• Korea-Australia Rheology Journal
• /
• 제16권1호
• /
• pp.47-54
• /
• 2004

Low Reynolds number, dilute, and surfactant-free bubble suspensions are prepared by mechanical mixing after introducing carbon dioxide bubbles into a Newtonian liquid, polyol. The apparent shear viscosity is measured with a wide-gap parallel plate rheometer by imposing a simple shear flow of capillary numbers(Ca) of the order of $10^{-2}$ ~ $10^{-1}$ and for various gas volume fractions ($\phi$). Effects of capillary numbers and gas volume fractions on the viscosity of polyol foam are investigated. At high capillary number, viscosity of the suspension increases as the gas volume fraction increases, while at low capillary number, the viscosity decreases as the gas volume fraction increases. An empirical constitutive equation that is similar to the Frankel and Acrivos equation is proposed by fitting experimental data. A numerical simulation for deformation of a single bubble suspended in a Newtonian fluid is conducted by using a newly developed two-dimensional numerical code using a finite volume method (FVM). Although the bubble is treated by a circular cylinder in the two dimensional analysis, numerical results are in good agreement with experimental results.

• 한국전산유체공학회지
• /
• 제10권4호통권31호
• /
• pp.12-17
• /
• 2005

A computational study of evaluation of current turbulence models is performed for a better prediction of thermal stratification in an upper plenum of a liquid metal reactor. The turbulence models tested in the present study are the two-layer model, the shear stress transport (SST) model, the v2-f model and the elliptic blending mode(EBM). The performances of the turbulence models are evaluated by applying them to the thermal stratification experiment conducted at JNC (Japan Nuclear Corporation). The algebraic flux model is used for treating the turbulent heat flux for the two-layer model and the SST model, and there exist little differences between the two turbulence models in predicting the temporal variation of temperature. The v2-f model and the elliptic blending model better predict the steep gradient of temperature at the interface of thermal stratification, and the v2-f model and elliptic blending model predict properly the oscillation of the ensemble-averaged temperature. In general the overall performance of the elliptic blending model is better than the v2-f model in the prediction of the amplitude and frequency of the temperature oscillation.

• Natural Product Sciences
• /
• 제17권4호
• /
• pp.337-341
• /
• 2011

An HPLC (high-performance liquid chromatography)-PDA (photodiode array) detection method was established for the determination of naringin, hesperidin and neohesperidin in the fruit of Citrus paradisi and C. grandis. The flavonoids were separated in less than 20 min using an YMC RP 18 column with isocratic elution using acetonitrile and water (23 : 77, v/v) at a flow rate of 1 ml/min, and a PDA detector. The levels of naringin, hesperidin and neohesperidin were 1345.92, 950.62, and 2078.82 ${\mu}g/g$, respectively, in the peel, and 102.43, 59.13, and 86.68 ${\mu}g/g$, respectively, in the flesh of C. paradisi. In C. grandis, the levels of naringin, hesperidin and neohesperidin were 3530.56, 80.00, and 5.26 ${\mu}g/g$, respectively, in the peel, and 59.59, 7.43, and 38.41 ${\mu}g/g$, respectively, in the flesh. The total content was highest in the peel, reaching 0.44% and 0.36% in C. paradisi and C. grandis, respectively, while the flesh contained only 0.025% and 0.011%, respectively. Therefore, the peels of C. paradisi and C. grandis are necessary for the processing and utilization of flavonoids.

• 생약학회지
• /
• 제48권3호
• /
• pp.226-231
• /
• 2017

Zingiberis Rhizoma (ZR, Zingiberaceae) is one of the foods for a long time and contains various biological activities including anti-cancer, anti-inflammatory, anti-oxidant, and anti-platelet activities. The present study was to compare the amount of 6-gingerol in the 70% ethanol extracts of non-processed ZR and processed ZR by roasting using a high-performance liquid chromatography equipped with photodiode array detector. The 6-gingerol was separated on a Gemini $C_{18}$ analytical column ($5{\mu}m$, $4.6{\times}250mm$) using two mobile phase consisting of distilled water and acetonitrile. The flow rate was 1.0 mL/min and injection volume was $10{\mu}L$. In non-processed ZR sample, the amount of the 6-gingerol was 0.43% and the amount of the marker compound in processed ZR samples by roasting were 0.16-0.55%.

• 한국연소학회지
• /
• 제10권1호
• /
• pp.1-6
• /
• 2005

This paper presents the combustion characteristics of hydrocarbon fuel from a conventional pressure-swirl nozzle of a small-scale burner. The nozzle has orifice diameters of 0.256 mm and liquid flow rates ranging from 50 to 64 mL/min were selected for the experiments. The furnace temperature distribution along the axial distance, the gas emission such as CO, $CO_2$, NOx, $SO_2$, flue gas temperature, and combustion efficiency were studied. The local furnace and flue gas temperatures decreased with an increase in air velocity. At injection pressures of 1.1 and 1.3 MPa the maximum furnace temperatures occurred closer to the burner exit, at an axial distance of 242 mm from the diffuser tip. The CO and $CO_2$concentrations decreased with an increase in air velocity, but they increased with an increase in injection pressure. The effect of air velocity on NOx was not clearly seen at low injection pressures, but at injection pressure of 1.3 MPa it decreased with an increase in air velocity. The effect of air velocity on $SO_2$ concentration level is not well understood. The combustion efficiency decreased with an increase in air velocity but it increased with an increase in injection pressure. It is recommended that injection pressure less than 0.9 MPa with air velocity not above 8.0 m/s would be suitable for this burner.

• International Journal of Automotive Technology
• /
• 제1권2호
• /
• pp.95-100
• /
• 2000

The droplet and the turbulent characteristics of a counterflowing internal mixing pneumatic nozzle mainly focused. The measurements were made using a Phase Doppler Particle Analyzer under the different air pressures. The nozzle with tangential-drilled holes at an angle of 30 to the central axis has been designed. The spatial distributions of velocities, fluctuating velocities, droplet diameters and SMD were quantitatively and qualitatively fluctuating velocities were substantially higher than the radial and the tangential ones. This implies that the disintegration process is enhanced with the higher air pressure. The larger droplets were detected near the spray centerline at the upstream while the smaller ones were generated at the downstream. This was attributed to the lower rates of spherical particles which were not subject to instantaneous breakup. However, substantial increases in SMD from the central part tower spray periphery were predictable in downstream regions.

• International Journal of Aeronautical and Space Sciences
• /
• 제3권2호
• /
• pp.59-66
• /
• 2002

A vertical test stand based on launcher propulsion system was constructed and several tests for the determination of cyclogram were carried out. To make an accurate estimation, static and dynamic pressures were measured and analyzed. Especially, static pressure measurements using fast response sensors without extension tubes were used to determine operation sequence more evidently. The standard operation times of final valves were determined in cold flow tests with an engine head, and fire formation time in combustion chamber was checked in an ignition test with an ignitor only. On the basis of these tests, ignition sequence was established and combustion test cyclogram was finally determined. According to combustion test, test results were well matched with the determined cyclogram within 0.05 sec.

• 한국항공우주학회지
• /
• 제31권8호
• /
• pp.99-106
• /
• 2003

본 논문에서는 액체추진로켓용 터보펌프내 초음속 충동형 터빈의 공력성능 향상을 위해 기하학적 설계변수를 수치적으로 연구하였다. 터빈의 기하학적 설계변수는 아랫면, 윗면 원호반경, 입사각, 익단두께로 설정, 적절한 구속조건을 도입하였고 목적함수로는 최대파워를 채택하였다. 목적함수를 얻기 위해 2-D Navier-Stokes 방정식과 Chien의 k-$\varepsilon$ 난류 모델링을 수치적으로 계산하였다. 초기모델에서 이형 중앙부에 흐름박리를 볼 수 있었으나 개선된 익형에서 흐름박리는 제거되었다. 본 연구를 통해 약 3.2 %의 축 파워가 증대되었다.

• Design & Manufacturing
• /
• 제7권1호
• /
• pp.60-63
• /
• 2013

Recently, Silicone that one of the thermo-sets is used to making optical products such as LED lenses because of excellent thermal properties. LED lenses are required to keep the precise dimensions, so they must be molded to have the minimum deformation. Thermo-sets have the expansion characteristic on the part of thermal property, it is important to optimize the cure condition so that the deformation of the part become minimum. In this study, to investigate the relationship between the shrinkage by the curing and expansion by the thermal properties of the resin, reactive injection experiment was performed by setting the variables such as mold setting temperature, cure time. As a result, it was confirmed that there was a interval while the thermal properties were transferred to more active during the cure process. It is expected to help in determining the reactive injection molding conditions of the thermo-set parts as well as LED lens in order to reduce the amount of deformation.

• 한국가스학회지
• /
• 제15권3호
• /
• pp.1-5
• /
• 2011

수소액화 공정은 수소 예냉 에너지, 액화에너지 그리고 Ortho/Para 변환열 제거 등 다량의 에너지가 요구되어 진다. 본 논문은 기존의 수소액화 공정에 LNG냉열을 이용하여 에너지절약 효과를 얻고자 기본설계 및 열해석을 수행하였다. 액화 소요에너지에 LNG냉열을 적용하면 수소액화공정의 에너지절약효과와 함께, LNG기지의 해수에 버려지는 LNG냉열을 회수, 이용하는 일석이조의 에너지절약기술이 된다. 열해석에 의한 설계를 수행한 결과 현재의 액체질소 예냉식 수소액화 플랜트의 소요에너지에 비하여 LNG냉열을 이용할 경우 소요동력량은 75%가 절감되었다. 이는 예냉을 액체질소 대신에 냉열을 사용하기 때문이다. 또한 LNG냉열량은 수소액화량 1T/D기준할 때 15T/D 유량이 요구되었다.