• Journal of the Korean Wood Science and Technology
• /
• 제51권4호
• /
• pp.239-252
• /
• 2023

In this study, bending and compression strength tests were performed to investigate effect of composition of layer layout of Larix cross-laminated timber (CLT) on mechanical properties. The Larix CLT consists of five laminae, and specimens were classified into four types according to grade and composition of layer. The layer's layout were composited as follows 1) cross-laminating layers in major and minor direction (Type A), and 2) cross-laminating external layer in major direction and internal layer applied grade of layer in minor direction (Type B). E12 and E16 were used as grades of lamina for major direction layer of Type A and external layer of Type B according to KS F 3020. In results of the bending test of CLT using same grade layer according to layer composition, the modulus of elasticity (MOE) of Type B was higher than Type A. In case of prediction of bending MOE of Larix CLT, the experimental MOE was higher than 1.00 to 1.09 times for Shear analogy method and 1.14 to 1.25 times for Gamma method. Therefore, it is recommended to predict the bending MOE for Larix CLT by shear analogy method. Compression strength of CLT in accordance with layer composition was measured to be 2% and 9% higher for Type A using E12 and E16 layers than Type B, respectively. In failure mode of Type A, progress direction of failure generated under compression load was confirmed to transfer from major layer to minor layer by rolling shear or bonding line failure due to the middle lamina in major direction.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 춘계학술대회 논문집
• /
• pp.67-70
• /
• 2007

LTCC (Low Temperature Co-fired Ceramic) has been emerged as a promising technology in packaging industry. In this technology the lamination and the sintering process are very important because they change the permittivity of ceramics and the dimension of metal pattern which have influences on electric property. In this paper we studied on influence of the permittivity and the dimension change by lamination pressure and sintering temperature of LTCC process. As a results, permittivity increase along with increasing of lamination pressure and sintering temperature.

• Fibers and Polymers
• /
• 제4권2호
• /
• pp.71-76
• /
• 2003

We evaluated the seam characteristics with finishing, seaming and sealing processes and seam Puckering behavior of the breathable waterproof fabrics with laser scan. There were differences in 99% significant level between the seamed fabric and the sealed fabric. Seam breakage was initiated with the breakage of sewing thread, so the seam strength after seaming was almost uniform. The sewn seam strength and elongation increased with sealing process in all finishing methods. Pucker grade of laminating type was generally much higher than that of the coating type. We confirmed that wave length and amplitude have more important meaning than the number of weave in the breathable waterproof fabrics. The puckering in breathable waterproof fabrics is mainly occurred by inherent and feeding pucker. The former if due to the insertion of sewing thread and the littler is caused by differential feeding when two pieces of fabric are fed into the gap between a press foot and needle plate.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 하계학술대회 논문집
• /
• pp.247-247
• /
• 2009

In this work, Ga-doped ZnO (GZO) thin films for toxic gas sensor application were deposited on low temperature co-fired ceramic (LTCC) substrates, by RF magnetron sputtering method. LTCC is one of promising materials for integration with heater, low cost production and high manufacturing yields than silicon substrate. The LTCC substrates with thickness of $400\;{\mu}m$ were fabricated by laminating 12 greentapes which consist of alumina and glass particle in an organic binder. The GZO thin films deposited on the substrates and were analyzed by X-ray diffraction method (XRD) and field emission scanning electron microscope (FESEM). The films are well crystallized in the hexagonal (wurzite) structure with increasing thickness. The fabricated sensors showed good sensitivity and fast response time to common types of toxic gases (NOx, COx).

• 한국세라믹학회지
• /
• 제28권6호
• /
• pp.483-487
• /
• 1991

Ferrite electromagnetic wave absorber whose attenuation ability are mainly relied on their magnetic loss, has been used in relatively narrow wave frequency ranges. In this study, we tried to produce a wide-range electromagnetic wave absorber by laminating sintered ferrite (Mn0.07Ni0.28Zn0.65Fe2O4) and dielectrics (Cordierite). We also investigated effects of dielectric constant and thickness on the attenuation behavior of the absorber. Applicable band width, in which the attenuation is greater than 20 dB can be widened from 100∼700 MHz of ferrite alone to 100∼900MHz by employing the laminated structure. Thickness of dielectrics to achieve wide-range application decreased as the dielectric constant increased.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2005년도 춘계학술발표대회 논문집
• /
• pp.67-70
• /
• 2005

The carbon fiber reinforced/epoxy laminated composites were fabricated with initial fiber failures within the unidirectional fiber pre-pregnated ply. The fiber failures were made intentionally either parallel to and/or perpendicular to the unidirectional fibers within the ply. The pre-made clear-cut cracks were found to be healed partially after laminating process. The laminates were impacted with or without initial fiber failures within the laminates. The force versus deflection curves were compared. The partially healed laminates showed the reduced laminate stiffness as compared to those without any intentional fiber failures. The impact curves were compared with size and the location of the initial failures varied.

• 한국자동차공학회논문집
• /
• 제25권3호
• /
• pp.267-272
• /
• 2017

Automotive seat covers with olefin film imported from foreign companies exhibit some problems such as low peeling strength and high burning rate. The traditional manufacturing process requires gas flame or direct heating for the laminating step. This paper introduces an alternative solution that replaces the olefin film and flame lamination method in making automotive seat covers or interior fabrics. We adopt a new manufacturing concept that applies a water-based resin coating to develop a coating system. The coating machine was successfully developed and tested. Results are intended to contribute to improving the quality and productivity of automotive seat cover production.

• 센서학회지
• /
• 제15권5호
• /
• pp.352-356
• /
• 2006

In this paper, we developed enzyme electrode of a new form to improve performance of disposable glucose sensor. We could fabricate electrode of Cu/Ni/Au structure which has very low electrical resistance (0.1 $\Omega$) by sticking copper film to plastic film with laminating method and electro-plated nickle and gold on it. The enzyme electrode was completed by immobilizing enzyme on the fabricated electrode. The fabricated glucose sensor has very quick sensing time as 3 seconds, and excellent reproducibility, fabrication yield as well.

• 접착 및 계면
• /
• 제7권4호
• /
• pp.53-59
• /
• 2006

The paper highlights technical advances and introduces recent innovations such as smart curing laminating adhesives for flexible packaging with low migration rates of aromatic isocyanates and amines. Latent reactive one-part systems on the basis of surface deactivated solid isocyanates open up new dimensions for heat setting adhesives and waterborne PU dispersions. The new generation of Purmelt Micro Emission adhesives contains less than 0.1% of MDI monomer, thereby drastically reducing the emission of hazardous isocyanate vapors during processing and setting a significantly improved technical standard in occupational safety. Once again, polyurethane adhesives have demonstrated their unique ability to adapt to new process, product, safety and environmental requirements.

• 설비공학논문집
• /
• 제19권10호
• /
• pp.735-741
• /
• 2007

An axial F.R.P. fan model for cooling tower is developed. The fan is designed using the equations for one dimensional inviscid flow through the fan blade. Fan shape is swept forward with a parabolic function. Calculations of the three dimensional turbulent flow around the fan are carried out to investigate performance of the fan. Data of the total pressure rise and hydraulic efficiency can be obtained for the various setting angles. Calculated values of the total pressure rise and hydraulic efficiency at the design point are less than those of the design specification. The prototype of the F.R.P. fan is made by laminating of the fiberglass and epoxy resins on the mold of fan shape.