• 전력전자학회논문지
• /
• 제9권2호
• /
• pp.105-111
• /
• 2004

본 논문에서는 온도나 습도 등 주변 환경변화와 무관하게 항상 최적의 레이저 프리터의 출력특성을 유지하기 위한 OPC(Organic Photo Conductor)용 고압 전류형 전원특성에 관한 논문이다. 제안된 제어방식은 기존의 정전압 제어방식이 가지는 단점인 온도나 습도 및 OPC의 분포저항 변화에 따른 출력전류 변동으로 OPC 표면에 일정한 전위를 형성하는 것이 용이하지 않은 단점을 개선하고, 주변환경 변화요인을 프린터 주제어기에서 감지하여 최적의 출력전류 기준신호를 출력하고, 이 기준신호에 따라 최종 출력전류가 제어되어 일정한 화상상태가 유지되도록 제어하는 제어방식으로 실험을 통하여 제안된 제어방식의 타당성을 검증하였다.

• 한국소음진동공학회논문집
• /
• 제22권4호
• /
• pp.318-327
• /
• 2012

The operating sound radiated from a laser printer includes tonal noise components caused by the rotating mechanical parts such as gear, shaft, motor, fan, etc. The negative effects of the tonal noise components need to be considered in the process of developing a sound quality index for the quantitative evaluation of the emotional satisfaction in terms of psycho-acoustics. However, in a previous paper, it was confirmed that the Aures tonality did not have enough correlation with the results of jury evaluation. The sound quality index based on loudness, articulation index, fluctuation strength has a little problem in considering the effects of rotating mechanical parts on the sound quality. In this paper, to solve the tonality evaluation problem, the calculation algorithm of Aures tonality was investigated in detail to find the cause of decreasing the correlation. The new tonality evaluation model was proposed by modifying and optimizing the masking effect, loudness ratio, and shape of weighting curve based on the basic algorithm of Aures tonality, and applied to two kinds of operating sound groups in order to verify the usefulness of proposed model. As a result, it is confirmed that the proposed tonality evaluation model has enough correlation and usefulness for expressing the tonalness in the operating sounds of laser printers. In the following paper, this results will be used to model the sound quality index as the input data by using the classification algorithm.

• 한국안광학회지
• /
• 제3권1호
• /
• pp.181-188
• /
• 1998

한글 자의 가독도를 조사하기 위해, ㄱ, ㄴ, ㄷ, ㄹ, ㅁ, ㅂ, ㅅ, ㅇ, ㅈ, ㅋ, ㅌ, ㅍ, ㅎ의 14 자음과 ㅏ, ㅓ, ㅗ, ㅜ, ㅡ, ㅣ의 6 모음 자들로 조합된 총 98개의 ($14{\times}7$) 고딕체 글자들로 3가지 형태의 시표를 레이저 프린터로 제작했다. 시력이 1.5인 사람들로 하여금 인쇄된 글자들을 판독하게 하는 방법과, 레이저 프린터의 해상력을 이용하는 방법을 사용했다. 이들 방법으로 구해진 데이터는 글자가 판독될 수 있는 최대거리 값들과 글자의 최소크기 값들이다. 값들로부터 ㄱ자의 가독도를 1로 하는 상대적 가독도를 구하였다. 이 상대적 가독도 값들을 분석한 결과 ㄱ, ㄴ, ㅅ, ㄷ, ㅈ, ㅇ, ㅁ, ㅋ, ㅌ, ㅍ, ㅎ의 순서에 따라 이들 자음이 사용된 글자의 가독도가 점점 낮아 졌다. 또한, ㅣ, ㅡ, ㅏ, ㅗ, ㅓ, ㅜ의 순서에 따라 이들 모음이 사용된 글자의 가독도가 작아졌다. 그리고 글자의 가독도는 자음이 바뀜에 따른 변화가 모음자가 바뀜에 따른 변화 보다 더 컸다.

• 기술혁신연구
• /
• 제23권3호
• /
• pp.115-135
• /
• 2015

사실상의 표준 등장은 산업의 경쟁적 상황의 변화를 가져오는 주요한 사건이며, 등장 이전의 디자인 경쟁에서 등장 이후 제품 경쟁으로 경쟁상황을 변화시킨다. 이는 사실상의 표준 등장이 산업의 발전과 기업의 전략수립에 주요한 변환점이 된다는 의미이다. 하지만, 현재까지 이러한 사실상의 표준과 기업 퇴출에 대한 연구는 미미한 실정이다. 본 연구에서는 1983년부터 2002년까지 미국의 레이저 프린터 산업을 대상으로 사실상의 표준 등장 이후, 기업퇴출에 대한 연구를 수행하고자 한다. 이를 위해 Cox의 비례위험모형을 사용하였으며, 제품수준 6650개의 표본을 바탕으로, 총 119개 회사를 대상으로 분석하였다. 이 연구의 결과는 다음과 같다. 사실상의 표준 등장 이전에 진입한 기업일수록 퇴출될 확률이 증가하였다. 사실상의 표준 등장 이후, 시장에서 경쟁기업 수가 많은 경우에는 기업의 퇴출 확률이 줄어들었으며, 제품 경쟁이 심해질수록 퇴출 확률이 증가하는 것으로 나타났다. 본 연구의 결과는 사실상의 표준 등장 이후 산업의 독특한 경쟁상황을 나타내고 있다. 이를 바탕으로, 사실상의 표준 등장에 따른 산업의 경쟁적 환경에 대한 전략적 그리고 정책적 함의를 도출하였다.

• 대한기계학회논문집A
• /
• 제35권5호
• /
• pp.575-582
• /
• 2011

클리닝 블레이드는 레이저 프린터 토너 카트리지에 장착된 감광드럼 표면의 잔류 토너를 제거하는 우레탄 재질의 고무부품이다. 기존에는 고무 블레이드의 클리닝 성능과 수명에 대한 다양한 연구들이 수행되었으나, 본 연구에서는 클리닝 성능과 부품간의 간섭에 대한 구속조건들을 모두 만족하면서 클리닝 블레이드에 발생하는 최대응력을 최소화 하는 클리닝 블레이드의 형상최적설계를 수행하였다. 상용 PIDO 툴인 PIAnO 를 이용하여 클리닝 블레이드의 구조해석절차를 통합하고 자동화하였으며, 최적설계를 위해 PIAnO 에서 제공하는 실험계획법과 근사화기법, 최적화 알고리즘을 사용하였다. 최적설계 결과, 초기 모델 대비 최대응력을 32.6% 감소 시킬 수 있는 최적의 설계안을 도출하였으며, 이를 통해 본 연구에서 수행한 최적설계 방법의 유효성을 확인할 수 있었다.

• 한국산업보건학회지
• /
• 제26권2호
• /
• pp.188-197
• /
• 2016

Objectives: The purpose of this study was to evaluate the ozone exposure levels and the variations in ozone concentration in a semiconductor fabrication facility and office in relation to the ozone concentration in the outdoor air. Methods: This study was performed in an office, semiconductor fabrication facility(such as etching, diffusion, diffusion plenum), and outdoors from June to August, 2015. Measurements were taken six times at the same places using an active sampler(pumped) and real-time equipment. Ozone monitoring by the active sampler method and analysis were carried out by OSHA Method ID-214. Real-time measurement was carried out by ozone measuring equipment using a non-dispersive ultraviolet absorption method. Results: Ozone concentrations in the semiconductor fabrication facility and office were 0.7~7.1 ppb in area samples and 0.72~4.07 ppb in real-time measurement, which were 0.88~8.88% of the occupational exposure limit. The concentration of ozone generated by a laser printer in the office was less than 2 ppb. There was not a significant difference between ozone concentrations before and after using the laser printer. The indoor/outdoor concentration ratio(I/O ratio) in the semiconductor fabrication facility and office was 0.05 and 0.06, respectively. Conclusions: All the samples contained ozone levels lower than the occupational exposure limit and it was confirmed that the concentration of outdoor ozone had no significant effect on indoor ozone concentration.

• 펄프종이기술
• /
• 제45권3호
• /
• pp.1-8
• /
• 2013

Hanji has been used mainly for preservation paper because of superior mechanical properties. However, it was not used in printing for inkjet and laser printer-printed letters. In this study, machine-made Hanji was prepared with five different contents of paper mulberry 20, 40, 60, 80 and 100% and managed by same pressure calendering. By increasing of paper mulberry contents, tearing index and folding endurance of machine-made Hanji increased because of increased fiber-to-fiber bonding. Printability property of machine-made Hanji improved by decreasing of paper mulberry contents. After 20 hours accelerated aging, the initial folding endurance of machine-made Hanji was reduced by approximately one-fourth degree. Between 40 and 100% contents of paper mulberry was showed similar levels about preservation property. The machine-made Hanji of paper mulberry 60% content was suitable for permanence and printability properties using preservation paper and printer-printed letters.

• 한국치위생학회지
• /
• 제19권6호
• /
• pp.1067-1075
• /
• 2019

Objectives: The present study aimed to compare the accuracy of removable partial denture (RPD) frameworks fabricated by selective laser sintering (SLS) before and after electropolishing. Methods: A partially edentulous mandibular model was used as the working model. Scanning of the model was performed using a dental scanner. The framework was designed using CAD software. The metal framework was formed using an SLS 3D printer. 3D scans of the two fabricated prototypes produced before and after electropolishing were overlapped with reference data. The fit was calculated based on Root Mean Square (RMS). Fabrication accuracy was verified using the paired t-test to compare the discrepancy before and after electropolishing. Results: The mean (SD) values of RMS before and after electropolishing were 126.6 (34.19) and 75.86 (21.36), respectively. There was a statistically significant difference before and after electropolishing (p<0.05). Conclusions: Metal frameworks made with SLS 3D printers showed clinically acceptable fit after electropolishing.

• 한국기계가공학회지
• /
• 제14권4호
• /
• pp.43-48
• /
• 2015

A focal length-correcting lens called the F-theta lens is required to compensate for the different focus on spot size due to the deflected incident laser beam. The F-theta lens was designed by the ray tracing method and fabricated by a 3D printer with polymer-based material. The designed F-theta lens is able to compensate for the focus on spot size by an incidence angle of 0 to 2 degrees. Based on the analysis of the simulation, there was almost no aberration in the $0^{\circ}C$ incidence angle, and the maximum of $50{\mu}m$ of aberration was observed at the incidence angle of $2^{\circ}$. Diffraction-encircled energy was analyzed to characterize the designed optics, and an image simulation was performed to confirm the actual image resolution.

• Smart Structures and Systems
• /
• 제18권3호
• /
• pp.601-623
• /
• 2016

Precast concrete elements are widely used in the construction of buildings and civil infrastructures as they provide higher construction quality and requires less construction time. However, any abnormalities in precast concrete surfaces such as non-flatness or distortion, can influence the erection of the elements as well as the functional performance of the connections between elements. Thus, it is important to undertake surface flatness and distortion inspection (SFDI) on precast concrete elements before their delivery to the construction sites. The traditional methods of SFDI which are conducted manually or by contact-type devices are, however, time-consuming, labor-intensive and error-prone. To tackle these problems, this study proposes techniques for SFDI of precast concrete elements using laser scanning technology. The proposed techniques estimate the $F_F$ number to evaluate the surface flatness, and estimate three different measurements, warping, bowing, and differential elevation between adjacent elements, to evaluate the surface distortion. The proposed techniques were validated by experiments on four small scale test specimens manufactured by a 3D printer. The measured surface flatness and distortion from the laser scanned data were compared to the actual ones, which were obtained from the designed surface geometries of the specimens. The validation experiments show that the proposed techniques can evaluate the surface flatness and distortion effectively and accurately. Furthermore, scanning experiments on two actual precast concrete bridge deck panels were conducted and the proposed techniques were successfully applied to the scanned data of the panels.