• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.30 no.1
• /
• pp.59-70
• /
• 1998

A steady-state molecular diffusion experiment was conducted to evaluate the water vapor proof properties of paper Handsheets prepared from unbleached Itraft pulps(UKP) and old newspapers(ONP) and four different types of polymer-laminated white duplex board were tested under appropriate standard conditions. The diffusivity was determined on the basis of the Fickean first law. Results obtained from this study can be summarized as follows ; 1. The diffusivity data for handsheets showed about $10^{-5}cm^2/min$. whereas polymer-laminated paperboards had remarkably improved water-vapor resistance with about $10^3 to 10^4$ times lower diffusivity : 2. Sheet basis weight, wet-swelling and sizing degree had little influence on the diffusivity of paper; 3 Linear relationship existed between sheet density and diffusivity, and, 4. Highly sfgnificant linear relationship could be observed between diffusivity and Darcy s gas permeability. Results indicate that diffusivity, an intrinsic property of paper, can provide a valuable information for precise evaluation and improved quality control of water-vapor proof properties of paper.

• Proceedings of the KIEE Conference
• /
• 1994.07a
• /
• pp.223-225
• /
• 1994

In these days, it is widely applications of Linear Induction Motor(LIM) that used propulsion system of maglev and LIM Car. elevator. conveyor system, servo system, etc. The calibration method for, performance of LIM is more difficult than static state of one. Then we made testing system to measurement for dynamic performance of LIM and deal with data acquisition board on PC system. We try to get for the data measuring that is thrust force, braking force versus speed(r.p.m. or time) and current, voltage, frequency versus speed.

• Publications of The Korean Astronomical Society
• /
• v.30 no.2
• /
• pp.593-594
• /
• 2015

We present our analysis results for an updated orbital ephemeris for the dipping low mass X-ray binary 4U 1624-49, using the light curve collected by the All Sky Monitor (ASM) on board the Rossi X-ray Timing Explorer (RXTE) and the Monitor of All-Sky X-ray Image (MAXI). To make clear dip profiles, the light curve from the ASM and the MAXI were divided into ten 500d segments and four 400d segments for ASM and MAXI light curves, respectively, and folded with the linear ephemeris proposed by Smale et al. (2001). The phases of dip centers were determined by the method adopted from Hu et al. (2008). The phase drift was then fitted with a linear function. We obtained an updated orbital period of 0.869896(1) d and a phase zero epoch of JD 2450088.6618(57). No clear orbital period derivative is detected with a 2-sigma upper limit of $1.4{\times}10^{-6}(yr)^{-1}$ from a quadratic curve fitting of the dip phase evolution.

• Journal of agricultural medicine and community health
• /
• v.26 no.2
• /
• pp.97-109
• /
• 2001

To investigate the total cholesterol level and its related factors in the rural and sea-board, 2,840 adults who participated voluntarily were examined during the study period December 1999 to February 2000. The height, weight, and fasting serum total cholesterol were measured. Body mass index was calculated. Information on age, gender, smoking, alcohol, and menopausal status in women were collected using a questionnaire by interviewing method. The mean value of total cholesterol was 191.6mg/ dl in sea- board and 173.6mg/ dl in rural men, respectively, and 206.9mg/ dl and 186.9mg/ dl in sea-board and in rural women. By simple analysis, in men, area, BMI and smoking were significant risk factors(p<0.01). Area(p<0.01), age(p<0.01), BMI(p<0.01), smoking(p<0.05), and menopausal status (p<0.01) were significant. In multiple linear regression analysis, the significant factors for total cholesterol in men were area(sea-board versus rural area; p<0.01), body mass index(the more obese; p<0.01), and smoking (non-smoker versus smoker ; p<0.05). Those in women were area(sea-board versus rural area; p<0.01), body mass index(the more obese; p<0.01), and menopausal status(menopause versus normal; p<0.01). Thus, in both gender, the significant factors related with total cholesterol were area and body mass index, and in addition to those, menopausal status was proved as a significant risk factor in women.

• Korean Journal of Remote Sensing
• /
• v.13 no.2
• /
• pp.85-98
• /
• 1997

A geometric model of pushbroom-type linear CCD camera images is proposed in this paper. At present, this type of cameras are used for obtaining almost all kinds of high-resolution optical images from satellites. The proposed geometric model includes not only a forward transformation which is much more efficient. An inverse transformation function cannot be derived analytically in a closed form because the focal point of an image varies with time. In this paper, therefore, an iterative algorithm in which a focal point os converged to a given pixel position is proposed. Although the proposed model can be applied to any pushbroom-type linear CCD camera images, the geometric model of the high-resolution multi-spectral camera on-board KITSAT-3 is used in this paper as an example. The flight model of KITSAT-3 is in development currently and it is due to be launched late 1998.

• Smart Structures and Systems
• /
• v.8 no.4
• /
• pp.367-384
• /
• 2011

This paper presents the design and experimental evaluation of fast output sampling feedback controller to minimize structural vibration of a cantilever beam using Shape Memory Alloy (SMA) wires as control actuators and piezoceramics as sensor and disturbance actuator. Linear dynamic models of the smart cantilever beam are obtained using online recursive least square parameter estimation. A digital control system that consists of $Simulink^{TM}$ modeling software and dSPACE DS1104 controller board is used for identification and control. The effectiveness of the controller is shown through simulation and experimentation by exciting the structure at resonance.

• Proceedings of the Korean Institute of Intelligent Systems Conference
• /
• 1998.06a
• /
• pp.199-202
• /
• 1998

This paper describe an intelligent cruise control system for automobile. With the remarkable numerical increase of automobiles on the road, the optimized traffic flow control using the cruise control is one of the very important traffic problems to overcome the limitation of an existing road capacity. Based on this idea that minimize the fuel cost and the air pollution, and accept a driver's needs for driving, we have developed an intelligent cruise control system for vehicle. This proposed intelligent fuzzy cruise controller was successfully implemented using the fuzzy algorithm, the i80c196 μ-controller board and the throttle valve actuator. The field test results on an linear road was introduced.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.2
• /
• pp.267-274
• /
• 2002

Using a flexible rotating beam test bed, experimental verification of a flexible multibody dynamic simulations for a rotating beam model has been carried out. The test bed consists of a flexible arm, harmonic driver reducer, AC servo motor and DSP board with PC. The mechanical ports of the test bed has been designed using 3D CAD program. For the simulation model, mass and moment of inertia of each part of the flexible rotating beam test bed are also obtained from 3D CAD model. In the flexible multibody dynamic simulations, the substructuring model has been established to capture nonlinear effects of the flexible rotating beam. Through the experimental verification, substructuring model provides better results than those from the linear model in the high speed rotation.

• Proceedings of the KIPE Conference
• /
• 2000.07a
• /
• pp.620-623
• /
• 2000

A very simple control approach using neural network for the robust position control of a Permanent Magnet Synchronous Motor(PMSM) is presented The linear quadratic controller plus feedforward neural network is employed to obtain the robust PMSM system approximately linearized using field-orientation method for an AC servo. The neural network is trained in on-line phases and this neural network is composed by a fedforward recall and error back-propagation training. Since the total number of nodes are only eight this system can be easily realized by the general microprocessor. During the normal operation the input-output response is sampled and the weighting value is trained multi-times by error back-propagation method at each sample period to accommodate the possible variations in the parameters or load torque. And the state space analysis is performed to obtain the state feedback gains systematically. IN addition the robustness is also obtained without affecting overall system response. This method is realized by a floating-point Digital Singal Processor DS1102 Board (TMS320C31) The basic DSP software is used to write C program which is compiled by using ANSI-C style function prototypes.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.2 s.95
• /
• pp.164-175
• /
• 1999

If the camera plane is nearly parallel to the calibration board on which objects are defined, most of existing calibration approaches such as Tsai's radial-alignment-constraint method cannot be applied. Recently, for such an ill-conditioned case, Zhuang & Wu suggested the linear two-stage calibration algorithm assuming that the exact values of focal length and scale factor are known a priori. In this paper, we developed an iterative two-stage algorithm starts with initial guess fo the two parameters to determine the value of the others using Zhuang & Wu's method. In the second stage, the two parameters are locally optimized. This process is repeated until any improvement cannot be expected any more. The performance comparison between Zhuang & Wu's method and our algorithm shows the superiority of ours. Also included are the computational results for the effects of the distribution and the number of calibration points on the calibration performance.