to investigate the effects of loading rate, height and diameter, as well as the influence of the density of EPS on the stress-strain response. The results show that increasing the height of the EPS samples leads to instability of the sample and consequent lower resistance to the applied pressure. Large EPS samples show higher Young's modulus and compressive resistance due to some boundary effects. An increase in the rate of loading can increase the elastic moduli and compressive resistance of the EPS geofoam samples, which also varies depending on the density of the samples. It was also determined that the elastic modulus of EPS increases with increasing EPS density. By implementing an efficient numerical procedure, the stress-strain response of EPS geofoam samples can be reproduced with great accuracy. The numerical analysis based on the proposed method can used to evaluate the effect of different factors on the behavior of EPS geofoam.

• Tribology and Lubricants
• /
• 제35권1호
• /
• pp.37-43
• /
• 2019

This paper presents an optimization method to determine the shoulder height of an angular contact ball bearing by 3D contact analysis using nondimensional-shaped variables. The load analysis of the ball bearing is performed to calculate the internal load distributions and contact angles of each rolling element. From the results of bearing load analysis and the contact geometry between the ball and inner/outer raceway, 3D contact analyses using influence function are conducted. The nondimensional shoulder height and nondimensional load are defined to give the generalized results. The relationship between the shoulder height and radius of curvature of the shoulder under various loading conditions is investigated in order to propose a design method for the two design parameters. Using nondimensional parameters, the critical shoulder heights are optimized with loads, contact angles, and conformity ratios. We also develop contour maps of the critical shoulder height as functions of internal loads and contact angles for the different contact angles using nondimensional parameters. The results show that the dimensionless shoulder height increased as the contact angle and dimensionless load increased. Conversely, when the conformity ratio increased, the critical shoulder height decreased. Therefore, if the contact angle is reduced and the conformity ratio is increased within the allowable range, it will be an efficient design to reduce the shoulder height of ball bearings.

• Restorative Dentistry and Endodontics
• /
• 제16권1호
• /
• pp.133-150
• /
• 1991

To study the mechanical behavior depended on the restoration method and alveolar bone height at endodontically treated teeth. a finite element model was made which was applied by four types of restoration methods and alveolar bone height on upper central incisor and then 1 Kg force was applied on each model as follows; 1) $45^{\circ}$ diagonal load on incisal edge. 2) $26^{\circ}$ diagonal load on lingual surface. and 3) horizontal load on labial surface. The author analyzed the displacement and stress of teeth and their supporting tissue by finite element method according to three type of loading conditions. The results were as follows : 1. The displacement by restoration method and the stress in dentin was found greater in restoration without a post than in that with a post. 2. The displacement and stress was found about the same when compared : A) in Resin model and PFM model applied by restoration method without a post and B) in PRC model and CPC model applied by restoration method with a post. 3. The lower alveolar bone height was. the greater was the displacement and stress. 4. The lower alveolar bone height was. the greater slightly was the stress of restoration without a post than in that with a post. 5. The stress in loading condition was the greatest in P1 in dentin and post. and was greatest in P3 in alveolar hone. 6. In the restoration method without a post. stress concentration in labial dentin was distributed to a figure of long belt in adjacent part to periodontal ligament. while in restoration method with a post. it was distributed in adjacent part to post side. And in all types of restoration method stress concentration in alveolar bone was distributed along the compact bone of labial and lingual surface.

• Composites Research
• /
• 제20권5호
• /
• pp.26-33
• /
• 2007

본 논문에서는 풀아웃 하중과 전단하중을 받는 복합재 샌드위치 인써트 조인트의 강도 특성을 실험으로 연구하였다. 샌드위치의 면재는 탄소 평직, 심재는 노멕스 하니콤, 접착제는 FM73을 사용하여 동시성형으로 제작하였다. 코어의 높이와 밀도, 면재의 두께, 하중의 형태를 달리하여 10종류, 총 75개의 인써트 조인트에 대한 실험을 수행하였다. 실험 결과, 풀아웃 하중에서는 코어의 높이와 밀도가 모두 파손하중에 영향을 미치지만 밀도의 영향이 상대적으로 더 크게 나타났다. 전단하중의 경우 면재의 두께가 파손하중에 결정적인 영향을 미치는 반면, 코어의 높이는 큰 영향을 미치지 않는 것으로 나타났다. 동일한 치수의 조인트에서도, 포팅된 쎌의 수에 따라 파손하중은 달라지며, 특히 풀아웃 하중에서 그러한 특성이 현저하게 나타났다.