• Journal of the Korea Institute of Military Science and Technology
• /
• v.12 no.1
• /
• pp.123-132
• /
• 2009

Civil petitions and law suits against the military rifle shooting noise have been increased because many military shooting ranges are located near civilian residential area. In order to solve the noise problems, military have devised various methods. In this study, propagation properties of rifle shot through atmosphere were investigated. The military rifle shooting noise level at 5m from muzzle was between $l14{\sim}120dB$ in all directions. The noise level loom both backward and sideward away from system firing range consisting lines of 8 shooting locations were 90dB, when shots were all fired within 10 seconds. At present some of military bases established sound barriers, muzzle enclosures, silencers, and indoor shooting ranges to reduce noises and these prevention methods can reduce noise by $5{\sim}20dB,\;5{\sim}9dB,\;5{\sim}13dB,\;40{\sim}50dB$, respectively. Even though indoor shooting range has the best performance, it requires very expensive construction cost and has short length between target and shooter. In comparison, muzzle enclosure is cheap, but because it is installed in fixed position it can only be used in one shooting position. Therefore a commander should select appropriate methods to reduce military rifle shooting noise considering distance from residential area to the range, mission of military training, budget, etc.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.1A
• /
• pp.80-86
• /
• 2010

This work has been measured and analyzed the device degradation of NBTI (Negative Bias Temperature Instability) stress induced the increase of gate-induced-drain-leakage(GIDL) current for p-MOS transistors of gate channel length 0.13 [${\mu}m$]. From the relation between the variation of threshold voltage and subthreshold slop by NBTI stress, it has been found that the dominant mechanism for device degradation is the interface state generation. From the GIDL measurement results, we confined that the EHP generation in interface state due to NBTI stress led to the increase of GIDL current. As a results, one should take care of the increased GIDL current after NBTI stress in the ultra-thin gate oxide device. Also, the simultaneous consideration of reliability characteristics and dc device performance is highly necessary in the stress parameters of nanoscale CMOS communication circuit design.

• Smart Structures and Systems
• /
• v.22 no.4
• /
• pp.481-493
• /
• 2018

Ultrasonic guided waves have attracted increasing attention for non-destructive testing (NDT) and structural health monitoring (SHM) of bridge cables. They offer advantages like single measurement, wide coverage of acoustical field, and long-range propagation capability. To design defect detection systems, it is essential to understand how guided waves propagate in cables and how to select the optimal excitation frequency and mode. However, certain cable characteristics such as multiple wires, anchorage, and polyethylene (PE) sheath increase the complexity in analyzing the guided wave propagation. In this study, guided wave modes for multi-wire bridge cables are identified by using a semi-analytical finite element (SAFE) technique to obtain relevant dispersion curves. Numerical results indicated that the number of guided wave modes increases, the length of the flat region with a low frequency of L(0,1) mode becomes shorter, and the cutoff frequency for high order longitudinal wave modes becomes lower, as the number of steel wires in a cable increases. These findings were used in design of transducers for defect detection and selection of the optimal wave mode and frequency for subsequent experiments. A magnetostrictive transducer system was used to excite and detect the guided waves. The applicability of the proposed approach for detecting and locating wire breakages was demonstrated for a cable with 37 wires. The present ultrasonic guided wave method has been found to be very responsive to the number of brokenwires and is thus capable of detecting defects with varying sizes.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.16 no.6
• /
• pp.112-123
• /
• 2017

The accurate forecasting of the public transportation's transit and arrival time has become increasingly important as more people use buses and subways instead of personal vehicles under the government's public transportation promotion policy. Using bus management system (BMS) data, which provide information on the real-time bus location, operation interval, and operation history, it is now possible to analyze the bus schedule reliability. However, the punctuality should always be considered together with the operation safety. Therefore, this study suggests a new methodology to secure both reliability and safety using the BMS data. Unlike other studies, we calculated the bus travel time between two bus stops by dividing the total travel length into 6 sections using 5 different measuring points. In addition, the optimal travel time for each bus route was proposed by analyzing the mean, standard deviation and coefficient of variation of the each section's measurement. This will ensure the reliability, safety and mobility of the bus operation.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.41 no.3
• /
• pp.39-44
• /
• 2004

Fiber Bragg grating sensors are fabricated by core index modulation using UV laser and phasemask. Bragg wavelength of the grating is changed by the external strain. In this paper, a signal processing system of fiber Bragg grating sensor has studied in the optical wavelength domain. The system is based on the sweep semiconductor light source that consists of SLD, F-P tunable filter and etalon filter. The hysteresis effects of PZT in the F-P tunable filter are compensated. The long term measurement stability is obtained by controlling the temperature of F-P tunable filter and the SLD. We compare the strain data from fiber Bragg grating sensor and that from strain gauge at concrete hume pipe. We also get very good results for the long gauge displacement using fiber Bragg grating sensor which are identical to the data with short gauge length ordinary displacement sensor.

• The Research Journal of the Costume Culture
• /
• v.6 no.3
• /
• pp.201-216
• /
• 1998

This study is aimed at exploring a reasonable and reliable method of measuring pre-school children's somatotypes and there by, data basing the information obtained and classifying their somatotypes, at providing useful data which can be utilized for the design of their dress forms and enhancing the fitness of their apparels. to this end, 330 pre-school children living in the capital area and aged fro m4 to 6 were sampled to be subject to the measurement of their somatotypes. The results of this study can be summarized as follows; 1. As the pre-school children grow, the scales indicating their vertical growth including height could well be measured differently, but those scales indicating their lateral somatotypes which reflect their postural changes did not show among age groups. in other words, male kids were higher in the scales including height than female kids, while there were not differences between sexes in most scales indicating their lateral somatotypes. 2. The elements comprising the somatotypes were the size of body skeleton, the thickness of body mass, the posture and shape of body mass, the lateral under-neck shape, the extrusion of belly, the length between front and the back shoulder, the shape of lower belly, the shape of upper hip, the shape of lower hip and the slope of shoulders. Among them, the first two elements accounted for 64.8% of the total distribution, which means that these two elements explain the body-mass somatotypes of kid's most effectively. 3. The sample kids were divided into two types for classification of their somatotypes. As a result, it was found that the elements determining their somatotypes most influentially are, unlike adults' case the size of body skeleton rather than posture or lateral body shape. The type I showed less dimensions in most scales than type II, while their shoulder were les developed,. The type I was found distributed much in 4-year-old female kids. The type II showing more development in each element was found distributed much in 6-year-old male kids.

• Journal of the Korean Chemical Society
• /
• v.32 no.3
• /
• pp.227-232
• /
• 1988

A kinetic study was made to determine the mechanism of the aquation of $cis-[Co(en)_2(NH_3)Cl]^{2+}\;in\;Hg^{2+}$ aqueous solution. The progress of reaction was followed UV/vis-spectrophotometrically by a measurement of the absorbance at a specific wave length (530nm) of $cis-[Co(en)_2(NH_3)Cl]^{2+}$ as a function of time. The experimental results have shown that the reaction rate is dependent upon the concentration of $Hg^{2+}$ that act as a catalyst. And it was found that the overall reaction proceed with second order, first order with respect to Co(III) complex and $Hg^{2+}$. Activation parameters, ${\Delta}H^{\neq}\;and\;{\Delta}S^{\neq}$, were obtained as 12.9 kcal/mol and -19.3 e.u., respectively. We have proposed a plausible reaction mechanism which is consistent with the observed rate equation.

• Journal of Korea Water Resources Association
• /
• v.40 no.11
• /
• pp.841-849
• /
• 2007

This study evaluated the effect of combined rainfall observation of using rain gauge and rain radar. The effect of combined observations is to be evaluated by considering the decrease of measurement error due to combined use of design orthogonal observation methods. As an example, this study evaluated the rain gauge network of the Keum river basin, and showed how the density of rain gauges could be decreased by combining the radar observation. This study applied the researches on sampling error by North and Nakamoto(1989), Yoo et al. (1996) and Yoo (1997), also the simple NFD model for representing the rainfall field. The model parameters were decided using the rainfall characteristics (correlation time and length) estimated using the data collected in the Keum River Basin by 28 rain gauges and the operation rule of radar was assumed arbitrarily. This study considered the rain gauge density criteria provided by WMO(1994) and the rain gauge density installed in the Keum river basin to decrease the rain gauge density under the condition of introducing the radar.

• Korean Journal of Materials Research
• /
• v.26 no.3
• /
• pp.154-159
• /
• 2016

A roll-bonding process was applied to fabricate an AA1050/AZ91/AA1050 laminate complex sheet. Two AA1050 and one AZ91 magnesium sheets of 2 mm thickness, 30 mm width and 200 mm length were stacked up after surface treatment that included degreasing and wire brushing; material was then reduced to a thickness of 3 mm by one-pass cold rolling. The laminate sheet bonded by the rolling was further reduced to 2 mm in thickness by conventional rolling. The rolling was performed at 623K without lubricant using a 2-high mill with a roll diameter of 210 mm. The rolling speed was 15.9 m/min. The AA1050/AZ91/AA1050 laminate complex sheet fabricated by roll bonding was then annealed at 373~573K for 0.5h. The microstructure of the complex sheets was revealed by electron back scatter diffraction (EBSD) measurement; the mechanical properties were investigated by tensile testing and hardness testing. The strength of the complex sheet was found to increase by 11 % and the tensile elongation decreased by 7%, compared to those values of the starting material. In addition, the hardness of the AZ91 Mg region was slightly higher than those of the AA1050 regions. Both AA1050 and AZ91 showed a typical deformation structure in which the grains were elongated in the rolling direction; however, the mis-orientation distribution of grain boundaries varied greatly between the two materials.

• Journal of the Korean Geotechnical Society
• /
• v.32 no.5
• /
• pp.27-36
• /
• 2016

This paper presents the investigation of the major influence factors on the degree of soil plugging for open-ended piles based on the Coupled Eulerian-Lagrangian (CEL) numerical technique. The main objective of this study was to investigate the effect of soil plugging on the response of piles in various conditions. Through comparison of the results of field load tests, the CEL methodology was found to be in good agreement with the general trend observed by in situ measurement. Additionally, the parametric studies were performed by controlling the soil conditions, soil elastic moduli, end-bearing conditions and multi layers. It was found that the degree of soil plugging for sand layers was greater than that of clay layers. Also, the degree of soil plugging increased with an increase in both the soil stiffness and length of pile embedded in the bearing layer.