• 한국산학기술학회논문지
• /
• 제12권9호
• /
• pp.4008-4014
• /
• 2011

이 연구는 뇌졸중 환자를 대상으로 임상척도를 이용하여 엉덩관절의 근력, 감각과 경직이 균형능력에 미치는 영향을 알아보기 위해 실시되었다. 32명의 뇌졸중 환자를 대상으로 도수근력검사를 사용하여 환측 다리의 가벼운 접촉감각과 엉덩관절굽힘근, 폄근, 모음근, 그리고 벌림근의 근력을 측정하였고, 수정 Ashworth 척도를 이용하여 넙다리근의 경직을 측정하였으며, 기능적 균형 척도를 이용하여 정적 및 동적균형능력을 측정하였다. 수집된 자료는 다중회귀분석을 이용하여 분석하였다. 연구결과 정적균형에 유의한 영향을 미치는 요인은 엉덩관절벌림근력, 넙다리 경직, 가벼운 접촉감각인 것으로 나타났으며(p<0.05), 설명력은 80.5%인 것으로 나타났다. 동적균형능력에 영향을 미치는 요인으로는 엉덩관절벌림근력과 가벼운 접촉감각인 것으로 나타났으며(p<0.05), 설명력은 77.9%인 것으로 나타났다. 엉덩관절벌림근력과 가벼운 접촉감각은 정적균형과 동적균형 모두에 영향을 미치는 것으로 나타나, 앞으로 균형에 대한 검사와 중재 프로그램 제공 시 엉덩관절벌림근력과 가벼운 접촉감각 요인을 고려하는 것이 필요할 것으로 여겨진다.

• 대한치과교정학회지
• /
• 제28권5호
• /
• pp.689-698
• /
• 1998

법랑질의 표면처리에 따른 광중합형 글래스아이오노머 시멘트의 전단결합강도를 알아보고자 사람 소구치 80개를 선택하여 8개군으로 나누어 전단 결합 강도를 측정하고, 접착 파절의 양상을 평가하여 다음과 같은 결과를 얻었다. $1.37\%$ 인산용액으로 부식한 후 건조상태에서 글래스아이오노머 시멘트, 광중합형 레진, 화학중합형 레진으로 각각 부착한 실험군에서 글래스아이오노머 시멘트 실험군의 전단결합강도는 두 군과 유의한 차가 없었으나 화학중합형 레진군의 그것은 광중합형 레진군에 비해 유의성있게 낮았다 (p<0.05). $2.37\%$ 인산 실험군, $10\%$ 폴리 아크릴산 실험군, $1.23\%$ APF 실험군, 산처리하지 않은 실험군의 습한 상태에서 부착한 글래스아이오노머 시멘트의 전단결합강도에서 산처리하지않은 실험군의 그것이 유의성 있게 낮았으며, 그 외 군간에는 유의성 있는 차이가 없었다 (p<0.05). 3. 글래스아이오노머 실험군에서 습기의 존재가 전단결합강도에 유의성 있는 영향을 미치지 않았다 (p<0.05). 4. 산부식처리를 하지않은 군의 접착제 잔류지수가 가장 낮았으며 $37\%$인산용액으로 처리한 군의 접착제 잔류지수가 가장 높았다.

• Restorative Dentistry and Endodontics
• /
• 제17권2호
• /
• pp.307-330
• /
• 1992

The aim of this study was to investigate the physical properties of visible light curing Glass Ionomer cement for restorative esthetic filling. The control group was the autopolymerizing GC Fuji II Glass Ionomer cement (2.2: 1 P/L ratio) and the experimental groups were made by following procedure. To induce the polymerization by visible light, the powder of GC Fuji II GI cement and the liquid of Vitrabond for base & liner were mixed in an amalgam capsule with 2.5:1, 3.0:1, 3.5:1 P/L ratio (% wt/wt). After fabrication of specimens, compressive strength, fracture toughness ($K_{IC}$) Scanning Electron Microscope and X-ray Diffraction, water-leachable content, marginal leakage and surface roughness were studied. The results were as follows: 1. Only experimental No. 1 group (visible light curing) showed less compressive strength than control group 1 hour after curing. Strength was increased with aging in all groups, so the compressive strength of light curing groups was no less than that of autopolymerizing group after 3 weeks. 2. Experimental No.3 group (visible light curing) was inferior to No.2 group (visible light curing) in fracture resistance but light curing groups were more resistant to fracture than autopolymerizing group and showed ductile fracture pattern as compared with the brittle fracture pattern of autopolymerizing group. 3. From scanning electron microscopic image, various sized unreacted powder particles, surrounded by silica gel, were embedded in polysalt matrix. Light curing groups showed little crack and more dense unreacted particles than autopolymerizing group. 4. From X-ray diffraction analysis, GC Fuji II Glass Ionomer cement powder and all groups showed glassy appearance but light curing groups seemed to be more intensive in crystaline than autopolymerizing group. S. The most significant dissolution was shown in early setting period in all group. Light curing groups were dissolved less than autopolymerizing group. 6. Marginal leakage was not different significantly in case of cavity margin composed of same tooth structure (ex. only enamel margin, only dentin margin) but much more leakage was shown in dentin/cementum margin than enamel margin. In only case of only enamel margin, light curing groups were superior to autopolymerizing group. 7. All groups showed relatively smooth surface, which irregularity was less than $1{\mu}m$. Light curing groups were smoother than autopolymerizing group.

• 한국강구조학회 논문집
• /
• 제21권2호
• /
• pp.127-134
• /
• 2009

본 연구의 목적은 경량콘크리트에 매립된 쉬어 커넥터의 전단거동 특성을 파악하는데 있다. 본 연구는 기존 실험결과와 유한요소해석에 의한 해석결과를 비교분석하여 유한요소 해석의 타당성을 확인하고 경량콘크리트의 압축강도($f_{ck}$) 변화에 따른 쉬어 커넥터의 전단강도를 기존 설계식(AISC-LRFD 및 Eurocode 4)과 비교분석하였다. 유한요소해석 결과 경량콘크리트에 매립된 쉬어 커넥터의 전단강도는 Eurocode 4의 쉬어 커넥터의 전단강도와 거의 일치하는 것으로 나타났다.

• 열처리공학회지
• /
• 제18권1호
• /
• pp.12-17
• /
• 2005

Effects of Zn and Zr additions on the microstructure and mechanical properties of Al-5%Mg-1%Mn alloys were investigated. As Zn content increased in the Al-Mg-Mn-Zn alloys, the tensile strength and ductility of as-cast alloys rather decreased while the tensile strength of the heat-treated alloys significantly increased mainly due to the precipitation of fine $MgZn_2$ phases. Small amount of Zr was added to the 3%Zn alloy to further enhance the mechanical properties, and it appeared to increase the strength and ductility, especially in as-cast state.

• 열처리공학회지
• /
• 제17권5호
• /
• pp.299-304
• /
• 2004

Influence of Ca addition on microstructure and room temperature mechanical properties has been studied for AZ31(Mg-3%Al-1%Zn-0.2%Mn)-(0~0.5)%Ca wrought alloys, based on experimental results from metallography, X-ray diffractometry and mechanical tests. Yield strength, ultimate tensile strength and hardness of the alloys increased remarkably with increasing Ca content, whereas elongation was deteriorated continuously. Microstructural examination revealed that Ca addition efficiently refined grains of ${\alpha}$(Mg) phase and that some of the Ca dissolved in ${\beta}(Mg_{17}Al_{12})$ precipitates. The former and the latter facts are thought to be responsible for improved strength and loss of ductility of the AZ31+Ca wrought alloys, respectively.

• 한국물환경학회지
• /
• 제21권1호
• /
• pp.66-72
• /
• 2005

Effect of the pH, molar ratio of Cu(II)/EDTA, concentration of Cu(II)-EDTA and ionic strength on the photocatalytic oxidation(PCO) of Cu(II)-EDTA in solar light was studied in this work. Experimental results in this work were compared with previous results obtained with UV-lamp. In the kinetics, Cu(II)-EDTA decomposition was favorable below neutral pH. The removal of Cu(II) and DOC was favorable as $TiO_2$ dosage increased. The initial rate for the decomplexation of Cu(II)-EDTA linearly increased as the concentration of Cu(II)-EDTA increased. The removal of Cu(II) and DOC was not much affected by variation of ionic strength with $NaClO_4$ as a background ion while much reduction was observed in the presence of background ions having higher formal charges. The removal trend of Cu(II) and DOC with variation of ionic strength and concentration of Cu(II)-EDTA in solar light was similar with that in UV light. Variation of the molar ratio of Cu(II)/EDTA showed a negligible effect on the removal of both Cu(II) and DOC. However, removal of both Cu(II) and DOC was two-times greater than that previous results obtained with UV light.

• 대한치과기공학회지
• /
• 제42권4호
• /
• pp.341-347
• /
• 2020

Purpose: This study aimed to evaluate the effect of post-curing method on the flexural strength of provisional restorative resins produced by a digital light processing printer. Methods: A total of 20 specimens were produced, with a length of 64 mm, width of 10 mm, and thickness of 3.3 mm using a digital light processing printer. Two types of provisional restorative resins made with different post-curing methods were investigated and divided into conventional and vacuum groups. For the flexural strength test, each group was prepared by each method according to ISO 10477, and the flexural strength was measured with a universal testing machine. For statistical analysis, data were analyzed by independent t-test and Mann-Whitney U test. Results: The flexural strengths of the conventional and vacuum groups were 151.89 MPa and 131.94 MPa, respectively, showing a statistically significant difference (p<0.05). Conclusion: Within the limitation of this study, provisional restorative resins produced with vacuum demonstrated lower flexural strength than those produced with conventional postcuring method.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 봄 학술발표회 논문집
• /
• pp.131-136
• /
• 2002

In recent year, it has been investigated on the reduction of mass of structures for the purpose of the larger space and the economy with the industry developing very fast and qualitatively. So the purpose of this study is to investigate the manufacture of light weight concrete panel using the artificial light-weight aggregate as a part of the substitution of foamed styrene and polyurethane because of narrow allocable temperature zone in use. The compressive strength, flexural strength, unit weight, absorption test and thermal conductivity were practised at 3, 7 and 28 days after manufacturing the light-weight concrete lot the panel core: the filling ratio of continuous void was defied as 40%, 50%, and 60% and water-cement rate was 35, 40 and 45%. As a result of this, it was revealed that the mixture derived from filling ration of void of 50% and water-cement ratio 40% were developing the best properties of the others.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2003년도 봄 학술발표회 논문집
• /
• pp.7-12
• /
• 2003

In scrapped material field, about ten millions ton of waste plastic materials are produced in korea. However recycling rate of waste plastic materials have above 25%. Therefore, it is urgently needed that they are used as recycled materials in order to prevent environment pollution and grain economic profits. In this paper, physical and mechanical properties of light weight concrete using waste plastic materials for aggregates are described in order to develop a light weight concrete with the aggregate made from waste plastic goods, it was carried out many experiments on mix proportion and strength. According to the experimental results, high-strength mortar was necessary to make light weight concrete using aggregate of waste plastic materials. Especially, considering the side of recycling of plastic wastes, it is recommended that recycled aggregates made from waste plastic materials is applied to light weight concrete.