• 한국해양학회지
• /
• v.16 no.1
• /
• pp.31-37
• /
• 1981

Saline water movements in relation to tidal condition and river discharge in the estuary of the Nakdong River are discussed on the basis of the observation data. The difference of salinity between the surface and the bottom layer was 1∼3 at spring tide forming a vertically homogeneous estuary, while at neap tide, it ranges up to 7∼15 indicating a sharp salt wedge. The maximum salinity appeared approximately at an hour after the high water, that is, three hours after the landward velocity maximum, while the salinity maximum at around an hour after the low water, that is, three hours after the seaward velocity maximum. The density current speed at a section located 10km landward from the river mouth was observed approximately to be 45cm sec$\^$-1/ at 8m layer.The relations between the salinity at Gupo and the river discharge at Jindong are estimated by means of the least square method. The maximum length of the salt wedge is calculated approximately to be 22km at neap tide and 16km at spring tide, which is in accordance with the observed data. The salinity influence area is deduced to be 45km at spring tide and 35km at neap tide. The diffusion coefficient of salinity was estimated approximately to be 1.5 10$\^$8/$\textrm{cm}^2$ sec$\^$-1/ at Samrak and 8 10$\^$5/$\textrm{cm}^2$ sec$\^$-1/ at Gupo at neap tide, while it was 1.4 10$\^$7/$\textrm{cm}^2$ sec$\^$-1/ at Dongwon at spring tide.

• Journal of Korean Tunnelling and Underground Space Association
• /
• v.7 no.4
• /
• pp.285-294
• /
• 2005

The behaviors of the ground in crossed zone and the existing upper tunnel in shallow cover due to the excavation of new lower tunnel crossed to that was studied. Model test was performed in the large scale test pit, the size was '$4.0m(width){\times}3.8m(height){\times}4.1m(length)$'. Test ground was constructed uniformly by sand in middle density and test with the crossed angle of $56^{\circ}$ (obliquely) were performed. The numerical analysis was performed on equal condition with model test. Results of the study by model test and numerical analysis show that earth pressure and settlement of the ground in crossed zone were redistributed due to the longitudinal arching effect by the excavation of lower tunnel. Model test shows that upper tunnel blocks stress flow due to the longitudinal arching effect by excavation of lower tunnel.

• Proceedings of the KSR Conference
• /
• 2009.05a
• /
• pp.1003-1009
• /
• 2009

The Spatial Image contents of Geomorphology 3-D environment is focused by the requirement and importance in the fields such as, national land development plan, telecommunication facility management, railway construction, general construction engineering, Ubiquitous city development, safety and disaster prevention engineering. The currently used DEM system using contour lines, which embodies geographic information based on the 2-D digital maps and facility information has limitation in implementation in reproducing the 3-D spatial city. Moreover, this method often neglects the altitude of the rail way infrastructure which has narrow width and long length. This As the results, We confirmed the solutions of varieties application for railway facilities management using 3-D spatial image contents and database design. Also, I suggested that U-city using railway modeling about matching methods of high density elevation value using 3-D aerial photo with laser data are best approach for detail stereo modeling and simulation.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.03a
• /
• pp.7-7
• /
• 2010

Energy harvesting from the environment has been of great interest as a standalone power source of wireless sensor nodes for Ubiquitous Sensor Networks(USN). In particular, the piezoelectric energy harvesting from ambient vibration sources has intensively researched because it has a relatively high power density comparing with other energy scavenging methods. Through recent advances in low power consumption RF transmitters and sensors, it is possible to adopt a micro-power energy harvesting system realized by MEMS technology for the system-on-chip. However, the MEMS energy harvesting system has some drawbacks such as a high natural frequency over 300 Hz and a small power generation due to a small dimension. To overcome these limitations, we devised a novel power generator with a spiral spring structure as shown in the figure. The natural frequency of a cantilever could be decreased to the usable frequency region (under 300 Hz) because the natural frequency depends on the length of a cantilever. In this study, the natural frequency of the energy harvester was a lower than a normal cantilever structure and sufficiently controllable in 50 - 200 Hz frequency region as adjusting weight of a proof mass. Moreover, the MEMS energy harvester had a high energy conversion efficiency using a shear mode ($d_{15}$) is much larger than a 33 mode ($d_{33}$) and the energy conversion efficiency is proportional to the piezoelectric constant (d). We expect the spiral type MEMS power generator would be a good candidate for a standalone power generator for USN.

• Clean Technology
• /
• v.10 no.3
• /
• pp.159-168
• /
• 2004

Benzene adsorption experiment was carried out for activated carbon and zeolite 13X adsorbents. Single column and dual column packed with two adsorbents were used to investigate the dynamic adsorptive characteristics. Effect of feed flow rate on the breakthrough curve was not significant. Specific adsorption amount of benzene for activated carbon was larger than that for zeolite 13X. On the contrary, adsorption amount per column volume was larger for zeolite 13X column because the density of zeolite 13X was larger. In the dynamic experiment using dual adsorbents column, length of mass transfer zone was changed by the feed direction. Breakthrough time was longer and breakthrough curve was sharper when activated carbon was packed in feed inlet and zeolite 13X was packed in column outlet. Also breakthrough time and breakthrough curve slope were affected by the packing ratio of the two adsorbents.

• The Journal of Advanced Prosthodontics
• /
• v.5 no.2
• /
• pp.84-91
• /
• 2013

PURPOSE. The aim of this study was to evaluate the stability of arginine-glycine-aspartic acid (RGD) peptide coatings on implants by measuring the amount of peptide remaining after installation. MATERIALS AND METHODS. Fluorescent isothiocyanate (FITC)-fixed RGD peptide was coated onto anodized titanium implants (width 4 mm, length 10 mm) using a physical adsorption method (P) or a chemical grafting method (C). Solid Rigid Polyurethane Foam (SRPF) was classified as either hard bone (H) or soft bone (S) according to its density. Two pieces of artificial bone were fixed in a customized jig, and coated implants were installed at the center of the boundary between two pieces of artificial bone. The test groups were classified as: P-H, P-S, C-H, or C-S. After each installation, implants were removed from the SRPF, and the residual amounts and rates of RGD peptide in implants were measured by fluorescence spectrometry. The Kruskal-Wallis test was used for the statistical analysis (${\alpha}$=0.05). RESULTS. Peptide-coating was identified by fluorescence microscopy and XPS. Total coating amount was higher for physical adsorption than chemical grafting. The residual rate of peptide was significantly larger in the P-S group than in the other three groups (P<.05). CONCLUSION. The result of this study suggests that coating doses depend on coating method. Residual amounts of RGD peptide were greater for the physical adsorption method than the chemical grafting method.

• Polymer(Korea)
• /
• v.33 no.4
• /
• pp.364-370
• /
• 2009

The curing kinetics and mechanical properties of siloxane-diaminodiphenylmethane (ETSO-DDM) on the two kinds of bisphenol (BPH) system which are DGEBA and DGEBF were investigated with the different contents of ETSO. To investigate the curing kinetics of the ETSO-DDM/BPH systems, differential scanning calorimeter (DSC) was used. The mechanical properties of ETSO-DDM/BPH systems were also examined by universal testing machine (UTM), tensile test and flexural test. From experimental results, the activation energies and mechanical properties of ETSO-DDM/BPH were improved with the decrease contents of ETSO. This was due to the high cross-linking density made from short length of ETSO-DDM, resulting in improving the mechanical inter-locking between ETSO-DDM and BPH in these systems.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.46 no.6
• /
• pp.429-433
• /
• 2001

This study was carried out to investigate the occurrence and characteristics of off-type rice plant according to agronomic conditions. The occurrence density of the off-type rice plant in farmer's paddy field was greater as the years of self-produced seed use increased, and in the direct sowing paddy field it was twice as much as in the transplanting paddy field. When the long-grain red rice and the short-grain red rice in the cultivated field of cultivar were artificially sown, in the direct sowing on a flooded paddy surface culture rather than in the machine transplanting culture the off-type rice plant occurred much more, the culm length was longer, and the number of productive culm per plant increased. These characteristics were more conspicuous in the long-grain red rice than in the short-grain red rice. In the transplanting farmer's paddy fields, the off-type rice plant that occurred outside of the hills of the cultivar rice ranged 0 to 6%. Whereas in was 70.6 to 91.9% when the long-grain red rice and short-grain red rice were artificially sown. Therefore, it was assumed that most of the off-type rice plants occurred in the farmer's paddy fields was caused by seed contamination.

• Journal of Korea Technical Association of The Pulp and Paper Industry
• /
• v.46 no.5
• /
• pp.9-18
• /
• 2014

London Convention on the prevention of marine pollution by dumping of wastes and other matter prohibits the deliberate disposal of paper mill sludges at sea. In order to explore the alternative plan on the prohibition of sludge disposal at sea, the biodegradable seedling pot was developed by mixing the sludge with old newspaper (ONP) in appropriate mixing ratios. The C/N ratio of the mixed sludge was below 20, leading to rapid deterioration of the organic matters composing the seedling pot. The increased ONP contents in the seedling pot resulted in the increase of pot thickness and thereafter in the decrease of pot density. Cellulose fibers in ONP promoted water absorption of the pot but AKD addition helped the seedling pot to repel water during raising seedling. Breaking length and burst strength of the seedling pot were improved by addition of wet strength additives but air permeability was a little diminished. Biodegradable rate of the seedling pot in a soil was accelerated by the attack of soil microbes at the beginning, and finally the pot was completely degraded in 150 days in a soil.

• Journal of the Korean Vacuum Society
• /
• v.15 no.6
• /
• pp.637-641
• /
• 2006

We present the DC and RF characteristics of 100 nm gate length InGaAs/InAlAs/GaAs metamorphic high electron mobility transistors (MHEMTs). We fabricated the T-gate with 100 nm foot print by using a positive resist ZEP520/P (MMA-MAA)/PMMA trilayer by double exposure method. The fabricated 100 nm MHEMT with a $70\;{\mu}m$ unit gate width and two fingers were characterized through do and rf measurements. The maximum drain current density of 465 mA/mm and extrinsic transconductance $(g_m)$ of 844 mS/mm were obtained with our devices. From rf measurements, we obtained the current gain cut-off frequency $(f_T)$ of 192 GHz, and maximum oscillation frequency $(f_{max})$ 310 GHz.