• International Journal of Naval Architecture and Ocean Engineering
• /
• 제11권1호
• /
• pp.510-520
• /
• 2019

To investigate the morphology characteristics of air layer in the air cavity, a numerical method with the combination of RANS equations and VOF two-phase-flow model is proposed for a plate with air cavity. Based on the model above, the dynamic and developmental process of air layer in the air cavity is studied. Numerical results indicate that the air layer in the plate's air cavity exhibits the dynamic state of morphology and the wavelength of air layer becomes larger with the increasing speed. The morphology of air layer agrees with the Froude similarity law and the formation of the air layer is not affected by the parameters of the cavity, however, the wave pattern of the air layer is influenced by the parameters of the cavity. The stable air layer under the air cavity is important for the resistance reduction for the air layer drag reduction.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 추계학술대회 논문집
• /
• pp.281-283
• /
• 2001

Bi$_2$Sr$_2$CuO$\_$x/(Bi-2201) thin films were fabricated layer-by-layer deposition using an ion beam sputtering method. 10 wt% and 90 wt% ozone mixed with oxygen were used ultraviolet light irradiation to assist oxidation. At early stages of the atomic layer by layer deposition, two dimensional epitaxial growth which covers the substrate surface would be suppressed by the stress and strain caused by the lattice misfit, then three dimensional growth takes place. Since Cu element is the most difficult to oxidize, only Sr and Bi react with each other predominantly, and forms a buffer layer on the substrate in an amorphous-like structure, which is changed to SrBi$_2$O$_4$ by in-situ anneal.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 2017년도 춘계학술대회 논문집
• /
• pp.97-97
• /
• 2017

This study investigated the corrosion protection by electrodeposited copper layer on AZ31 Mg alloy with and without additional silver layer by immersion test, salt spray test, OCP transient and potentiodynamic polarization experiment. The single electrodeposited Cu layer on AZ31 Mg alloy showed a nodular structure with many imperfections of crevices between the nodules, which resulted in the fast initiation of pitting corrosion within first few hours of immersion. Double-layer coating of Cu and outer Ag layer slightly increased the initiation time for pitting corrosion. Triple-layer coatings of Cu/Ag/Cu exhibited the most efficient corrosion protection of AZ31 Mg alloy, compared to the single- and double-layer coatings. Surface morphology of the outer Cu layer in the triple-layer was changed from the nodular structure to fine particle structure with no crevices due to the presence of an additional Ag layer. Thus, the improved corrosion resistance of AZ31 Mg alloy by electrodeposited Cu/Ag or Cu/Ag/Cu layers is readily ascribed to the decreased number of imperfections in the electrodeposited layers due to the additional silver layer. It is concluded that the additional silver layer provides many nucleation sites for the second Cu plating, resulting in the formation of finer and denser structure than the first Cu electrodeposit.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.337-337
• /
• 2011

The elecronic absorption and surface morphology evolution of two types of molecular double layer thin films, copper phthalocyanine(CuPc) layer deposited on top of chloro[subphtalocyaninato]boron(III) (SubPc) layer, denoted as SubPc/CuPc, and vice versa, at various thicknesses were invertigated using ultraviolet(UV)-visible spectroscopy and atomic force microscopy (AFM). Both types of double layer structures showed similar broadened absorption patterns in UV-visible region which were well consistent with fitted spectra by a simple linear combination of single layer absorption spectra of two materials. In contrast, the surface morphology of double layer structures was dependent on the order of deposition. For CuPc/SubPc structures, the surface morphology was characterized by elongated grains, characteristic of SubPc thin films, indicating the morphological influence of underlying CuPc layer on subsequent SubPc layer was not large. For SubPc/CuPc structures, however, the underlying SubPc layer acted as a morphological template for the subsequently deposited CuPc layer. It was also observed that the grain size of CuPc layer varied by the thickness of underlying SubPc layer.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 1997년도 추계학술대회 논문집
• /
• pp.432-435
• /
• 1997

In AC PDP, electrodes are covered with dielectric layer and the discharge is formed on the surface of the dielectric layer. MgO protection layer on the dielectric layer in PDP prevents a dielectric layer from sputtering and lowers the firing voltage due to a large secondary electron emission yield( ${\gamma}$ ). Until now, the MgO protection layer is mainly prepared by E-beam evaporation. However, there are some problems that is easy pollution and change of its characteristics with time and delamination. Therefore, in this study, MgO protection layer is prepared on dielectric layer by reactive R.F. magnetron sputtering with MgO target. Discharge characteristics and secondary electron emission coefficients of PDP are studied as a parameter of preparation conditions. Discharge voltage characteristics of the prepared MgO layer can be stable and improved by the annealing process in vacuum chamber.

• 한국농공학회지
• /
• 제16권3호
• /
• pp.3477-3491
• /
• 1974

Following are the results of the study on the property of falling permeation of stratified soil in the close state under existence of stagnant water on a soil layer. 1. When on the stratified soil a least permeating layer was put on the soil layer the load Pressure was present owing to appearance of saturation close state driving decrease of the pressure in the lower layer, on the other hand when the least permeating layer was placed under the layer the lower least permeating layer pressure was decreased. 2. In the case of least permeating layer the variation of current gradient according to the respective level after treating the layer was enormous and due to usal storage phenomena for the Kl layer which was coarse that was trifle. 3. The permeability of the respective layer of stratified soil in the close state died not always coincide with that of single layer. 4. Generally Zunker's equation of average permeability was valid but actually calculated permeating velocity after treating the layer of stratified soil was seriously differ from the measured value owing to the variation of current gradient, especially when the pressure head at the layer boundany was discontinuous the validity of the equation of average permeability was seemed to be doubtful. 5. The permeating velocity of stratified soil was regulated by the least permeating layer, i.e. it is thought to be rational to estimate the value by calculating the current gradient with its proper permeability, pressure headon the layer and its thickness.

• 한국표면공학회지
• /
• 제51권1호
• /
• pp.21-26
• /
• 2018

The $Cu_2(btc)_3$ metal-organic frameworks (MOF) coated anodic aluminum oxide (AAO) membrane was successfully prepared by layer-by-layer technique using hand spray method. It was confirmed that the $Cu_2(btc)_3$ layer, which has the pore sized in 2-3 nm, on surface of AAO exhibited the polycrystalline thin film structure by XRD analysis. More than 100 repetitive spray cycles were required to obtain more robust and thick MOFs on AAO and it was possible to uniformly coat both the top and bottom surfaces of the AAO. It should be noted that the MOFs also could be coated on surface of pores resulting in reduce the size of pore from 52 nm to 32 nm.

• 한국멀티미디어학회논문지
• /
• 제19권12호
• /
• pp.1992-1999
• /
• 2016

In layered communication architecture, each layer is designed to service its own functions to higher layer while getting serviced by lower layer. Usually layered architectures are not optimized in a total view of whole services and functions. So cross layer design pursues performance enhancements by optimizing in various ways. In LTE, MAC layer uses HARQ mechanism and RLC layer uses ARQ mechanism for retransmission. According to the 3GPP 36.331 specification, two layers' cooperation may not happen in an optimized way. This paper suggests an adaptive MAC layer approach which RLC layer's function might be initiated in MAC layer in advance to utilize MAC layer's idling wasting time for RLC layer's next decision. This adaptive ARQ method in MAC layer speeds up the next retransmission and reduces the overall transmission time. Emulation shows the improved performance in total retransmission time and retransmission success ratio. In wireless shadow area, the retransmission occurs frequently. Our approach has strong points in this poor wireless condition.

• 한국정보통신학회:학술대회논문집
• /
• 한국해양정보통신학회 2003년도 춘계종합학술대회
• /
• pp.518-521
• /
• 2003

Bi$_2$Sr$_2$Ca$_{n-1}$Cu$_{n}$O$_{x}$ superconducting thin films have been fabricated by atomic layer-by-layer deposition using IBS(Ion Beam Sputtering) method. During the deposition, 90 mol% ozone gas of typical pressure of 1~9 $\times$ 10$^{-5}$ Torr are supplied with ultraviolet light irradiation for oxidation. XRD and RHEED investigations reveal out that a buffer layer with some different compositions is formed at the early deposition stage of less than 10 units cell and then Bi-2201 oriented along the c-axis is grown.grown.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2013년도 제44회 동계 정기학술대회 초록집
• /
• pp.274-274
• /
• 2013

We fabricate encapsulation-layer of OLED panel from organic-inorganic hybrid thin film by atomic layer deposition (ALD) molecular layer deposition (MLD) using Al2O3 as ALD process and Adipoyl Chloride (AC) and 1,4-Butanediamine as MLD process. Ellipsometry was employed to verify self-limiting reaction of MLD. Linear relationship between number of cycle and thickness was obtained. By such investigation, we found that desirable organic thin film fabrication is possible by MLD surface reaction in monolayer scale. Purging was carried out after dosing of each precursor to eliminate physically adsorbed precursor with surface. We also confirmed roughness of the organic thin film by atomic force microscopy (AFM). We deposit AC and 1,4-Butanediamine at $70^{\circ}C$ and investigated surface roughness as a function of increasing thickness of organic thin film. We confirmed precursor's functional group by IR spectrum. We calculated WVTR of organic-inorganic hybrid super-lattice epitaxial layer using Ca test. WVTR indicates super-lattice film can be possibly use as encapsulation in flexible devices.