• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.10
• /
• pp.954-960
• /
• 2008

The effects of elastic modulus coefficient and linear expansion coefficient of overhead distribution power line(ACSR $58 mm^2$) on sag behavior in distribution line have been investigated to clarify the difference between specification and experimental level. The elastic modulus coefficients of Al wire and steel wire were $5,182.6 kgf/mm^2,\;18,348.8 kgf/mm^2$, respectively Therefore, the computational composition elastic modulus coefficient of the power line was $7,063.5 kgf/mm^2$, while that of experimentally measured was $7681.1 kgf/mm^2$. As a result, we found that elastic modulus coefficient which was experimentally measured was higher than that of computational by 8.7 %. However, when planner designs the sag of disoibution line, the elastic modulus coefficient of power line $8,400 kgf/mm^2$ should be generally adopted. These two different using values lead to the sag difference of 0.62 m. The other results will be discussed.

• The Bulletin of The Korean Astronomical Society
• /
• v.46 no.1
• /
• pp.38.3-38.3
• /
• 2021

We are developing an optomechanical design of infrared telescope for the CubeSat and Unmanned Aerial Vehicle (UAV) which adapts the Linear Astigmatism Free- Three Mirror System in the confocal off-axis condition. The small entrance pupil (diameter of 40 mm) and the fast telescope (f-number of 1.9) can survey large areas. The telescope structure consists of three mirror modules and a sensor module, which are assembled on the base frame. The mirror structure has duplex layers to minimize a surface deformation and physical size of a mirror mount. All the optomechanical parts and three freeform mirrors are made from the same material, i.e., aluminum 6061-T6. The Coefficient of Thermal Expansion matching single material structure makes the imaging performance to be independent of the thermal expansion. We investigated structural characteristics against external loads through Finite Element Analysis. We confirmed the mirror surface distortion by the gravity and screw tightening, and the overall contraction/expansion following the external temperature environment change (from -30℃ to +30℃).

• Proceedings of the Korea Concrete Institute Conference
• /
• 1995.04a
• /
• pp.268-273
• /
• 1995

In recent years, precast prestressed concrete segmental box girder bridges have been increasingly constructed Expansion disphragm segment of this type bridge transfers forces from the superstructure onto bearing or column, and plays an important roll of anchorage zone for longitudinal prestressed forces. Non-linear stresses occur inside of diaphragms by these extensive concentrated forces. In this study, the strut-and-tie models are proposed to design an expansion segment rationally. A formula to determine the effective transverse prestressed forces is proposed on the basis of these models. The present study is expected to provide an effective tool to design expansion segment of prestressed concrete bridges rationally.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1346-1348
• /
• 2001

Generally, Invar alloy shows very low thermal expansion characteristics, lower than $2{\times}10^{-6}$/K approximately. To apply Fe-Ni-Co-C Invar alloy as a core material for large ampacity transmission line we studied the effects of magnetic properties on coefficient of thermal expansion. The coefficient of thermal expansion(CTE) suddenly decreases with addition of a little carbon(0.08%), increases with the increasing carbon and has a constant value at the composition over than 1.0%C. The trend of Curie temperature change with carbon is similar with that of CTE. Therefore, the CTE has a linear relationship with Curie temperature. However, the CTE linearly decreases with the ratio of saturation magnetization and Curie temperature(${\sigma}_s/T_c$).

• Bulletin of the Korean Chemical Society
• /
• v.22 no.11
• /
• pp.1255-1260
• /
• 2001

The expansion of two different kinds of hydrodynamic size of polymethyl methacrylate (PMMA Mw: 1.56- 2.04 ${\times}$ 106 g/mol) has been measured by dynamic light scattering and viscometry above the Flory $\theta$ temperature of the variou s solvents such as n-butyl chloride, 3-heptanone, and 4-heptanone. The expansion of PMMA chains was analyzed in terms of universal temperature parameters and also compared with previous results of polystyrene (PS) system. First it was found that simple $\tau/{\tau}c$ parameter no longer had its universality for the expansion behavior of hydrodynamic size in the chemically different linear polymer chains. However after modifying ${\tau}/{\tau}c$ parameter into $(Mw/Ro2)3}2(\tau/\tauc)$, we observed a much better universality for both PMMA and PS systems. Here Mw, Ro, $\tau[=(T-{\theta}$)/${\theta}$]$, and ${\tau}c[=({\theta}-Tc)/Tc]$ are defined as the weight average molecular weight, the unperturbed end-to-end distance, the reduced temperature and the reduced critical temperature, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.34 no.5
• /
• pp.52-58
• /
• 2006

Coffee chaff for manufacturing of the 6 mm thick cement-bonded boards was obtained from a coffee processing industry at Omuo-Ekiti, in Ekiti State, Nigeria. Boards were produced with three levels of cement to coffee chaff ratio of 1.5:1, 2.5:1 and 3.5:1; and at three levels of mixing curing reagent of 2.0%, 2.5% and 3.0%. Three dimensional properties of thickness swelling (TS), water absorption (WA) and linear expansion (LE) were investigated after 48 hours immersion in water. The mean values obtained for TS, WA and LE ranged from 0.46% to 1.47%, from 11.52% to 24.00%, from 0.19% to 0.35%, respectively. The most dimensionally stable boards were produced at the highest mixing levels of curing reagent and cement to coffee chaff ratio of 3.0% and 3.5:1, respectively. The coffee chaff is suitable as raw material for the manufacture of cement-bonded composites and it would be able to stimulate and activate the use of other agro-byproducts for the manufacture of value-added panels.

• International Journal of Ocean Engineering and Technology Speciallssue:Selected Papers
• /
• v.6 no.1
• /
• pp.7-14
• /
• 2003

The interaction of monochromatic incident waves with a submerged horizontal porous membrane is investigated in the context of two-dimensional linear hydro-elastic theory. It is assumed that the membrane is made of material with very fine pores so that the normal velocity of the fluid passing through the porous membrane is linearly proportional to the pressure difference between two sides of the membrane (e.g. Darcy's law). Using the Eigen-function expansion method, the wave-blocking performance of a submerged horizontal porous membrane is tested with various membrane tensions, porosities, lengths, and submerged depths. It is found that an optimal combination of design parameters exists for given water depth and wave characteristics.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.263-268
• /
• 1997

Development of a high speed feed drive system has been a major issue for the past few decades in machine tool industries. The reduction of tool change time as well as repid travel time can enhance the productivity. However,the high speed feed drive system generates more heat in nature,which leads to thermal expansion that has adverse effects on the accuracy of machined part. The paper divides the feed drive system into the ball screw and guide way. For each part, the thermal behvior model is separtately developed to estimate the position error of the respective feed drive system that is caused by the thermal expansion. The modified lumped capacitance method is used to analyze the linear position error of the ball screw. The thermal deformation of guide way parts affects the straightness and angular error as well as linear position error. Finite element method is used to estimate the thermal behavior of these guide way parts. The effectiveness of the proposed models are verified through the experiments using laser interferometer.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 1999.03b
• /
• pp.136-142
• /
• 1999

The injection molded part shrinks in the process of solidification by the amount of the coefficient of linear thermal expansion multiplied by the temperature difference between the coefficient of linear thermal expansion multiplied by the temperature difference between the room temperature and the temperature at which the solid structure is formed in the mold And it is called warpage for this type of deformation that shrinkage are not uniform throughout the injection molded part. To predict warpage phenomena in the articles the results obtained theoretically from the change of mold temperature fiber content of composites have been compared with exsperimental results.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2001.03a
• /
• pp.153-160
• /
• 2001

피에조콘관입시험(PCPT)의 소산시험은 in-situ 상태의 압밀계수(c/sub v/)를 추정하는 방법으로 널리 이용되어왔다. 본 연구에서는 spherical cavity expansion theory 및 axisymmetric uncoupled linear consolidation equation(Gupta & Davidson, 1986)을 이용하여 과압밀점토에서의 초기과잉간극수압의 분포 및 과잉간극수압의 시간에 대한 소산현상을 해석하는 수치해석방법을 제안하여 현장시험결과 및 실내시험결과와 비교 분석하였다. ADIS (alternating direction implicit scheme)를 이용한 FDM 해석을 실시한 결과와 현장시험의 소산곡선은 잘 부합되는 것으로 나타났으며 압밀계수도 실내실험 또는 피에조콘관입 시험에 대한 추정방법으로 산출된 값과 비교적 일치하는 것으로 나타났다.