• Journal of the Korean Chemical Society
• /
• v.12 no.2
• /
• pp.65-80
• /
• 1968

The physico-chemical properties of nine selected thallium borosilicate glasses and other 21 supplementary compositions were investigated. Their composition-property curves are found to be in many respects analogous to those of other borosilicate glasses containing lithia, soda, and lead oxide. It is indicated that certain minima found in the composition-property curves of thallium borosilicate glasses might be caused by a change in boron coordination as has been observed to occur in the $Na_2O-B_2O_3-SiO_2$ glasses. Typical effects of thallium ions on the borosilicate glass are summarized as follows: 1) Addition of thallium ions increased density, refractive index, water solubility, linear coefficient of thermal expansion, and dielectric constant. 2) Increased concentration of thallium decreased the softening point of the glasses, caused fluorescence under ultraviolet radiation and smeared out the absorption edges up to $15{\mu}$ in the infrared region. An extensive liquid immiscibility was found by replication electron microscope technique in the $Tl_2O-B_2O_3-SiO_2$ system. The immiscibility covers a composition range roughly from 55 wt. % Tl2O to the binary system $B_2O_3-SiO_2.$ By acid treatment, it was found that the immiscible glass consists of separate silica-rich and boron-rich phases.

• Journal of Korea Foundry Society
• /
• v.37 no.6
• /
• pp.207-216
• /
• 2017

This study investigated the effects of the addition of Zn, Ca, and SiC on the microstructure and mechanical properties of Mg-Al alloys. The tensile properties of homogenized Mg-xAl (x = 6, 7, 8, and 9 wt.%) alloys increased with increasing Zn content by the solid-solution strengthening effect. However, when the added Zn content exceeded the solubility limit, the strength and ductility of the alloys decreased greatly owing to premature fracture caused by undissolved coarse particles or local melting. Among the Mg-xAl-yZn alloys tested in this study, the AZ74 alloy showed the best tensile properties. However, from the viewpoints of the thermal stability, castability, and tensile properties, the AZ92 alloy was deemed to be the most suitable cast alloy. Moreover, the addition of a small amount (0.17 wt.%) of SiC reduced the average grain size of the AZ91 alloy significantly, from $430{\mu}m$ to $73{\mu}m$. As a result, both the strength and the elongation of the AZ91 alloy increased considerably by the grain-boundary hardening effect and the suppression of twinning behavior, respectively. On the other hand, the addition of Ca (0.5-1.5 wt.%) and a combined addition of Ca (0.5-1.5 wt.%) and SiC (0.17 wt.%) increased the average grain size of the AZ91 alloy, which resulted in a decrease in its tensile properties. The SiC-added AZ92 alloy exhibited excellent tensile properties (YS 125 MPa, UTS 282 MPa, and EL 12.3%), which were much higher than those of commercial AZ91 alloy (YS 93 MPa, UTS 192 MPa, and EL 7.0%). The fluidity of the SiC-added AZ92 alloy was slightly lower than that of the AZ91 alloy because of the expansion of the solid-liquid coexistence region in the former. However, the SiC-added AZ92 alloy showed better hot-tearing resistance than the AZ91 alloy owing to its refined grain structure.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.12
• /
• pp.4721-4726
• /
• 2010

The performance characteristics of water-chilling heat pump using CO2 for the control of inverter frequency was investigated experimentally. An experimental apparatus is consisted of a compressor, a gas cooler, an expansion valve, an evaporator and a liquid receiver. All heat exchangers used in the test rig are counter flow type heat exchangers with concentric dual tubes, which are made of copper. The gas cooler and the evaporator consist of 6 and 4 straight sections respectively arranged in parallel, each has 2.4m length. The experimental results summarize as the following: for constant inlet temperature of evaporator and gas cooler, as mass flow rate, compression ratio and discharge pressure increases with the inverter frequency. And heating capacity and compressor work increases, but coefficient of performance(COP) decreases with the inverter frequency of compressor. As inlet temperature of secondary fluid in the evaporator increases from $15^{\circ}C$ to $25^{\circ}C$, compression ratio and compressor work decreases, but mass flow rate, heating capacity and COP increases with the inverter frequency of compressor. The above tendency is similar with performance variation with respect to the variation of inverter frequency in the conventional vapor compression refrigeration cycle.

• Journal of Mushroom
• /
• v.14 no.4
• /
• pp.136-141
• /
• 2016

The production scale of mushrooms in Korea is approximately 600 billion won, which is 1.6% of Korea's gross agricultural output. In Korea, ca. 190,000 tons of mushrooms are harvested annually. Although the numbers of mushroom farms and cultivators are constantly decreasing, total mushroom yields are increasing owing to large-scale cultivation facilities and automation. The recent expansion of the well-being trend has caused an increase in mushroom consumption in Korea: the annual per capita mushroom was 3.9 kg ('13), whichis a little higher than that in Europe. Thus, mushroom export, mainly Flammulina velutipes and Pleurotus ostreatus, has increased since the mid-2000s. Recently, however, it is slightly reduced. Nevertheless, Vietnam, Hong Kong, the United States, and the Netherlands continue to export mushrooms, and Korea has increased its export to Australia, Canada, Southeast Asia, etc. Canned Agaricus bisporus, the first export of the Korean mushroom industry, reached it speak sales in 1977-1978. When Korea initiated trade with China in 1980, the international prices of mushrooms fell sharply, leading to shrinkage of the domestic markets. Spurred by the high demand to develop substitute goods for A. bisporus, the oyster mushroom (P. ostreatus) gained attention since it seemed to suit the taste of Korean consumers. Although the log cultivation technique for oyster mushroom was developed in the early 1970s, it required a great deal of labor. Thus, we developed the shelf cultivation technique, which is easier to manage and allows for mass production. In this technique, the growing shelf is made mafrom fermented rice straw, whichis the only P. ostreatus medium in the world and isused only in South Korea. After then, the use of cotton wastes as an additional material of medium, the productivity. Currently, we are developing a standard cultivation technique and environmental control system that can stably produce mushrooms throughout the year. The increase of oyster mushroom production may boostthe domestic market and contribute to industrial development. In addition, oyster mushroom production technology played a role in forming the basis for the development of bottle cultivation, which made mass production. In particular, bottle cultivation using liquid spawn could allow for the export of F. velutipes and Pleurotus eryngii. In addition, the white varieties of F. velutipes were second developed in the world after Japan. We also developed the new A. bisporus cultivar 'Saeah', which is easy to grow in Korea. In hopes to advance the mushroom industry, we will continue to develop cultivars with international competitive power and to improve cultivation techniques.

• Korean Chemical Engineering Research
• /
• v.58 no.4
• /
• pp.651-657
• /
• 2020

Fluidization processes in which solid particles vividly move like gas or liquid have been widely used in various industrial sectors, such as thermochemical energy conversion and polymerization processes for general purpose polymer resins. One of the general purpose polymer resins, LLDPE(Linear low-density polyethylene) resins have been produced in bubbling fluidized bed processes in the world. In a bubbling fluidization polymerization reactors, LLDPE particles with relatively larger particle size and low density are fluidized by hydrogen gas for polymerization reaction. Though LLDPE polymerization reactors are one of bubbling fluidization processes, slugs that have negative impact for reaction exist or occur in these processes. Therefore, the fluidization state of LLDPE particles was investigated in a simulation model similar to a pilot-scale polymerization reactor (0.38 m l.D., 4.4 m High). In particular, the effect of gas velocity (0.45-1.2 m/s), solid density (900-199 kg/㎥), solid sphericity (0.5-1.0), and average particle size (120-1230 ㎛), on bed height and fluidization state were measured by using a CPFD(Computational particle-fluid dynamics) method. With CPFD analysis, the occurrence of a flat slug was visualized. Also, the change in particle properties, such as particle density, sphericity, and size, could reduce the occurrence of slug and bed expansion.

• Solar Energy
• /
• v.10 no.1
• /
• pp.5-13
• /
• 1990

In the present investigation, experiments and numerical analysis during melting process of a phase change material were performed to research heat transfer phenomena generated by means of conduction and natural convection in the vertical tube at inward melting. The phase change material used in the experiments is 99 percent pure n-Docosane paraffin($C_{22}H_{46}$). In the results, it is found that the velocity of phase change interface at the top of tube is faster than at the bottom of tube because of the effect of natural convection, and the distribution of velocity at the liquid region is little affected by the initial temperature of phase change material. The velocity of phase change interface is slower as the initial temperature of phase change material is lower, and the effect of natural convection is larger as the aspect ratio of tube is larger. In tendency of heat transfer phenomena, the experimental results were well corresponded with numerical results. But there were a little disagrements between the results of experiment and numerical analysis because of the assumption of the constant volumetric expansion coefficient in numerical analysis.

• Journal of Microbiology
• /
• v.45 no.5
• /
• pp.460-465
• /
• 2007

This study was carried out in order to investigate the potential of using plant oils derived from Leptospermum petersonii Bailey and Syzygium aromaticum L. Merr. Et Perry as natural antifungal agents. The antifungal effects of essential oils at concentrations of 0.05, 0.1, 0.15, and 0.2 mg/ml on the dermatophytes Microsporum canis (KCTC 6591), Trichophyton mentagrophytes (KCTC 6077), Trichophyton rubrum (KCCM 60443), Epidermophyton floccosum (KCCM 11667), and Microsporum gypseum were evaluated using the agar diffusion method. The major constituents of the active fraction against the dermatophytes were identified by gas chromatography-mass spectrometry and high-performance liquid chromatography analysis. The antifungal activities of S. aromaticum oil (clove oil) against the dermatophytes tested were highest at a concentration of 0.2mg/ml, with an effectiveness of more than 60%. Hyphal growth was completely inhibited in T. mentagrophytes, T. rubrum, and M. gypseum by treatment with clove oil at a concentration of 0.2 mg/ml. Eugenol was the most effective antifungal constituent of clove oil against the dermatophytes T. mentagrophytes and M. canis. Morphological changes in the hyphae of T. mentagrophytes, such as damage to the cell wall and cell membrane and the expansion of the endoplasmic reticulum, after treatment with 0.11 mg/ml eugenol were observed by transmission electron microscopy (TEM). At a concentration of 0.2 mg/ml, L. petersonii oil (LPO) was more than 90% effective against all of the dermatophytes tested, with the exception of T. rubrum. Geranial was determined to be the most active antifungal constituent of L. petersonii oil. Taken together, the results of this study demonstrate that clove and tea tree oils exhibited significant antifungal activities against the dermatophytes tested in this study.

• Journal of the Korean association of regional geographers
• /
• v.19 no.1
• /
• pp.75-96
• /
• 2013

This paper is to conceptualize the urban social circulation of water from the social constructivism and political ecology, and to analyze the history of development of social circulation of water, that is, the modernization process of water in Daegu. The development of social circulation system of water in Daegu can be divided into 4 stages, that is, the beginning stage of modernization of water mainly during the period of Japanese colonization, the take-off stage from the 1960s to the mid-1980s, the stage of reflexive modernization from the late 1980s to the 1990s, and that of neoliberalization of water since the 2000s. It can be seen that the development of social circulation system of water in Daegu has contributed the increasing urban population and economic development, especially supporting the spatial expansion of the city and the way of modern way of urban life. But the social circulation system of water in Daegu seems to meet with a lot of problems such as relocation of the water intake station, over-equipment of filtration plants, distrust on tap water, inequality of water use, readjustment of water charge, liquid waste from industrial complexes within the urban area, creative destruction of waterfront environment, and privatization of water.

• Fire Science and Engineering
• /
• v.32 no.6
• /
• pp.34-39
• /
• 2018

In this paper, the architecture of a safe stove with an automatic fire suppression function using a sound wave fire extinguisher has been proposed and developed for the first time. A microcontroller connected to a fire sensor detects and suppresses a fire by driving a fire extinguisher. The sound wave fire extinguisher is composed of a speaker and collimator, and is driven by a driver module including an audio amplifier. The attenuation of the sound wave is reduced by preventing the sound diffusion with an enclosure surrounding a stove. The frequency of the sound wave is set to 50 Hz, and the sound pressure of 93 dBA is measured at the distance of 0.5 m. It takes maximum 8 and 15 seconds to suppress the flame from 7-cc and 14-cc flammable liquid, respectively, which corresponds to 24% and 42% of the natural extinguishing time. Since the proposed safe stove is non-toxic and leaves no residues over the conventional ones, it would combine with various home appliances to suppress early-stage fires and prevent fire expansion.

• Korean Chemical Engineering Research
• /
• v.60 no.2
• /
• pp.175-183
• /
• 2022

With the expansion of the automobile market, the demand for Nd as an essential rare earth material for automobile motors is rapidly increasing. Research on the calcio-thermic reduction process between Nd₂O₃ and calcium-based alloys has been extensively studied in order to manufacture Nd. In this study, Ca-Cu, as a reducing for Nd₂O₃, was prepared by electrolysis in CaCl₂ molten salt. Cu wire and graphite were employed as a working electrode and a counter electrode for electrolysis reaction, respectively. The reference electrode was manufactured by putting Ag wire in a mixture of AgCl and CaCl₂ at a ratio of 1:99 mol%. The cyclic voltammetry results showed that the deposition of Ca²⁺ on the surface of working electrode was observed from a potential of -1.8 V, and the reduction potential of Ca²⁺ decreased as the reaction temperature increased. The diffusion coefficient of Ca²⁺ calculated by the chronoamperometry experiment was found to be 5.4(±6.8)×10^-6 cm²/s. In addition, Ca-Cu liquid alloy was prepared by applying a constant potential to Cu electrodes. The element ratio of Ca-Cu alloy formed by applying a potential of -2.0 V was found to Ca:Cu=1:4.