• Membrane Journal
• /
• v.13 no.4
• /
• pp.257-267
• /
• 2003

For the treatment of reactive phenolic resin waste, a simulation model of pervaporative dehydration process has been developed through hollow fiber membrane module. Some of basic parameters were determined directly from dehydration of the waste liquid through a flat sheet membrane to get realistic values. The simulation model was verified by comparing the simulated values with experimental data obtained from hollow fiber membrane module. Hollow fiber membranes with active layer coated on inside fiber were used, and feed flew through inside hollow fiber. Feed flow rate affected membrane performances and reaction by providing a corresponding temperature distribution of feed along with fiber length. Feed temperature is also a crucial factor to determine dehydration and reaction behavior by two competing ways; increasing temperature increases permeation rate as well as water formation rate. Once the permeate pressure is well below the saturated vapor pressure of feed, permeate pressure had a slightly negative effect on permeation performance by slightly reducing driving force. As the pressure approached the vapor pressure of feed, dehydration performances declined considerably due to the activity ratio of feed and permeate.

• Membrane Journal
• /
• v.26 no.4
• /
• pp.291-300
• /
• 2016

Techniques for selectively separating molecules of gas and liquid states using various separation membranes have been widely used in variety of applications such as chemical, biological, pharmaceutical, and petrochemical industries. As the nanochannel diameter, inter-channel distance and length of the nanochannel of the anodic aluminum oxide (AAO) membranes can be precisely controlled, various studies to effectively separate mixture of various molecules using AAO membrane have been widely carried out. In this study, we fabricated AAO membranes of cylindrical nanochannels of various diameter sizes and of through-hole structure, that is, nanochannels of which both ends of each nanochannel are open. Using those AAO membranes of through-hole nanochannel structure, we studied the selective permeation polymer chains dissolved in a solvent based on hydraulic volume of the polymer chains. We found a precise, quantitative relationship between the radius of gyration of polymer chains that permeated through nanochannels inside AAO membrane and the diameter of nanochannels. In addition, we demonstrate that the behavior of the polymer solution flowing through nanochannel of the AAO membrane can be successfully described with the Hagen-Poiseuille relationship. It is, therefore, possible to theoretically interpret the nanoflow of the solution flowing inside the cylindrical nanochannel.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.1
• /
• pp.9-14
• /
• 1999

The effect of operating condition was studied experimently on the characteristics of twin sprays ejected from two airblast atomizers, within the range of the mass air-fuel ratio 1.36∼3.54. Water and nitrogen gas were used as test fluids for the experiments. Spray characteristics of liquid spray were measured with measurement of mass distribution and instantaneous image of the spray cone. Experimental results show that the maximum specify of the distribution were lowered but distributed over the larger area when the ROA ratio increased, Center of mass position did not change with increasing water mass flow, Increase of the nozzle distance has an small effect on mass distribution of interaction area but distributed over the larger area. It was also conformed that the effect of interaction near central point of collision decreased with the increase of the ROA ratio on interaction area from comparison using superposition method

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.05a
• /
• pp.149-152
• /
• 2008

Effects of chamber configuration on combustion characteristic velocity of full-scale combustion chamber for 30-tonf-class liquid rocket engine were studied. The configurations of combustion chamber are ablative and channel cooling chamber (${\varepsilon}$=3.2) which have detachable mixing head, and single body regenerative cooling chamber which has nozzle expansion ratio of 3.5 and 12, respectively. The combustion chambers have chamber pressure of 53${\sim}$60 bar and propellant mass flow rate of 89 kg/s, and the injectors of all combustion chamber have recess number 1.0 and double-swirl characteristics. The hot firing test results at design point show that the combustion characteristic velocity of the regenerative cooling chamber which has nozzle expansion ratio of 12 is higher than that of other combustion chambers. The reasons for the above result are the increases of combustion pressure and enthalpy of kerosene which is heated due to cooling of the chamber wall before injection into the combustion field.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.19 no.10
• /
• pp.718-725
• /
• 2007

In the general vapor-compression refrigeration system, refrigeration lubricant circulates in refrigeration system with refrigerant. Knowledge of the amount of circulating lubricant is very important to exactly calculate capacity of the refrigeration system. An experimental study was conducted to estimate the oil concentration of a flowing $CO_2/Oil$ mixtures. POE and PAG oil are considered as test lubricants in this study. Performance tests were conducted under simulated liquid conditions for $CO_2/POE$ oil mixture in oil concentration of 0 to 10 weight-percent and $CO_2/PAG$ oil mixture in oil concentration of 0 to 6 weight-percent in the temperature ranges of $-5^{\circ}C\;to\;15^{\circ}C$. The results obtained indicate specific gravity of $CO_2/Oil$ mixture is increased as oil concentration is increased and as temperature of mixture is decreased. Oil concentration correlation of $CO_2/POE$ oil mixture and $CO_2/PAG$ oil mixture is suggested, based on the measurement of specific gravity and temperature. This correlation enable to predict the oil concentration without extraction of the mixture and can be applied for $CO_2/POE$ mixtures and $CO_2/PAG$ mixtures.

• Journal of Environmental Science International
• /
• v.11 no.8
• /
• pp.819-827
• /
• 2002

Laboratory scale experiments were conducted to evaluate the performance of a biofilter for eliminating dimethyl sulfide(DMS). A commercial compost/pine bark nugget mixture served as the biofilter material for the experiments. The gas flow rate and DMS concentration entering the filter were varied to study their effect on the biofilter efficiency. The operating parameters, such as the residence time, inlet concentration, pH, water content, and temperature, were all monitored throughout the filter operation. The kinetic dependence of the DMS removal along the column length was also studied to obtain a quantitative description of the DMS elimination. High DMS removal efficiencies(>95％) were obtained using the compost filter material seeded with activated sludge. DMS pollutant loading rates of up to 5.2 and 5.5 g-DMS/m$^3$/hr were effectively handled by the upflow and downflow biofilter columns, respectively. The macrokinetics of the DMS removal were found to be fractional-order diffusion-limited over the 9 to 25 ppm range of inlet concentrations tested. The upflow column had an average macrokinetic coefficient(K$\_$f/) of 0.0789 $\pm$ 0.0178 ppm$\^$$\sfrac{1}{2}$//sec, while the downflow column had an average coefficient of 0.0935 $\pm$ 0.0200 ppm$\^$$\sfrac{1}{2}$//sec. Shorter residence times resulted in a lower mass transfer of the pollutant from the gas phase to the aqueous liquid phase, thereby decreasing the efficiency.

• Korean Chemical Engineering Research
• /
• v.47 no.4
• /
• pp.506-511
• /
• 2009

In order to improve the bacterial cellulose(BC) production yield, centrifugal and inclined centrifugal impellers were developed. A 6 flat-blade turbine impeller was used as a control system. The flow pattern in the fermenter and volumetric oxygen transfer coefficient($k_La$) of these fermentation systems were studied. Fermentations were carried out for the production of BC by G. hansenii PJK in a 2-L jar fermenter equipped with new impellers. Liquid medium was circulated from the bottom, through the cylinder of the impeller and to the wall. The volumetric oxygen transfer coefficients, $k_La$, of inclined centrifugal and centrifugal impeller systems at 100 rpm were 23 and 15% of the conventional turbine impeller system, respectively. However, the conversion of microbial cells to cellulose non-producing mutant decreased and this results in the increase in BC production at low rotating speed of impellers.

• Journal of the Korean Ceramic Society
• /
• v.44 no.8
• /
• pp.437-444
• /
• 2007

The broth solution was prepared by the mixing of an uranyl nitrate, THFA, PVA, and water. The uranium concentration of the broth solution was $0.5{\sim}0.8$ mole-U/L and the viscosity of it was $30{\sim}80cSt$. The droplets of this broth solution were farmed in air and ammonia by the vibrating nozzle with the frequency of 100 Hz at the amplitude of $100{\sim}130V$. The diameter of the droplet was about $1900{\mu}m$ from using the nozzle diameter of 1 mm. The diameter of the aged gel was about $1400{\mu}m$ after aging in ammonia solution at $60{\sim}80^{\circ}C$, and the dried gel with the diameter of about $900{\mu}m$ was obtained after drying at room temperature or partially vacuum condition. The diameter of the calcined $UO_3$ microsphere after calcination at $600^{\circ}C$ appeared about $800{\mu}m$ in air atmosphere. Although the droplets of the same sizes were formed, the calcined microspheres of different sizes were manufactured in the case of the broth solutions of the different uranium concentration. The droplets of the desired diameters were obtained by the change of the nozzle diameters and the broth flow rates.

• Korean Journal of Oriental Medicine
• /
• v.15 no.1
• /
• pp.85-89
• /
• 2009

The aim of this study was to study the quantitative analysis of glycyrrhizic acid in Glycyrrhizae Radix extract fermented with Paecilomyces japonica, Ganoderma lucidum, honey or Nuruk. The amounts of dry on loss were measured and the quantitative analysis of glycyrrhizic acid was performed by high performance liquid chromatographic (HPLC). HPLC method was performed on C18 column ($250\;mm\;{\times}\;4.6\;mm$, $5\;{\mu}m$, RS tech) using gradient solvent mixtures of water-acetonitrile with photodiode array detector (254 nm). The flow rate was $1.0\;m{\ell}/min$. Retention time of glycyrrhizic acid was about 23.96 min and linearity of calibration was $R^2$=0.9998. Contents of glycyrrhizic acid in Glycyrrhizae Radix extract (control) was $5.048\;{\pm}\;0.14$; Contents of glycyrrhizic acid in Glycyrrhizae Radix extract fermented with Paecilomyces japonica (SDT) was $1.975\;{\pm}\;0.07$; Contents of glycyrrhizic acid in Glycyrrhizae Radix extract fermented with Ganoderma lucidum (SYT) was $2.676 \;{\pm}\;0.07$; Contents of glycyrrhizic acid in Glycyrrhizae Radix extract fermented with honey (SST) was $5.191\;{\pm}\;0.06$; Contents of glycyrrhizic acid in Glycyrrhizae Radix extract fermented with Nuruk (SNT) was $5.305\;{\pm}\;0.34$, respectively. Contents of glycyrrhizic acid in SDT and SYT were decreased but that in SST and SNT was increased when compared to control.

• Journal of ILASS-Korea
• /
• v.3 no.3
• /
• pp.33-41
• /
• 1998

In recently, a study on the lean combustion is investigated intensively, because it is expected that this method may decrease the harmful exhaust gas and improve fuel economy in gasoline engine. The problems of lean combustion system in gasoline engine are ignition difficulty, misfire and instability of combustion. The investigation on the optimization of fuel metering and the control of mixing gas flow may be critical to improve the performance of lean combustion. In the fuel injection gasoline engine, the formation of mixture influences strongly on the engine performance such that the importance of fuel metering system becomes apparent. First of all, a study on the fuel breakup characteristics of gasoline fuel injector was carried out in this paper. Fuel injectors are pintle and 4hole-2spray type. The purpose of this study is to clarify the atomization mechanism of spray injected into atomosphere field through electronic controlled-fuel injectors, and to analyze spray characteristics such as drop size distribution and mean drop diameter produced at fuel injector. In this paper, the spray development is observed by taking photograps using 80mm still-camera system, and drop sizes are measured by PMAS. From these experiment, spray pattern injected from gasoline fuel injectors was investigated clearly. Also, it was found that SMD and drop size distribution of injected fuel spray from gasoline fuel injectors.