• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2006년도 하계종합학술대회
• /
• pp.597-598
• /
• 2006

This paper describes a development of a new $1.4{\times}1.1$ and $2.0{\times}1.4mm$ RF SAW filters made by PCB substrate instead of HTCC package, and this technology can reduce the cost of materials down to 40%. We have investigated the multi-layered PCB substrate structures and raw materials to find out the optimal flip-bonding condition between the $LiTaO_3$ wafer and PCB substrates. Also the optimal materials and processing conditions of epoxy laminating film were found out through the experiments which can reduce the bending moment caused by the difference of the thermal expansion between the PCB substrate and laminating film. The new PCB SAW filter shows good electrical and reliability performances with respect to the present SAW filters.

• 한국공간구조학회논문집
• /
• 제13권4호
• /
• pp.41-47
• /
• 2013

For the artistic column used by Glass Fiber Reinforced Plastic(GFRP), the connection of steel with GFRP were needed. Due to the fabricating characteristics of hand laminating, GFRP surfaces had to be connected. Because there were no existed data of these connection, experimental study has to be followed so that the structural strength and buckling mode could be investigated. In this paper, therefore, the axial tests of steel with GFRP were performed. The connection of GFRP's surfaces could be also tested as well. As a result, it could be figured out that the strength of these connections were determined by the adhesive strength.

• 반도체디스플레이기술학회지
• /
• 제18권4호
• /
• pp.124-128
• /
• 2019

In this paper, a high temperature plastic film type water level sensor was developed. The high temperature film type water level sensor was manufactured by attaching a copper film to a polyimide film which can be used for a long time at 250℃, by laminating process and patterning the electrode by etching process. For the performance evaluation of the developed film type water level sensor, the temperature dependence of the capacitance was measured, and the deformation was examined after standing for 8 hours in 150℃ air. The developed film type water level sensor can be used at up to 150℃, and can be applied to electric ports and steam devices.

• 한국염색가공학회:학술대회논문집
• /
• 한국염색가공학회 2009년도 제41차 학술발표회
• /
• pp.159-160
• /
• 2009

• 한국세라믹학회지
• /
• 제45권9호
• /
• pp.561-566
• /
• 2008

Carbon fiber fabric-silicon carbide composites were fabricated by liquid silicon infiltration (LSI) process. The porous two-dimensional carbon fiber fabric performs were prepared by 13 plies of 2D-plain-weave fabric in a three laminating method, [0/90], [${\pm}45$], [$0/90/{\pm}45$] lay-up, respectively. Before laminating, a thin pyrolytic carbon (PyC) layer deposited on the surface of 2D-plain weave fabric sheets as interfacial layer with $C_3H_8$ and $N_2$ gas at $900^{\circ}C$. A densification of the preforms for $C_f-Si-SiC$ matrix composite was achieved according to the LSI process at $1650^{\circ}C$ for 30 min. in vacuum atmosphere. The bending strength of the each composite were measured and the microstructural consideration was performed by a FE-SEM.

• 접착 및 계면
• /
• 제7권3호
• /
• pp.16-25
• /
• 2006

내열성 및 투습방수기능을 가진 신발용 직물 및 부직포를 제조하기 위하여 스크린 방식으로 공정조건을 검토하고 투습방수 필름을 라미네이팅 한 후, 최종제품의 물성을 평가하였다. 결과는 다음과 같다. 열가소성 핫 멜트와는 달리 반응형 폴리우레탄 핫 멜트는 작업 이후에 적정한 내열성을 보유하는 것으로 나타났다. 최적의 용융접착 공정조건은 다음과 같다 ; 드럼 온도 $95^{\circ}C$, 호스 온도 $97^{\circ}C$, 공급파이프 온도 $100^{\circ}C$, 스크린 온도 $105^{\circ}C$이고, opposite roller의 압력은 $1kgf/cm^2$, laminating roller의 압력은 $3kgf/cm^2$이며, 가공속도는 15 m/min이다. 투습도는 필름의 두께가 증가함에 따라 투습도는 감소하였으나, 내수도는 증가하였고, 공기투과도는 필름의 영향이 지배적이었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.396-400
• /
• 2003

A new synthesis process for nano laminating Ti$_3$SiC$_2$ has been developed using TiCx (x=0.67) and Si powder as starting materials by a reaction hot pressing. Bulk Ti$_3$SiC$_2$ was fabricated using a green body consisting of TiCx and Si by a hot pressing under the pressures of 25 MPa at 1420-1550 $^{\circ}C$ for 90 min. The synthesized Ti$_3$SiC$_2$ was consisting of only TiCx and Ti$_3$SiC$_2$. The relative density of sintered bulk Ti$_3$SiC$_2$ was increased as the hot pressing temperature was increased, which was mainly due to the increase in TiCx contents in synthesized Ti$_3$SiC$_2$. The synthesized Ti$_3$SiC$_2$ bulk was consisted of nano sized lamella structure of 20-100 nm in thickness. It was found that TiCx particles in Ti$_3$SiC$_2$ would increase the 3-point bending strength of synthesized Ti$_3$SiC$_2$ bulk. The maximum 3-P. bending strength of synthesized Ti$_3$SiC$_2$ bulk was more than 800 MPa. The Vickers hardness of synthesized Ti$_3$SiC$_2$bulk was as low as 5 Gpa, which was decreased with the indentation load. The quasi-plastic deformation behaviors were observed around indentation mark on Ti$_3$SiC$_2$.

• 펄프종이기술
• /
• 제33권4호
• /
• pp.15-20
• /
• 2001

The function of the moisture-proof paper is to prevent moisture from adsorbing into the packed goods. Water-vapor transmission rate of the moisture-proof paper should be less than 100g/$m^2$.24hr and the optimum rate would be less than 50g/$m^2$.24hr. In general the moisture-proof paper has been made by laminating polyethylene or polypropylene on top of the base paper. However this kind of moisture-proof paper has a problem in recycling so that it brings about environmental pollution. In general the moisture-proof paper has been made by laminating polyethylene or polypropylene on top of the base paper. However this kind of moisture-proof paper has a problem in recycling so that it brings about environmental pollution. The purpose of this paper was to make moisture-proof paper using the mixture of SB latex and wax emulsion which was recyclable and environmentally friendly. Water vapor transmission rate showed less than 50g/$m^2$.24hr in mixture ratio of 85:15, 87:13, 90:10. Especially the mixture ratio of 87:13 showed the most favorable water-vapor transmission rate. However, the moisture-proof layer was destroyed slightly by folding in packing. It has been observed that there was no close relationship between water-vapor transmission rate of the moisture-proof paper and grammage of the base paper, but the density of base paper had influenced on water vapor transmission rate. It was also observed that the moisture-proof paper could be recycled. The moisture-proof paper was similar to base paper in degree of the pulping, and there was no significant difference in dispersion between moisture-proof paper and base paper. Most of wax particles which caused the spots during drying process could be removed by flotation process. Tensile strength and tear strength of both moisture-proof paper and base paper after pulping were measured to examine the fiber bonding, and no significant difference in physical properties was observed.

• 한국구조물진단유지관리공학회 논문집
• /
• 제17권6호
• /
• pp.145-152
• /
• 2013

콘크리트는 대표적인 건설재료로서 지난 19세기 후반 이후 각종 구조물의 축조에 활용되고 있다. 콘크리트는 일반적으로 적절한 설계 및 시공 규정을 준수한다면 내구성을 확보하는 것으로 인식되었으나, 구조물의 사용 과정 중에 겪게 되는 각 종 외적 작용으로 인해 수명단축 및 성능저하 현상이 빈번히 나타나고 있으며 더욱이 노후화에 따른 콘크리트 구조물의 성능 저하는 억제할 수 없으며 결국 콘크리트 구조물의 유지관리 측면에서 보수 및 보강은 필요한 실정이다. 본 연구에서는 기존의 보수 및 보강공법의 성능을 개선하고자 콘크리트 표면의 강화 및 특히 내화학 성능의 향상을 위하여 개발되어진 내화학성적층보강공법 (Chemical Resistance of Laminating Reinforcement Method : CRM)을 적용하였다. 따라서 본 연구에서는 콘크리트 시험체에 대한 다양한 내구성 시험을 통하여 일반적인 보수 및 보강공법을 적용한 시험체 와의 비교분석을 통하여 결과를 도출하였으며 시험결과, 기존 보수 및 보강공법보다 CRM을 적용한 콘크리트 시험체의 내구성능이 향상되었는데 이는 에폭시계의 내산섬유보강 및 2중의 섬유계의 보강시트로 인한 적층효과로 판단된다.

• 프린팅코리아
• /
• 제12권1호
• /
• pp.108-109
• /
• 2013

(주)GMP(대표이사 김양평)는 지난해 11월 26일부터 30일까지 5일간 경기도 파주 본사에서 세계 45개국 52명의 해외 고객사 CEO 초청 'GMP International Laminating & Digital Finishing Seminar 2012' 를 김양평 회장의 주재로 개최하고, GMP의 신기술 및 신제품 소개와 향후 제품 전략을 제시했다.