• 한국분말재료학회지
• /
• 제23권3호
• /
• pp.207-212
• /
• 2016

In this study, Fe-Cu-Ni-Mo-C low alloy steel powder is consolidated by spark plasma sintering (SPS) process. The internal structure and the surface fracture behavior are studied using field-emission scanning electron microscopy and optical microscopy techniques. The bulk samples are polished and etched in order to observe the internal structure. The sample sintered at $900^{\circ}C$ with holding time of 10 minutes achieves nearly full density of 98.9% while the density of the as-received conventionally sintered product is 90.3%. The fracture microstructures indicate that the sample prepared at $900^{\circ}C$ by the SPS process is hard to break out because of the presence of both grain boundaries and internal particle fractures. Moreover, the lamellar pearlite structure is also observed in this sample. The samples sintered at 1000 and $1100^{\circ}C$ exhibit a large number of tiny particles and pores due to the melting of Cu and aggregation of the alloy elements during the SPS process. The highest hardness value of 296.52 HV is observed for the sample sintered at $900^{\circ}C$ with holding time of 10 minutes.

• 한국군사과학기술학회지
• /
• 제20권2호
• /
• pp.206-216
• /
• 2017

This paper studies on the dynamic properties of Ti-6Al-4V alloy. After forming the four different micro structures(equiaxed, lamellar, and 2 bimodals) through heat treatments, static and dynamic properties of each structure were investigated quantitatively. Dynamic behaviors of the alloy are observed by the compressive split Hopkinson pressure bar(SHPB) tests. In additon, parameters of Johnson-Cook equation were determined from the SHPB test results. In order to verify the suitability of the parameters, high velocity impact tests were performed and the results were compared with the numerical analysis results. Although the flow stress and the fracture strain of the bimodal structures were higher than those of the equiaxed structure at the static tests, the superior dynamic properties were observed at the equiaxed structure due to the effects of higher maximum flow stress and fracture strain. From the numerical analysis, J-C parameters which are determined on this study describe well the dynamic behavior of Ti-6Al-4V alloy. Experimental and analysis results are consistent with ${\pm}5%$ of an average error.

• Journal of Photoscience
• /
• 제9권2호
• /
• pp.284-286
• /
• 2002

The inverted retina of the Onchidium dorsal eye (DE) is composed only of ciliary-type photoreceptor cells (CC's). The outer segment (OS) of the CC is a concentric lamellar structure consisting of many modified ciliary membranes and stains positively with anti-$\beta$-tubulin antibody. Near the base of the OS there are about 30 basal bodies each connecting individually to a cilium. The cilia are rod-shaped at the base, progressing upwards to a flattened sheet-like shape with increasing surface area. Three-dimensional analysis on serial sections demonstrates the ladle-shape of a modified cilium. Many modified cilia wrap around each other like the leaves of a cabbage. Nine pairs of microtubules (MT's) are located regularly in a ring at the base of the cilium, gradually losing their regular arrangement towards the periphery, where they separate into two subgroups that are contained within two swollen portions of a modified cilium. Within the CC of the Onchidium DE, MT's in the modified cilium exist as two poles extending longitudinally in a thin expanded ciliary membrane. This arrangement may support the photoreceptive OS and serve to maintain its structural integrity.

• Journal of Oral Medicine and Pain
• /
• 제8권1호
• /
• pp.33-41
• /
• 1983

The authors observed the ultrastructure of oral leukoplakia simplex of gingiva, buccal mucosa, tongue and alveolar ridge. For the purpose of clearly defining the lesions under investigation in this study, leukoplakias were cinsidered to be any white patches on the oral mucous membranes that could not be removed by rubbing and could not be classified clinically or microscopically as another diagnosable disease. The tissue to be examined were embedded in paraffin for light microscopic study. The tissue to be examined under the electronomicroscope were fixed in 2.5% glutaraldehyde in 0.1M cacodylate buffer and 1% osmic acid in 0.1M cacodylate buffer, dehydrated with guaded alchol, and treated with propylene oxide, and embedded in Epon.Ultrathin sections were obtained by LKB III ultrotome, stained with uranyl acetate/lead citrate, and examined with Corinth 500EM. The results were as follows : 1. Epithelium of leukoplakia consisted of stratum basale, stratum spinosum, stratum granulosum and stratum corneum. 2. There was hyperorthokerotosis or hyperparakeratosis. 3. Granular cells contained a lot number of membrane coating granule showing lamellar structure, clearing ot codensation, and a lot of keratohyaline granule varied in size. 4. An increased concentration of tonofilaments and an increased number of desmosomes were found in the stratum spinosum. 5. Basal lamina generally showed its continuity, but in some locatoins, its interreption and multiplication appeared.

• 한국생산제조학회지
• /
• 제6권2호
• /
• pp.58-66
• /
• 1997

Ti alloys, with the advantageous tensile strength/density ratio and the chemical stability, have been used widely in the aerospace and chemical engineering industries and their usages are still expanding in various industrial areas. In the automotive industry, because of their superior merits of weight reduction and fuel saving, Ti alloys are expected to be used as various part materials including connecting rods, engine valves, springs and retainers, which are all subjected to the fatigue loads. In this study, using Ti-3A1-2.5V, the effects of temperature and microstructure change on fatigue crack propagation has been investigated. Five different microstructures were tested at the temperatures of room temperature, 20$0^{\circ}C$, 30$0^{\circ}C$ and 40$0^{\circ}C$ under the same frequency 20Hz. Some of the conclusions obtained are as follows: (1)Microstructurally, the morphology of less $\alpha$-phase and finer lamellar structure of $\alpha$ and $\beta$-Ti showed better registance to the fatigue crack propagation. (2)Fatigue crack growth rate increased with test temperature.

• 한국분말재료학회지
• /
• 제10권1호
• /
• pp.15-20
• /
• 2003

Hybrid $A1_2O_3-TiC$ ceramic particle reinforced 6061 and 5083 Al composite powders were prepared by the combination of twin rolling and stone mill crushing process, followed by consolidating processes of cold compaction, degassing and hot extrusion. The composite bar consists of lamellar structure of ceramic particle rich area and matrix area, in which the hybrid was decomposed into each TiC of about $3-4\mutextrm{m}$ and $AI_2O_3$ particles of about $1-2\mutextrm{m}$ in diameter. It also found that fine $Mg_2Si$ precipitates of about 30 nm were embedded in the matrix, which have grains of about 3 $\mutextrm{m}$. Higher UTS was measured at the 5083 composite bar compared to the conventionally fabricated composite, due to again refinement effect by the rapid solidification. No particle was shown to form in the interface between the matrix and reinforcement, whereas carbon was diffused into the matrix.

• 대한화장품학회:학술대회논문집
• /
• 대한화장품학회 2003년도 IFSCC Conference Proceeding Book I
• /
• pp.61-72
• /
• 2003

In cosmetic area, retinol is prominent ingredient for anti-wrinkle but unstable against light, heat, oxygen and so on. Therefore the stabilization of retinol is required. Here, we capsulated doubly retinol in the SLM(Skin Lipid Matrix) that makes three dimensional lamellar structure similar to skin, after formation of primary liposome (retinol-nanoemulsion). First, we make primary liposome from retinol / hydrogenated lecithin / polysorbate20 / caprylic ＆ capric triglyceride / ethanol / and so on, and the mean diameter to 70 nm, using microfluidizer passed three times at 800 Bar, repeatedly. Then we produce DC-liposome (doubly capsulated-liposome) that was encapsulated primary liposome with SLM made of hydrogenated phosphatidyl choline / caprylic ＆ capric triglyceride / 1, 3-butylene glycol / ceramide3 / cholesterol /etc. We measured for color stability against light and heat with chromameter. As a result of this experiment, we observed DC-liposome was more than from 1.5 to 3 times as stable as general liposome. Livability of retinol has improved from 2 to 6 times when we analyzed it by HPLC. Also, penetration effect of DC-liposome has improved.

• 대한기계학회논문집A
• /
• 제29권4호
• /
• pp.584-590
• /
• 2005

The effect of microstructure on mechanical behavior for Ti-6Al-4V alloy was studied. Two different kinds of specimens are prepared using heat treatments (rolled plate, $1050^{\circ}C)$ in order to Produce different microstructures. Various kinds of mechanical tests such as hardness, tensile, fatigue and fretting fatigue tests are performed for evaluation of mechanical properties with the changes of microstructures. Through these tests, the following conclusions are observed: 1) Microstructures are observed as equiaxed and $widmanst{\ddot{a}}ten$ microstructures respectively. 2) Impact absorbed energy is superior for the equiaxed microstructure, and the hardness and tensile strength are superior for the $widmanst{\ddot{a}}ten$ microstructure. 3) The fatigue endurance of $widmanst{\ddot{a}}ten$ microstritcture shows higher value than that of the equiaxed microstructure. 4) The fatigue endurance in fretting condition was reduced about $50{\%}$ from that of the non-fretting condition.

• 한국주조공학회지
• /
• 제8권4호
• /
• pp.437-445
• /
• 1988

The effect of interlamellar spacing on microstructural stability at high temperature was studied for unidirectionally solidified ternary $Ni\;/\;Ni_3Al-Ni_3$ Nb and binary $Ni-Ni_3Nb$ eutectic composite. The interlamellar spacing of both alloy systems were varied with the growth rate according to $"{\lambda}^2R=constant"$ relationship. As a result of isothermal heat treatments at high temperature it was considered that coarsening of lamellar structure was due to concentration gradient between the tip with a relatively small radius of curvature and the side of the thick lamellae with a larger radius of the opposite sign. Fault density was increased as the interlamellar spacing decreased. Therefore it is also considered that the higher coarsening rate of the specimen with the smaller interlamellar spacing was due to higher fault density. And the diference of coarsening rate between $Ni\;/\;Ni_3Al-Ni_3Nb$ and $Ni-Ni_3Nb$ eutectic composites was not observed when the interlamellar spacing was similar in size. This means that the presence of ${\gamma}'$ in ${\gamma}\;/\;{\gamma}'\;-{\delta}$ eutectic had no b arrier effect to diffusion through the ${\gamma}$ matrix.

• Macromolecular Research
• /
• 제14권6호
• /
• pp.640-645
• /
• 2006

Polyethylene of bimodal molecular weight distribution was irradiated with an electron beam. The thermal and mechanical properties were examined by DSC, small and wide angle X-ray scattering and static tensile test according to the crystal morphology of the irradiated samples. The crystal morphology change upon irradiation, as revealed by wide angle X-ray scattering, correlated well with the changes in melting enthalpy, whereas the lamellar thickness and the amorphous gap thickness remained virtually unchanged at irradiation doses up to 500 kGy. Crosslinks in the crystal domains became evident at an energy level of 250 kGy, resulting in reduced crystallinity and crystal size of the (110) and (200) planes. The samples became stiff and brittle with increased irradiation dose, which seem to be more relevant to the amount of cross links than the crystal morphology changes.