• 제목/요약/키워드: load and resistance factors

검색결과 230건 처리시간 0.031초

국내 통계자료를 이용한 설계기준의 하중저항계수 검증 (Calibration of Load and Resistance Factors in KCI Code Based on Domestic Data)

  • 김지상;김종호
    • 콘크리트학회논문집
    • /
    • 제23권4호
    • /
    • pp.495-501
    • /
    • 2011
  • 2007년 개정된 콘크리트구조설계기준에서 제시하고 있는 강도설계법의 하중 조합은 ACI 318-05 기준의 하중저항계수설계법(LRFD)을 참고하여 작성된 것이다. LRFD는 하중계수와 저항계수의 조합으로 이루어져 있고, 이 계수들의 선정은 대상 파괴 모드에 대하여 미리 규정된 파괴 확률 또는 신뢰도 지수의 수준에 부합하여야한다. 이 때 하중계수 및 저항계수의 결정은 대상 구조물의 지역적 및 시대적 특성을 반영할 수 있는 통계 자료에 기초한 구조 신뢰성 이론에 따라 이루어져야 한다. 그러나 현재 우리나라의 설계기준은 통계자료의 많은 부분을 외국의 연구 결과에 의존하고 있는 실정이다. 이를 개선하기 위하여 이 연구에서는 지금까지 국내에서 연구된 자료에 기초하여 현행 콘크리트 구조설계기준의 안전 수준을 분석하고 이에 따른 합리적인 목표 신뢰도 지수를 결정하였으며, 이를 바탕으로 국내 현실에 적합한 저항계수(강도감소계수)를 제안하였다. 이 연구의 결과는 향후 우리나라의 고유한 저항계수 및 하중계수를 개정할 때 유용한 자료로 활용될 수 있을 것으로 기대된다.

장대교량 타입말뚝에 대한 저항계수 산정 (Resistance Factor Calculation of Driven Piles of Long Span Bridges)

  • 김동욱;박재현;이준용;곽기석
    • 한국지반공학회논문집
    • /
    • 제29권4호
    • /
    • pp.57-65
    • /
    • 2013
  • 하중저항계수설계법(load and resistance factor design, LRFD)을 개발하기 위해서는 하중과 저항에 대한 신뢰성 있는 불확실성 평가가 필요하다. 기존의 말뚝기초 저항계수 산정에 관한 연구는 대부분 일반 교량에 대한 하중의 불확실성을 반영하였다. 본 연구에서는 경간장이 200m이상 300m이하인 교량과 300m이상 1500m이하인 장대 교량에 대하여 수정된 하중모델로부터 평가된 활하중 불확실성을 저항계수 산정에 반영하였다. 타입말뚝 저항을 예측하기 위하여 Imperial College Pile (ICP) 설계법을 사용하였고, 이 설계법을 적용하여 사질토 및 점성토 지반에 대한 타입 말뚝의 저항 불확실성을 평가하였다. 일반 교량에 비하여 장대교량의 경우 파괴시 발생되는 경제적, 인명적 손실이 크기 때문에 기존에 적용한 일반적인 목표신뢰수준을 더 높게 설정하였다. 장대교량에 해당하는 수정된 하중 및 목표신뢰 수준에 대하여 산정된 저항계수와 기존에 일반 교량 기초에 대하여 제시된 저항계수를 비교 분석하였다.

Reliability analysis of tunnels with consideration of the earthquakes extreme events

  • Azadi, Mohammad;Ghasemi, S. Hooman;Mohammadi, Mohammadreza
    • Geomechanics and Engineering
    • /
    • 제22권5호
    • /
    • pp.433-439
    • /
    • 2020
  • Tunnels are one of the most important constructions in civil engineering. The damage to these structures caused enormous costs. Therefore, the safe and economic design of these structures has long been considered. However, both applied loads on the tunnels as well as the resistance of the structural members are naturally uncertain parameters, hence, the design of these structures requires considering the probabilistic approaches. This study aims to determine the load and resistant factors of lining tunnels concerning the earthquake extreme events limit state function. For this purpose, tunnels that have been designed according to the previous design codes (AASHTO Tunnel LRFD 2017) and using reliability analysis, the optimum reliability of these structures for different loading scenarios is determined. In this paper, the tunnel is considered circular. Finally, the proper load and resistance factors are calculated corresponding to the obtained target reliability. Based on the performed calibration earthquake extreme events limit state function, the result of this study can be recommended to AASHTO Tunnel LRFD 2017.

CFT 기둥의 축력비 및 압축강도 변화에 따른 화재거동 영향인자에 관한 실험적 연구 (An Experimental Study on the Fire Resistance effect on load ratio and compressive strength of the CFT Column under loading in fire)

  • 조경숙;김흥열;김형준;권인규;박경훈
    • 한국화재소방학회:학술대회논문집
    • /
    • 한국화재소방학회 2010년도 춘계학술논문발표회 논문집
    • /
    • pp.371-376
    • /
    • 2010
  • The strength of steel material in a concrete filled steel tube (CFT) is reduced in fire, but the filled interior concrete structurally ensures the fire resistance due to its high thermal capacity. More, the contractibility of CFT is excellent since it can be constructed without form work. This research analyzed the interior concrete strength and deformation characteristics, which are the influence factors of the fire resistance of CFT, in proportion to the axial load ratio. The fire resistance performance according to changes of the axial load ratio showed great fluctuation. As $280{\times}280{\times}6$ CFT columns with the concrete strengths of 24 MPa and 40 MPa and the axial load ratios of 0.9, 0.6, and 0.2 in accordance with KS F 2257-1 and 7 were heated with loading to examine the fire resistance performance, the 24 MPa concrete exhibited the fire resistance time as 27, 113, and 180 minutes for the axial load ratios, 0.9, 0.6, and 0.2 respectively. In case of 40 MPa concrete, the fire resistance time were turned out to be 19 and 28 minutes for the axial load ratios, 0.9 and 0.6 respectively. The results of 40 MPa concrete showed the much lower fire resistance performance when comparing with those of 24 MPa concrete. The fire resistance performance was not increased significantly when the axial load ratio was reduced. Therefore, the deceased fire resistance performance of high strength concrete is assumed to be caused by the internal pressure increase upon the heat application.

  • PDF

Oil-Jet 윤활시 가스터어빈용 고속 Ball Bearing 윤활특성 (Lubrication Characteristics of High-Speed Ball Bearing with Oil-Jet Lubrication)

  • 김기태
    • Tribology and Lubricants
    • /
    • 제12권4호
    • /
    • pp.28-34
    • /
    • 1996
  • The lubrication characteristics of high-speed ball bearings have been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flow rates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 2969 N axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

하중일- 저항계수 설계법에 의한 철근콘크리트 구조물 최적설계 (The Optimum Design of Reinforced Concrete Structures Based on the LRFD)

  • 구봉근;강종수;김우식;김태봉
    • 콘크리트학회지
    • /
    • 제2권2호
    • /
    • pp.63-72
    • /
    • 1990
  • In this study, an optimization design of reinforced concrete structures is performed by using the structural optimization techniques based on the LRFD criteria. The target reliability index is estimated by the optimal reliability index considering the expected cost which is taken as a sum of the structural cost and the expected costs due to failure of the structure. The load and resistance factors calculated by using level I reliability theory with the target reliability index are compared for each load combination (D+L, D+L+w). The results of this study show that the resistance factors are ${\phi}_{M}$=0.90, ${\phi}_{V}$==0.70, ${\phi}_{C}$==0.65 and the load factors are 1.20D + 1.70L, 1.07L + 0.07L + 1.10W. The optimization techinques used to this study are S.L.P. The optimization design based on the LRFD criteria is more economical and rational than other criteria.

방파제 기초설계를 위한 하중저항계수의 보정(다른 형식의 상부구조 적용) (Calibration of Load and Resistance Factors for Breakwater Foundation Design. Application on Different Types of Superstructures)

  • 허정원;도안누손;맥반하;당반푸;김동현
    • 한국해안·해양공학회논문집
    • /
    • 제33권6호
    • /
    • pp.287-292
    • /
    • 2021
  • 하중·저항계수 설계는 일관된 시스템적 설계해를 제공하는 효율적인 설계 방식이다. 이 연구는 확률론적 프레임워크 내에서 방파제의 지반기초(foundation) 설계에 필요한 하중계수 및 저항계수를 결정하는 것을 목표로 하여 한국형 방파제의 대표적인 4가지 유형인 경사식 방파제, 무공케이슨 혼성식방파제, 유공케이슨 혼성식방파제, 소파블록 피복제를 대상으로 조사하였다. 파랑하중조건에서 방파제 기초의 지지력을 면밀히 조사하였다. 100,000회 샘플에 의한 Monte Carlo 시뮬레이션을 사용하여, 목표신뢰도지수(RI) 2.5와 3.0의 두 가지 수준을 선택하여 하중·저항계수의 보정을 수행하였다. 예상대로 더 높은 RI에 대해 정규화된 저항계수는 더 낮은 값을 갖는 것으로 확인되었다. 그 범위는 목표 RI 2.5의 경우 0.668~0.687이며, 목표 RI 3.0의 경우 0.576~0.634이다.

Oil-Jet Ball 윤활시 가스터빈용 고속 Ball Bearing 윤활특성

  • 김기태;권우성
    • 한국윤활학회:학술대회논문집
    • /
    • 한국윤활학회 1996년도 제24회 춘계학술대회
    • /
    • pp.86-93
    • /
    • 1996
  • The lubrication characteristics of high-speed ball bearings has been investigated empirically using 45mm bore split inner ring ball bearings employed in small industrial gas turbine engines with oil-jet lubrication method. For the close structural simulation, experiments carried out with bearing mounting supports of real engines, such as bearing housings and oil nozzle assemblies with squeeze film dampers. Thus the results of tests can be directly applied to the design and the development of gas turbine engines. Testing was done by varying operating speeds, axial load on bearings, and lubricant flowrates. During testing, the temperature of bearing at outer-ring face, the power consumption of the driving motor, and the rotating resistance of the bearing were measured. From this study, the representative factors for lubrication characteristics at high speed was found, and the most important one was not operating speed but axial load up to 1.95 million dmN speed and 303 kgf axial load. Furthermore, the detailed variation of the rotational resistance of the bearing could be visualized by measuring the change of the radial load under the bearing supports. The rotational resistance consists of the frictional resistance and the bearing-cavity oil resistance.

  • PDF

철근콘크리트 휨부재 및 압축부재의 재료조항계수 적용에 관한 연구 (Material Resistance Factors for Reinforced Concrete Flexural and Compression Members)

  • 김재홍;이재훈
    • 콘크리트학회논문집
    • /
    • 제12권2호
    • /
    • pp.21-30
    • /
    • 2000
  • In the Ultimate Strength Design, the design strength of a member is determined by multiplying the strength reduction factor to the nominal strength. This concept may be a reasonable approach, however it can not consider failure modes appropriately. Moreover, column design strength diagram show an abrupt change at a low level of axial load, which does not seem to be reasonable. This research compares the design strength determined by the strength resistance factors. As the material resistance factors for flexure and compression, 0.65 and 0.90 are proposed for concrete and steel, respectively. The design strength calculation process by applying material resistance factors addresses failure modes more effectively than by applying member strength reduction factor, and provides more resnable design strength for reinforced concrete flexural and compression members.