• 농업과학연구
• /
• 제4권1호
• /
• pp.88-93
• /
• 1977

흙의 압밀시험(壓密試驗)에서 하중증가율(荷重增加率)을 변화(變化)시켰을 때 압밀(壓密)의 제계수에 미치는 영향을 고찰하기 위하여 표준압밀시험(標準壓密試驗)에서 적용하는 전하량(戰荷重) 증가율(增加率)을 여러가지로 변경(變更)하여 압밀시험(壓密試驗)을 실시(實施)하여 다음과 같은 결과(結果)를 얻었다. 하중증가율(荷重增加率)이 클수록 침하량(沈荷量)은 크나 팽창량(膨脹量)은 하중증가율(荷重增加率)과 무관(無關)하다. 일침압밀(一沈壓密) 완자점(完子點)까지의 시간은 하중증가율(荷重增加率)이 작을수록 큰 값을 나타냈고, 또 과압밀 영역에서는 하중증가(荷重增加)에 따라 일침압밀완자점(一沈壓密完子點)의 시간(時間)은 큰 값을 나타내고 정규압밀(正規壓密)영역에서는 거의 일정(一定)한 값을 나타냈다. 압밀계수(壓密係數)는 재하량(載荷重)이 증가(增加)함에 따라 감소(減少)하며 하중증가율(荷重增加率)이 클수록 압밀계수(壓密係數)의 값도 크게 나타났다. 이침압밀비(二次壓密比)의 값은 곡연(曲緣)의 변곡점(變曲點)과 거의 일치(一致)되는 점(點)에서 최대(最大)로 되었다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 춘계학술대회 논문집
• /
• pp.613-618
• /
• 2004

Is confirming safety of derailment when wish to develop new vehicles or upgrade running speed of vehicles. This means the measure of wheel load and lateral force that act between wheel and rail. So far, problem in continuous measuring method of derailment coefficient was sensitivity decline and noise growth. This research supplemented these problems by composition of new bridge circuit.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 춘계학술대회 논문집
• /
• pp.504-509
• /
• 2005

Railway noise and vibration has been recognized as major problems with the speed-up of rolling stock. As a kind of solution to these problems, the decrease of stiffness of track pad have been tried. However, in this case, overturning of rail due to lateral force should be considered because it can have effect on the safety of running train. Therefore, above two things - decrease of stiffness of track pad and overturning of rail due to lateral force - should be considered simultaneously for the appropriate determination of spring coefficient of track pad. With this viewpoint, minimum spring coefficient of track pad is estimated through the comparison between the theoretical relationship about the overturning of rail and 3-dimensional FE analysis result. Two kinds of Lateral force and wheel load are used as input loads. Extracted values from the conventional estimation formula and the Shinkansen design loads are used. It is found that the overturning of rail changes corresponding to the change of the stiffness of track pad and the ratio of lateral force to wheel load. Moreover, it is found that the analysis model can have influence on the results. Through these procedure, minimum spring coefficient of track pad is estimated.

• 한국윤활학회:학술대회논문집
• /
• 한국윤활학회 2003년도 학술대회지
• /
• pp.368-376
• /
• 2003

In this research, DLC thin films are produced as several hundred nm thickness by PE-CVD method. And then these thin films are estimated tribological characteristics to find out useful possibilities as a protecting film for high-quality function and life extension at MEMs by mechanical properties observation . These are measured thickness and residual stress of DLC coating. Compared after measuring friction coefficient, adhesion force, hardness, cohesive force of coating films. As results all test, we can decide several conclusions. First, friction coefficient decreased, as the load increased. otherwise, friction coefficient increased, as thickness of coating film increased under low load$(1\~50mN)$. Secod, adhesion force increased as thickness of coating films. Third, hardness of coating film is affected by substrate coating film when it is less than thickness of 300nm and it has general hardness of DLC coating film when it is more than thickness of 500nm. Fourth, cohesive force of coating film is complexly affected by hardness, adhesion force, residual stress, etc.

• 한국생산제조학회지
• /
• 제25권4호
• /
• pp.301-306
• /
• 2016

High speed polishing can kinematically increase the polishing removal rate by using the conventional Preston equation, especially for hard substrates such as sapphire or diamond. However, high speed effects should be clarified beforehand considering the lubrication state and process parameter variations. In this paper, we developed a polishing experimental method and apparatus to determine the lubrication state by measuring the real time friction coefficient using two load cells. Through experiments, we obtained a boundary lubrication state above 0.35 of the friction coefficient by using low table speed and high polishing load, indicating a synchronized stable behavior in polishing head rotation. However, larger Stribeck indexes by a high speed above 200 rpm can generate a hydrodynamic lubrication state below 0.25 of the low friction coefficient. This causes the polishing head rotation to stop. A forced and synchronized head rotation is required for high speed polishing.

• Journal of Power Electronics
• /
• 제19권2호
• /
• pp.580-590
• /
• 2019

The concept of virtual synchronous generators (VSGs) is a valuable means for improving the frequency stability of microgrids (MGs). However, a great virtual inertia in a VSG's controller may cause power oscillation, thereby deteriorating system stability. In this study, a small-signal model of an MG with two paralleled VSGs is established, and a control strategy for maintaining a constant inertial time with an increasing active-frequency droop coefficient (m) is proposed on the basis of a root locus analysis. The power oscillation is suppressed by adjusting virtual synchronous reactance, damping coefficient, and load frequency coefficient under the same inertial time constant. In addition, the dynamic load distribution is sensitive to the controller parameters, especially under the parallel operation of VSGs with different capacities. Therefore, an active power increment method is introduced to improve the precision of active power sharing in dynamic response. Simulation and experimental is used to verify the theoretical analysis findings.

• Wind and Structures
• /
• 제36권4호
• /
• pp.249-261
• /
• 2023

Aerodynamic force coefficients are generally prescribed by an ensemble average of ten and/or twenty 10-minute samples. However, this makes it difficult to identify the exact probability distribution and exceedance probability of the prescribed values. In this study, 12,600 10-minute samples on three tall buildings were measured, and the probability distributions were first identified and the aerodynamic force coefficients corresponding to the specific non-exceedance probabilities (cumulative probabilities) of wind load were then evaluated. It was found that the probability distributions of the mean and fluctuating aerodynamic force coefficients followed a normal distribution. The ratios of aerodynamic force coefficients corresponding to the specific non-exceedance probabilities (C_f,Non) to the ensemble average of 12,600 samples (C_f,Ens), which was defined as an adjusting factor (C_f,Non/C_f,Ens), were less than 2%. The effect of coefficient of variation of wind speed on the adjusting factor is larger than that of the annual non-exceedance probability of wind load. The non-exceedance probabilities of the aerodynamic force coefficient is between P_C,nonex = 50% and 60% regardless of force components and aspect ratios. The adjusting factors from the Gumbel distribution were larger than those from the normal distribution.

• 신재생에너지
• /
• 제20권2호
• /
• pp.17-25
• /
• 2024

In this study, the effect of the time step specified in a computational fluid dynamics (CFD) simulation on load response is analyzed and the drag coefficients of the floating body of floating offshore wind turbines (FOWTs) are estimated. By evaluating the error in the FOWT load response and the change in the drag-coefficient values based on the density of the time intervals, this study aims to establish a time-interval setting that minimizes the time and cost of CFD simulations for selecting drag-coefficient values. Practical CFD utilization strategies necessary for the calibration of medium-to high-fidelity analysis tools are presented. Based on a comparative analysis of CFD simulations conducted at various time intervals, the results confirmed that under a certain time interval that sufficiently considers various factors, the accuracy of the FOWT response with respect to density shows minimal differences, thereby providing an efficient utilization method for CFD simulations in FOWT design and analysis.

• 농업과학연구
• /
• 제10권1호
• /
• pp.110-117
• /
• 1983

본(本) 연구(硏究)는 쌍곡선법(雙曲線法)을 이용(利用)해서 하중(荷重) 증가율(增加率)이 이차압밀(二次壓密)에 마치는 영향(影響)을 구명(究明)하기 위하여, 아산만(牙山灣)의 해성점토(海成粘土)에 대(對)하여 시험(試驗)한 것으로 그의 결과(結果)를 요약(要略)하면 다음과 같다. 1. 쌍곡선법(雙曲線法)에 의(依)한 이차압밀량산정(二次壓密量算定) 값은 Casagrande의 log t 법(法)에 의(依)한 값보다 약간 작았으나, 그 차이(差異)는 미소(微小)하였고 쌍곡선법(雙曲線法)으로는 하중(荷重) 증가율(增加率)이 작을 때에도 쉽게 이차압밀량(二次壓密量)을 산정(算定)할 수 있었다. 2. 하중증가율(荷重增加率)이 작을수록 이차압밀비(二次壓密比)는 크게 나타났으며 하중증가율(荷重增加率)이 작을때 일어나는 심하곡선(沈下曲線)의 creep 현상(現象)은 이차압밀(二次壓密)에 기인(起因)한 것이라 생각된다. 3. 일차압밀중(一次壓密中)에 생기는 이차압밀(二次壓密)는 과압밀영역(過壓密領域)에서는 불규칙(不規則)했으나, 과압밀영역(過壓密領域)에서는 하중증가율(荷重增加率)이 작을수록 증가현상(增加現象)을 보였다. 4. 이차압밀계수(二次壓密係數)는 하중(荷重)의 증가(增加)에 따라 점차 증가(增加)하여 선행하중근처(先行荷重近處)에서 변곡점(變曲点)을 이루었고 하중(荷重)이 $2kg/cm^2$부터는 감소현상(減少現象)을 나타냈으며 이차압밀계수(二次壓密係數)는 하중증가율(荷重增加率)과 무관(無關)함을 보였다. 5. 이차압밀계수(二次壓密係數)와 압축지수(壓縮指數)는 비례관계(比例關係)를 나타냈다.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2008년도 하계학술발표대회 논문집
• /
• pp.853-856
• /
• 2008

Windows have an great effect on annual building load because windows are the weakest parts of building envelope thermally. To reduce the consumption of building energy, the thermal performance of window has to be improved in first place. Therefore this research aims to make a quantitative analysis of the heating and cooling load according to the window thermal performance using the heat load simulation program. As a result of the simulation, annual heat load is down 38% according to the decrease of U-value of window, 1.00 W/$m^2K$. and annual heat load is up 10% according to the decrease of shading coefficient, 0.20. The annual load of the window with Low-E glass is 15% lower than the window with pair glass.