• 한국식품과학회지
• /
• 제30권5호
• /
• pp.1077-1084
• /
• 1998

게맛살의 관능적 조직감특성을 기계적인 측정방법을 이용하여 정량적으로 나타내기 위하여 Texture Analyser (TX-XT2, England)의 측정조건을 달리한 기계적 조직감 지표(T.P.A.)를 구하였으며, 그 결과를 관능검사 결과와 비교하였다. 부수적으로 어묵과의 조직감 차이도 조사하였다. 본 실험에 사용한 시료는 국내에서 제조판매되고 있는 5종류의 게맛살과 2종류의 어묵을 서울시내 백화점에서 구입하여 사용하였다. 게맛살과 어묵의 조직감에 대한 기계적 측정치는 경도 및 응집성, 특히 씹힘성과 껌성에서 어묵이 높은 값을 보이며 게맛살과 커다란 차이를 보였다. 평판 탐침의 직경변화$({\varphi}12.5\;mm,\;{\varphi}24.6\;mm)$가 맛살의 조직감 변수에 미치는 영향을 조사한 결과 경도와 응집성은 탐침의 직경이 증가함에 따라 증가하였으며 탄력성은 감소하였다. 압착율의 변화(60, 70, 80%)에 대한 조직감 변수의 영향은 압착율이 증가시 경도는 증가한 반면 응집성과 탄력성은 감소하였다. 변형속도가 0.8에서 2.4 mm/sec로 증가함에 따라 씹힘성, 껌성, 응집성 및 경도가 약간 증가하였다. 경도, 응집성 및 씹힘성이 기계적 측정치들과 관능검사 결과들간에 높은 상관관계를 나타내었다. 결론적으로 게맛살의 조직감에 대한 관능검사를 대신할 기계적 측정조건은 시료 직경의 약 2배가 되는 직경 24.6 mm의 평판 탐침으로, 변형속도 2.4 mm/sec에서 60%의 변형율로 2회 반복압착하여 얻은 힘-거리 곡선을 분석하는 것이 본 실험 범위내에서 바람직한 것으로 판단된다.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1996년도 춘계학술발표회논문집(2)
• /
• pp.417-422
• /
• 1996

The KNGR has an advanced ECCS design feature which employs four mechanically-separated SI trains where each train consisting of one HPSI pump and one SIT injects ECC water directly into the reactor vessel downcomer annulus. To demonstrate that the KNGR ECCS design features meet the EPRI ALWR requirements of no core uncovery for a break of up to 6 inch diameter, small break LOCA cases with various break sizes were analyzed using a best-estimate analytical procedure. Two kinds of break locations are considered: cold leg and DVI line breaks. It was observed that the KNGR ECC design can tolerate a cold leg break of up to 10 inches with no core uncovery. However. since DVI line break with 6 inch diameter undergoes slight core uncovery. further investigation is required for KNGR SIS optimization.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2003년도 추계학술발표대회 개요집
• /
• pp.191-193
• /
• 2003

S-N fatigue tests were conducted to investigate the fatigue strength of the small diameter socket and butt welded joints of carbon steels. Experimental parameters were pipe diameter, throat depth, shape of socket welds and welding procedure. Filler metals used in SMAW and GTAW procedure were E9016-G with diameter of 4.0 mm and ER70S-G with diameter of 2.4 m. API 5L Gr.B pipes were adopted as a small diameter branch pipes. All socket fittings were machined from ASTM A105 carbon steel. Fatigue strength in socket weld joints increased with increasing pipe diameter, area of weld metal and weld leg length of pipe side.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.1092-1097
• /
• 2003

S-N fatigue tests were conducted to investigate the fatigue strength of small diameter socket and butt welded joints made of carbon steels. Experimental parameters were pipe diameter, throat depth, shape of socket welds and welding procedure. Filler metals used in SMAW and GTAW procedure were E9016-G with diameter of 4.0 mm and ER70S-G with diameter of 2.4 mm. API 5L Gr.B pipes were adopted as a small diameter branch pipes. All socket fittings were machined from ASTM A105 carbon steel. Tensile strength was not affected by the welding procedure. Fatigue strength in socket weld joints increased with increasing pipe diameter, area of weld metal and weld leg length of pipe side.

• Journal of Welding and Joining
• /
• 제22권3호
• /
• pp.50-55
• /
• 2004

S-N fatigue tests were conducted to investigate the fatigue strength of small diameter socket and butt welded joints made of carbon steels. Experimental parameters were pipe diameter, throat depth, shape of socket welds and welding procedure. Filler metals used in SMAW and GTAW procedure were E9016-G with diameter of 4.0 m and ER70S-G with diameter of 2.4 m. API 5L Gr.B pipes were adopted as a small diameter branch pipes. All socket fittings were machined from ASTM A105 carbon steel. Tensile strength was not affected by the welding procedure. Fatigue strength in socket weld joints increased with increasing pipe diameter, area of weld metal and weld leg length of pipe side.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2007년도 춘계학술대회A
• /
• pp.1167-1172
• /
• 2007

Generally inpipe robot needs force above standing for contacting robot to pipe. If the environment of the pipe-inside does not change, there is not a problem. But if the pipe radius change, or occur the obstacle which it does not intend, problem gets. So it uses a different system and must know an environment change, and changing the shape or a form of the robot. The research uses the flexible leg and is the robot which is adapted to the environment change of the pipe. The advantage of this robot is possible to move when it does not need to recognize a change of environment of pipe. Leg is bend with one direction. When it moves part that there are legs effect of leg direction the robot is moved with only one direction. If friction between legs and pipe is sufficient, not only verticality pipe moving, but also curved pipe moving. Also the obstacle of the pipe inside occurs and the diameter of the pipe inside changes, this robot can move if it does not use another system or device.

• Nuclear Engineering and Technology
• /
• 제31권6호
• /
• pp.548-560
• /
• 1999

An experimental investigation has been peformed to examine the effects of various geometrical parameters and an initial operating condition on the air-water countercurrent How limitation (CCFL) in a simulated PWR hot leg. A total of 118 experimental data for the onset of CCFL and zero liquid penetration were obtained for various combinations of test parameters. It was observe that the CCFL can be classified into three different categories: (the onset of CCFL, (the partial liquid delivery, and (r) the zero liquid penetration. The observed mechanisms of the onset of CCFL were different depending on the inlet water flow rate. The parametric effects of pipe diameter, horizontal pipe length, horizontal pipe length-to-diameter (L/D) ratio, and initial water level in the horizontal pipe of the test section on the onset of air-water CCFL were also examined. An empirical correlation for the onset of CCFL in a horizontal pipe connected to an inclined riser was developed in terms of Wallis flooding parameters for the low inlet water flow rate region. Comparisons of the present empirical correlation with the air-water CCFL data of large pipe diameters show that the present correlation agrees more closely with the experimental data than the existing CCFL correlations.

• 마이크로전자및패키징학회지
• /
• 제25권4호
• /
• pp.67-74
• /
• 2018

두께가 $20{\mu}m$이며, 직경이 각기 $100{\mu}m$, $300{\mu}m$, $500{\mu}m$인 p형 $Sb_2Te_3$와 n형 $Bi_2Te_3$ 박막레그들을 전기도금하여 열전박막모듈을 형성한 후, 박막레그의 직경에 따른 출력전압과 출력전력을 비교하였다. $100{\mu}m$ 직경 박막레그들로 구성된 모듈은 ${\Delta}T=36.7K$에서 365 mV, $300{\mu}m$ 직경 박막레그들로 형성한 모듈은 ${\Delta}T=37.5K$에서 142 mV, $500{\mu}m$ 직경 박막레그들로 제작한 모듈은 ${\Delta}T=36.1K$에서 53 mV의 open circuit 전압을 나타내었다. $100{\mu}m$ 직경 박막레그 모듈은 ${\Delta}T=36.7K$에서 $845{\mu}W$, $300{\mu}m$ 직경 박막레그 모듈은 ${\Delta}T=37.5K$에서 $631{\mu}W$, $500{\mu}m$ 직경 박막레그 모듈은 ${\Delta}T=36.1K$에서 $276{\mu}W$의 최대출력전력을 나타내었다.

• 대한치과보철학회지
• /
• 제41권2호
• /
• pp.169-181
• /
• 2003

Statement of problem : The survival rate of wide diameter implants was lower than of 3.75-mm implants in some clinical researches. Purpose : The purpose of this study was to investigate the influence of implant diameter on the osseointegration of implants in the rabbit femoral condyle and tibial metaphyses by means of removal torque measurements and histomorphometric analysis. Material and Method : Ten adult New Zealand White rabbits were used in this study Two 3.75-mm diameter implants were inserted through one cortical layer in the tibial metaphyses and one 3.75-mm diameter implant was inserted in the femoral condyle. 5.0-mm diameter implants were inserted in the other leg in the same manner. A total of 60 implants (3.75-mm diameter implants:30 : 5.0-mm diameter implants:30) were installed. After a healing time of 4 and 12 weeks, the peak removal torque values required to shear off the implants were recorded. From the removal torque values (Ncm) obtained, the mean shear stress ($N/mm^2$) was calculated. And the percentage of direct bone-to-implant contact and the percentage of bone area inside the thread were measured by Kappa Image Base-metreo. The Student's t-test was undertaken for statistical analysis (p<0.05). Results : The removal torque value of 5.0-mm diameter implants was higher than of 3.75-mm diameter implants (p<0.05). The difference of shear stress value between 3.75-mm and 5.0-mm diameter implants was not statistically significant (p>0.05). The percentage direct bone-to-implant contact had no statistical difference between two groups (p>0.05). The percentage of bone area inside the thread had no statistical difference between two groups (p>0.05). Conclusion It is concluded that the quality f osseointegration is not influenced by increasing implant diameter.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2000년도 춘계학술대회 논문집
• /
• pp.69-74
• /
• 2000

Linear and nonlinear motion responses of a Tension Leg Platform(TLP) was investigated by model tests. The model tests were carried out at KRISO's Ocean Engineering Basin which has a deep pit of which diameter and depth are 5 meters and 12.5 meters, respectively. Optical sensors were used for measuring drift motions, and a set of accelerometers were employed for analyzing wave frequency motions. ISSC TLP was chosen as the model for the present study. Scale ratio was 1/65 and elastic modelling of tether system were conducted. Very good agreement was obtained between experimental results and theoretical calculations not only in linear motion responses but tension responses, nonlinear wave drift force and double frequency excitations.