• Journal of Surface Science and Engineering
• /
• v.57 no.3
• /
• pp.201-207
• /
• 2024

This study compared the chemical resistance properties according to various sealing treatment methods for the anode film formed during the anodization process of Al6061 alloy. Al6061 aluminum was used in four different sealing treatment methods: boiling water sealing, lithium sealing, nickel sealing, and pressurized sealing, and each sample was evaluated for corrosion resistance through a 5% HCl bubble test and the microstructure was observed through a scanning electron microscope(SEM). According to the results, corrosion resistance increased as time and temperature increased in all sealing treatment methods. Relatively, corrosion resistance was high in the order of boiling water sealing, lithium sealing, nickel sealing, and pressure sealing, and the best corrosion resistance was found in pressure sealing. These research results can be helpful in selecting a process necessary to improve the efficiency and performance of anodizing process in the industrial field using aluminum alloys.

• Journal of Surface Science and Engineering
• /
• v.31 no.6
• /
• pp.359-370
• /
• 1998

TiAl-based intermetallic compounds were electro-bornizel in the mixture of $Na_2B_4O_7$, KCL and LiCl in the termetature rage between 850 and $1000^{\circ}C$for various times (1-5 hours)under the fixed current density of 0.5 A/$cm^2$. The optimized composition of electrolyte in this work was decided to be 76.9 wt% $Na_2B_4O_7$-19.2 wt.%(0.7KCl-0.3LiCl) -3.9 wt.% al. The samples with boronized layer were investigated by SEM, XRD and EDS. The surface micro-hardness of boronized TiAl was also evaluated using Micro Vickers Hardness Tester. The sample, boronized at $900^{\circ}C$ for 4 hours in the above composition of electrolyte under the current density of 0.5 A/$\textrm{cm}^2$, has about 36$\mu\textrm{m}$ think layer on the surface, and its surface micro-hardness was measured to be 1263 Hv. From the results of SEM, XRD and EDS, the layer consisted of $TiB_2$ sublayer and Al-oxide sub layer. Al-depleted layer below the Al-oxide sudlayer was also detected. The activation energy for formation of boronized layer in this study was calculated as 178 Kcal/moleK.

• Journal of the Korean Electrochemical Society
• /
• v.9 no.1
• /
• pp.29-33
• /
• 2006

A new porous separator based on poly(vinyl chloride) (PVC)/poly(vinylidene fluoride-co-hexafluoro-propylene) (P(VdF-co-HFP)/poly(methyl methacrylate) (PMMA) was prepared by a phase inversion method. To enhance mechanical property, the membrane was stretched uniaxially at high temperature. Tensile strength and ionic conductivity were measured for various draw ratios. The tensile strength and ionic conductivity were increased with increasing draw ratio. The tensile strength of the separator reached 52MPa after stretching to draw ratio of 5, and the ionic conductivity of the separator was increased from $1.9Xs10^{-4}S/cm\;to\;4.6X10^{-4}S/cm\;at\;25^{\circ}C$. The stretched separator immersed in liquid electrolyte was electrochemically stable up to 4.7 V. The cell based on the stretched separator was maintained at about 99% of the initial discharge capacity after 10th cycle operation at 0.2C rate.

• Journal of the Korean Chemical Society
• /
• v.42 no.2
• /
• pp.177-183
• /
• 1998

By the reactions of a $C_{2}$-chiral ligand, (+)-11S,12S-bis[2,2'-(diphenylphosphino)benzanilido]-9,10-dihydro-9,10-ethanoanthracene(6) with $[\pi-allyl chloroplatinum(II)]_4$, and $CpCo(CO)_2$ respectively, three new complexes, ($\pi$-allyl)platinum(II)(+)-11S,12S-bis[2,2'-(diphenylphosphino)benzanilido]-9,10-dihydro-9,10-ethanoanthracene perchlorate(1), ($\pi$-allyl)platinum(II)(+)-11S,12S-bis[2,2'-(diphenylphosphino)benzanilido]-9,10-dihydro-9,10-ethanoanthracene chloride(2), ($\eta^5$-cyclopentadienyl)cobalt(I)-(+)-11S,12S-bis[2,2'-(diphenylphosphino)benzanilido]-9,10-dihydro-9,10-ethanoanthracene(3) were prepared. $\eta^3$-Cyclohexenyl)palladium(II)1,2-bis(diphenylphosphino)ethane perchlorate(4) was obtained by the reaction of ($\eta^3$-cyclohexenyl)palladium(II) chloride dimer with a symmetric ligand, 1,2-bis(diphenylphosphino)ethane and lithium perchlorate. These complexes were identified by NMR-, IR-, and Mass-Spectrophotometers and elemental analyzer.

• Carbon letters
• /
• v.26
• /
• pp.18-24
• /
• 2018

Pollution of chloride ion-reinforced concrete can trigger active corrosion processes that reduce the useful life of structures. Multifunctional materials used as a counter-electrode by electrochemical techniques have been used to rehabilitate contaminated concrete. Cement-based pastes added to carbonaceous material, fibers or dust, have been used as an anode in the non-destructive Electrochemical Chloride Extraction (ECE) technique. We studied the performance of the addition of Carbon Fiber (CF) in a cement-graphite powder base paste used as an anode in ECE of concretes contaminated with chlorides from the preparation of the mixture. The experimental parameters were: 2.3% of free chlorides, 21 days of ECE application, a Carbon Fiber Volume Fraction (CFVF) of 0.1, 0.3, 0.6, 0.9%, a lithium borate alkaline electrolyte, a current density of $4.0A/m^2$ and a cement/graphite ratio of 1.0 for the paste. The efficiency of the ECE in the traditional technique using metal mesh as an anode was 77.6% and for CFVF of 0.9% it was 90.4%, with a tendency to increase to higher percentages of the CFVF in the conductive cement-graphite paste, keeping the pH stable and achieving a homogeneous ECE in the mass of the concrete contaminated with chlorides.

• 한국태양에너지학회:학술대회논문집
• /
• 2009.04a
• /
• pp.155-161
• /
• 2009

Desiccant systems have been proposed as energy saving alternatives to vapor compression air conditioning for handling the latent load. Use of liquid desiccants offers several design and performance advantages over solid desiccants, especially when solar energy is used for regeneration. The liquid desiccants contact the gas inside the packed column and the heat transfer and mass transfer will occur. This proposal is try study the mass transfer and heat transfer inside the packed column of dehumidifier and regenerator systems. And later on, the rates of dehumidification and regeneration that were affected by desiccant flow rates, air temperature and humidity, and desiccant temperature and all that variation will influence the performance of the systems.

• Proceedings of the SAREK Conference
• /
• 2009.06a
• /
• pp.639-644
• /
• 2009

This study presents the new idea of liquid desiccant system with extended surface to reduce the system size. The extended surface is inserted between vertical cooling/heating tubes to increase the mass transfer area, and the liquid desiccant flows through the tube wall and the extended surface. Mathematical models for heat and mass transfer between liquid desiccant and air stream at tube wall and extended surface are provided. Dimensionless design parameters governing heat and mass transfer phenomena around the tube and the extended surface are identifier, and dimensionless operating parameters depicting system operating condition including flow rate ratio between dehumidification/regeneration processes, and mass flow rate ratio between air stream and liquid desiccant are explained. The effects of the parameters on system performance are summarized.

• Journal of Power System Engineering
• /
• v.18 no.5
• /
• pp.55-59
• /
• 2014

This study performed experimental research to visualize the moisture content absorbed in R-22, refrigerant of refrigerator. Sulfuric acids were mixed with bromothylmol blue solution to make indicating solutions, and humidity papers were prepared by impregnation of the indicating solutions into solid supporters. Prior to the impregnation, small amount of lithium chloride was added into indicating solution. Moisture measuring cell was composed to test sensitivity of the humidity papers. Color changing characteristics of the humidity papers were also examined at various moisture contents in R-22. Color of the humidity paper varied linearly with the moisture content in R-22 in the range from 150 ppm to 300 ppm. The humidity papers showed complete color change to yellow at the moisture content of 300 ppm within 8 hours.

• Bulletin of the Korean Chemical Society
• /
• v.7 no.6
• /
• pp.472-477
• /
• 1986

The reaction of (E)- or (Z)-1-alkenylmercuric chlorides with acrylic acid derivatives in the presence of 10 mol% of lithium trichloropalladate ($LiPdCl_3$) and an equimolar amount of cupric chloride, as a reoxidant for the palladium, in acetonitrile at room temperature gave the corresponding (E,E)- or (E,Z)-2,4-dienoic acid derivatives stereospecifically in moderate to good yields. The reaction of (E)- or (Z)-3-chloromercuripropenoic acid with olefins under the reaction condintion described above similarly gave good yields of (E,E)- or (Z,E)-2,4-dienoic acids stereospecifically. A side reaction, the homocoupling of alkenylmercuric chlorides, could be minimized by employing the condition described above. However, in the reaction of 3-chloromercuripropenoic acid with olefins under the present condition, the homocoupled side reaction product was not produced.

• Journal of Integrative Natural Science
• /
• v.2 no.4
• /
• pp.289-292
• /
• 2009

Perchlorosilanes are useful precursors for the synthesis of hydrosilanes for the fabrication of electronic devices such as silicon thin-film transistors and silicon nanoparticles. For this solution process, requirements of precursors applicable to solution process are relatively low volatile and soluble in common organic solvents. In this work, the decaphenylcyclopentasilane has been obtained from the reaction of the lithium wire and dichlorodiphenylsilane. The reaction of decaphenylcyclopentasilane with lewis acid catalyst, HCl/$AlCl_3$, gives the perchlorocyclopentasilane. Decaphenylcyclopentasilane exhibits an unusual optical property. Its optical property was characterized by UV-vis and fluorescence spectroscopy. Absorption wavelength maxima for the decaphenylcyclopentasilane was 272 nm. Decaphenylcyclopentasilane displayed an emission band at 741 nm with excitation wavelength of 272 nm.