• Proceedings of the KSME Conference
• /
• 2007.05b
• /
• pp.3039-3044
• /
• 2007

A few fluid structure interaction analyses have been developed for turbomachinery blades in comparison with aircraft wings. Also, the existing aeroelastic analyses for turbomachinery blades have been mostly limited to cases with a steady freestream. In reality, however, the inflowing freestream is often pulsating. Therefore, this paper presents stability and forced response analyses of an isolated three-dimensional blade under pulsating freestream conditions. A new three-dimensional unsteady vortex lattice model under a pulsating freestream has been developed in discrete time domain to examine unsteady aerodynamic forces acting on a vibrating blade. The blade's structural behaviors have been analyzed by using a three-dimensional plate model. In the aeroelastic analysis, the flutter onset of a blade under pulsating freestream is predicted by the Floquet analysis. The new time domain method can predict aeroelastic stability as well as time history.

• Journal of Magnetics
• /
• v.17 no.1
• /
• pp.6-8
• /
• 2012

M$\ddot{o}$ssbauer spectra of hexagonal $BaFe_{12}O_{19}$ single crystals were studied at various temperatures (4-300 K). It was found that the spin states in Fe atoms were parallel to the ${\gamma}$-ray's direction into a single crystal along the caxis. The location of the Fe ion in the 2b site is unusual in an oxide structure and has strong anisotropic lattice vibrations. Moreover, at room temperature, the zero absorption lines of the Fe ions at the 2b site were observed due to fast diffusion motion in a double well atomic potential. The two Fe ions of the single crystal mainly enter into the sites in the mirror plane of the trigonalbipyramidal structure.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.158-160
• /
• 1997

WHEN IT IS REQUIRED TO CONNECT OVERHEAD TRANSMISSION LINE WITH UNDERGROUND CABLE, PREVALENT METHOD WAS TO USE CABLE HEAD TYPICALLY MADE OF LATTICE STEEL STRUCTURE. BUT IN VIEW OF THE INCREASING DEMAND THAT STEEL STRUCTURE INSTALLED IN URBAN AREA AND/OR RESIDENTIAL AREA NEED TO MATCH WITH ENVIRONMENTAL SURROUNDINGS, THE UNSHAPELY LARGE-SIZED LATTICE STEEL STRUCTURE CAN NOT BE A PROPER ONE BECAUSE THAT IT IS NOT WELCOMED BY THE RESIDENTS AND ACCORDINGLY ITS INSTALLATION TENDS TO CONFRONT WITH CIVIL PETITION. AS AN ALTERNATIVE METHOD TO SETTLE AFOREMENTIONED UNFAVOURABLE SITUATION WE MAY BE UNDER, WE AR INTENDING TO DEVELOP THE CABLE HEAD MADE OF TAPERED TUBULAR STEEL POLE AND TO PUT IT TO PRACTICAL USE. THE ADVANTAGE WE CAN TAKE OF THE TAPERED TUBULAR STEEL POLE IS THAT IT CAN BE INSTALLED IN A VERY LIMITED SPACE MAXIMIZING THE UTILITY VALUE OF THE LAND AND THAT ITS SMART SHAPE WITH COLOUR COATING IN CONSIDERATION OF AESTHETIC AESTHETIC CAN BE IN GOOD HARMONY WITH THE SURROUNDINGS.

• Korean Journal of Materials Research
• /
• v.17 no.7
• /
• pp.358-360
• /
• 2007

Cobalt subtitution on NiSi is investigated by using an ab-initio calculation. Firstly, a relaxed NiSi structure is calculated and the calculated lattice parameters are compared with experimentally determined lattice parameters. The calculated values are smaller than the experimental values by about 2%. As the calculation is based on 0 K, and the experimental measurement is performed at room temperature, those values are in good agreement. Next, a Co atom substitutes a Ni and Si site, respectively, to evaluate the preferable site between them. Co prefers Ni site to Si site. The calculated total energy also indicates that the Co substitution to Ni site stabilizes the NiSi structure. Therefore, the thermal stability of NiSi with Co addition can be achieved by the structure stabilization of NiSi by Co substitution into Ni site of NiSi.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.05c
• /
• pp.170-173
• /
• 2003

In this paper, we proposed a new bulk LDMOS structure which can be used for RF application, and its fabrication steps were introduced. The simulated devices consist of three types: Bulk device, SLB(SOI Like Bulk), and SOI device. As a result of process and device simulation, we showed electrical characteristics, such as threshold voltage, subthreshold slope, DIBL(Drain Induced Barrier Lowering), off-state current, and breakdown voltage. In this simulation study, the lattice temperature model was adopted to see the device characteristics with lattice temperature during the operation. SLB device structure showed the best breakdown characteristics among the other structures. The breakdown voltage of SLB structure is about 9V, that of bulk is 7V, and that of SOI is 8V.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.13 no.2
• /
• pp.1003-1019
• /
• 2019

Threshold ring signature scheme enables any t entities from N ring members to spontaneously generate a publicly verifiable t-out-of-N signature anonymously. The verifier is convinced that the signature is indeed generated by at least t users from the claimed group, but he cannot tell them apart. Threshold ring signatures are significant for ad-hoc groups such as mobile ad-hoc networks. Based on the lattice-based ring signature proposed by Melchor et al. at AFRICRYPT'13, this work presents a lattice-based threshold ring signature scheme, employing the technique of message block sharing proposed by Choi and Kim. Besides, in order to avoid the system parameter setup problems, we proposed a message processing technique called "pad-then-permute", to pre-process the message before blocking the message, thus making the threshold ring signature scheme more flexible. Our threshold ring signature scheme has several advantages: inherits the quantum immunity from the lattice structure; has considerably short signature and almost no signature size increase with the threshold value; provable to be correct, efficient, indistinguishable source hiding, and unforgeable.

• Journal of Korean Society of Steel Construction
• /
• v.24 no.3
• /
• pp.267-278
• /
• 2012

In general, the H-shaped steel ribs or triangular lattice girders have been mostly used in constructing tunnels through the NATM construction method. The H-shaped steel rib has higher flexural and axial strength than the triangular lattice girder, but many unexpected gaps can occur in the concrete lining system after shotcreting if the H-shaped steel rib is used as the support system. To achieve better shotcreting quality, the triangular lattice girder was developed. However, in general, the triangle lattice girder has low flexural and axial strength. Likewise, the triangular lattice girder, which has circular sectional members, has so many fractures from welded points at the joints between the members. Finally, the new type of tetragonal lattice girder was developed to overcome those problems. In this study, the structural performance of the tetragonal lattice girders was evaluated through analytical and experimental studies. In the analytical studies, the four-point bending analysis, the traditional evaluation method to determine the flexural strength of the lattice girder, was performed. Moreover, the linear-elastic analysis and stability analysis of the arch structure made by the lattice girders were performed to measure structural performance. Experiments were likewise performed to compare the structural performances of the tetragonal girder with traditional triangular lattice girders.

• Structural Engineering and Mechanics
• /
• v.84 no.5
• /
• pp.591-604
• /
• 2022

A gravity wall combined with an anchoring lattice frame (a combined retaining structure) is adopted at a typical engineering site at Dali-Ruili Railway Line China. Where, the combined retaining structure supports a soil deposit covering on different inclined rock slopes. With an aim to investigate and compare the effects of inclined rock slopes on the response of combined retaining structure under seismic excitation, three groups of shaking table tests are conducted. The rock slopes are shaped as planar surfaces inclined at angles of 20°, 30°, and 40° with the horizontal, respectively. The shaking table tests are supplemented by dynamic numerical simulations. The results regarding the horizontal acceleration response, vertical acceleration response, permanent displacement mode, and axial anchor force are comparatively examined. The acceleration response is more susceptible to outer structural profile of combined retaining structure than to inclined angle of rock slope. The permanent displacement decreases when the inclined angle of the rock slope increases within a range of 20°-40°. A critical inclined angle of rock slope exists within a range of 20°-40°, and induces the largest axial anchor force in the combined retaining structure.

• Korean Journal of Materials Research
• /
• v.21 no.12
• /
• pp.697-702
• /
• 2011

Two-dimensional (2D) nano patterns including a two-dimensional Bravais lattice were fabricated by laser interference lithography using a two step exposure process. After the first exposure, the substrate itself was rotated by a certain angle, $90^{\circ}$ for a square or rectangular lattice, $75^{\circ}$ for an oblique lattice, and $60^{\circ}$ for a hexagonal lattice, and the $90^{\circ}$ and laser incident angle changed for rectangular and the $45^{\circ}$ and laser incident angle changed for a centered rectangular; we then carried out a second exposure process to form 2D bravais lattices. The band structure of five different 2D nano patterns was simulated by a beam propagation program. The presence of the band-gap effect was shown in an oblique and hexagonal structure. The oblique latticed ZnO nano-photonic crystal array had a pseudo-bandgap at a frequency of 0.337-0.375, 0.575-0.596 and 0.858-0.870. The hexagonal latticed ZnO nano-crystallite array had a pseudo-bandgap at a frequency of 0.335-0.384 and 0.585-0.645. The ZnO nano structure with an oblique and hexagonal structure was grown through the patterned opening window area by a hydrothermal method. The morphology of 2D nano patterns and ZnO nano structures were investigated by atomic force microscopy and scanning electron microscopy. The diameter of the opening window was approximately 250 nm. The height and width of ZnO nano-photonic crystals were 380 nm and 250 nm, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.22 no.6
• /
• pp.19-26
• /
• 2021

The lattice structure is attracting attention from industry because of its excellent strength and stiffness, ultra-lightweight, and energy absorption capability. Despite these advantages, widespread commercialization is limited by the difficult manufacturing processes for complex shapes. Additive manufacturing is attracting attention as an optimal technology for manufacturing lattice structures as a technology capable of fabricating complex geometric shapes. In this study, a unit cell was formed using a three-dimensional coordinate method. The relative density relational equation according to the boundary box size and strut radius of the unit cell was derived. Simple cubic (SC), body-centered cubic (BCC), and face-centered cubic (FCC) with a controlled relative density were designed using modeling software. The accuracy of the equations for calculating the relative density proposed in this study secured 98.3%, 98.6%, and 96.2% reliability in SC, BCC, and FCC, respectively. A simulation of the lattice structure revealed an increase in compressive yield load with increasing relative density under the same cell arrangement condition. The compressive yield load decreased in the order of SC, BCC, and FCC under the same arrangement conditions. Finally, structural optimization for the compressive load of a 20 mm × 20 mm × 20 mm structure was possible by configuring the SC unit cells in a 3 × 3 × 3 array.