• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.188-193
• /
• 2013

The large mass method for dynamic analysis of statically determinate beams subjected to in-phase support motions is justified by showing that the equation of motion of the beams under consideration is equivalent to that of large mass model of the beam when an appropriate large mass ratio is employed. The accuracy of the stress responses based on the beam large mass method is investigated through careful numerical tests. The numerical results are compared to analytic solutions and the comparison shows that the large mass method yields not only the time history of motion but also the distributions of bending moment and shear force accurately.

• Nuclear Engineering and Technology
• /
• v.43 no.4
• /
• pp.361-374
• /
• 2011

Two types of numerical modeling techniques were considered for the dynamic response of a structure subjected to a ground acceleration. One technique is based on the equation of motion relative to ground motion, and the other is based on the equation of absolute motion of the structure and the ground. The analytic background of the former is well established while the latter has not yet been extensively verified. The latter is called a large mass method, which allocates an appropriate large mass to the ground so that it causes the ground to move according to a given acceleration time history. In this paper, through the use of a single degree-of-freedom spring-mass system, the equations of motion of the two techniques were analyzed and useful theorems are provided on the large mass method. Using simple examples, the numerical results of the two modeling techniques were compared with analytic solutions. It is shown that the theorems provide a clear insight on the large mass method.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1998.05a
• /
• pp.553-558
• /
• 1998

The calibrating method for an electrochemical Probe, neglecting the effect of the normal velocity on the mass transport, can cause large errors when applied to the measurement of wall shear rates in thin wavy flow with large amplitude waves. An extended calibrating method is developed to consider the contributions of the normal velocity. The inclusion of the turbulence-induced normal velocity term is found to have a negligible effect on the mass transfer coefficient. The contribution wave-induced normal velocity can be classified on the dimensionless parameter V. If V above a critical value of V, $V_{crit}$, the effects of the wave-induced normal velocity become larger with an increase in V. IF V its effects negligible for V < $V_{crit}$. The unknown shear rate is numerically determined by solving the 2-D mass transport equation inversely. The president inverse method can predict the unknown shear rate more accurately in thin wavy flow with large amplitude waves than the previous method.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.27 no.10
• /
• pp.1661-1666
• /
• 2003

The purpose of this study is to develop the simplified model of the crankshaft in the large marine engine for dynamic analysis. Because the actual engine system is under complex dynamic loading condition and it has multi-cylinder, the dynamic analysis is purchased at a high computation cost. In spite of this burden, the dynamic analysis must be perfonned to assure structural integrity of operating marine engine. Therefore, simplification of the analytic model is necessary for dynamic analysis. Beam-mass model, which is generated with the section property method, is the model simplified effectively. Section property method can provide desired section information by optimization technique. By applying beam-mass model to the crankshaft in the large marine engine, the usefulness of the proposed method was proven.

• Journal of Advanced Marine Engineering and Technology
• /
• v.20 no.4
• /
• pp.101-107
• /
• 1996

This test was performed on the hydraulic automatic gauge control(AGC) system of adaptive mass flow method. Fundamental purpose of this study are performance evaluation of this AGC system under the actual rolling condition. It was concluded that the response of AGC system depends on the dynamic characteristics of a reel motor or roll position. The test results are as follows : 1) The control method of reel motor current is better than than of the roll position as AGC system. 2) The more steel strip thickness of delivery side is thick, the larger the gauge deviation is large, and the more it is thin, the larger the gauge deviation rate is large. 3) Because the gauge deviation is large at acceleration and deceleration speed than steady speed, so AGC system is better to adopt over 50m/min. By applying this AGC system, not only the accurary in strip thickness were improved but also productivity was improved dramatically.

• Wind and Structures
• /
• v.20 no.3
• /
• pp.363-388
• /
• 2015

For controlling the vibration of specific building structure with large span, a practical method for the design of MTMD was developed according to the characteristics of structures subjected to wind loads. Based on the model of analyzing wind-induced response of large-span structure with MTMD, the optimization method of multiple tuned mass dampers for large-span roof structures subjected to wind loads was established, in which the applicable requirements for strength and fatigue life of TMD spring were considered. According to the method, the controlled modes and placements of TMDs in MTMD were determined through the quantitative analysis on modal contribution to the wind-induced dynamic response of structure. To explore the characteristics of MTMD, the parametric analysis on the effects of mass ratio, damping ratio, central tuning frequency ratio and frequency range of MTMD, was performed in the study. Then the parameters of MTMD were optimized through genetic algorithm and the optimized MTMD showed good dynamic characteristics. The robustness of the optimized MTMD was also investigated.

• Proceedings of the Korean Nuclear Society Conference
• /
• 1996.05b
• /
• pp.227-232
• /
• 1996

The one-third calibrating relation by steady solution can cause large error when applied to an unsteady flow with large amplitude waves. Extended calibrating method, which can treat the normal convective contribution, is developed. The normal mass convective term is included into the 2-D mass transport equation by means of rms value and random function. The unknown shear rate is numerically determined by solving the 2-D mass transport equation inversely. This recovery method which predicts the unknown shear rate is constructed. It is found that it works very well without distortion. The inclusion of the normal convective term has a negligible effect on the mass transfer coefficient.

• Journal of computational fluids engineering
• /
• v.7 no.2
• /
• pp.8-16
• /
• 2002

A numerical study on the use of the momentum interpolation method for flows with a large body force is presented. The inherent problems of the momentum interpolation method are discussed first. The origins of problems of the momentum interpolation methods are the validity of linear assumptions employed for the evaluation of the cell-face velocities, the enforcement of mass conservation for the cell-centered velocities and the specification of pressure and pressure correction at the boundary. Numerical experiments are performed for a typical flow involving a large body force. The numerical results are compared with those by the staggered grid method. The fact that the momentum interpolation method may result in physically unrealistic solutions is demonstrated. Numerical experiments changing the numerical grid have shown that a simple way of removing the physically unrealistic solution is a proper grid refinement where there is a large pressure gradient. An effective way of specifying the pressure and pressure correction at the boundary by a local mass conservation near the boundary is proposed, and it is shown that this method can effectively remove the inherent problem of the specification of pressure and pressure correction at the boundary when one uses the momentum interpolation method.

• Journal of Surface Science and Engineering
• /
• v.27 no.4
• /
• pp.234-240
• /
• 1994

A large area impurity doping method for poly-Si TFT LCD has been developed. The advantage of this method is the doping of impurities into Si over a large area without mass separation and beam scanning. Phosphorus diluted in hydrogen was discharged by RF(13.56MHz) power and ions from discharged gas were accelerated by DC acceleration voltage and were implanted into deposited Si films. The annealing characteristic of this method was similar to that of the ion implantation method in the low doping concentration. Three mechanisms were evolved in the annealing characteristics of phosphorus doped Si films. Point defects annihilation and the retrogradation of dopant atoms at grain boundaries as a result of grain growth played a major role at low and high annealing temperature, respectively. However, due to the dopant segregation, the reverse annealing range existed at intermediate annealing temperature.

• Journal of Life Science
• /
• v.11 no.1
• /
• pp.19-23
• /
• 2001

To develop the effective microbial screening method, pyrolysis mass spectrometry (PyMS) fingerprinting was evaluated as a tool that discriminate various yeast strains. The target yeast strains were isolated from industrial wastewater. Seventeen environmental isolated yeast strains were examined by pyrolysis mass spectrometry and sequencing analysis of the large subunit rRNA gene D1/D2 region. The PyMS results were compared with those of sequencing analysis. Taxonomic correlations were observed between the PyMS data and the sequencing results. It was concluded that PyMS provides a rapid, reliable and cost-reducing method for discrimination of the yeast strains.