• Journal of the Korean Wood Science and Technology
• /
• v.46 no.1
• /
• pp.10-16
• /
• 2018

Lindera erythrocarpa is a less utilized species in Korea although that it has straight stem and it grows up to 40 cm in diameter. A proper kiln-dry schedule is required in advance to utilize an unknown species. Terazwa's quick oven-dry method was used to find it and which was confirmed by drying 25 mm thick boards in a kiln. The average green moisture content and the average green specific gravity of Lindera erythrocarpa are 72.3% and 0.53, respectively. Prospective kiln-drying conditions obtained by Terazwa's quick oven-dry method are a initial dry-bulb temperature of $50^{\circ}C$, a initial wet-bulb depression of $4^{\circ}C$ and a final dry-bulb temperature of $75^{\circ}C$, which are in a good agreement with USDA FPL kiln-dry schedule of T5-D4. 25 mm thick boards dried in a kiln with T5-D4 kiln-dry schedule did not have any severe drying defects such as honycombing and warping. A severer kiln-dry schedule of T8-C5 was developed and applied to another kiln-drying run to confirm it.

• Journal of the Korea Furniture Society
• /
• v.11 no.1
• /
• pp.69-74
• /
• 2000

Pinus $rigida{\times}taeda$ and Liriodendron tulipifira have been planted in this country for about 20 years. They are known as a relatively 13st-grown and useful species. The physical properties such as green moisture contents, specific gravities and dimensional shrinkages were examined with natively grown timbers. The kiln-dry schedules were developed with 30m thick boards by using an oven-fast-drying method. In both species the green MC's of sapwoods were higher than those of heartwoods, but their discrepancies were small. The green specific gravities of Pinus $rigida{\times}taeda$ and Liriodendron tulipifera were 0.48 and 0.41~O.42, respectively. The developed kiln-dry schedules were proven to minimize drying defects for the hoards of 30mm thickness and various width.

• Journal of the Korean Wood Science and Technology
• /
• v.31 no.6
• /
• pp.15-21
• /
• 2003

Image processing technique was adapted for exploring the more convenient ways to investigate the drying characteristics of wood. The acquisition of information about drying characteristics is indispensable for the development or improvement of dry-kiln schedules. A small internal fan type wood dry kiln was combined with image-processing and data-acquisition systems to monitor continuously the formation of checks and moisture reduction during drying. All the images and data were analyzed to improve or estimate the dry-kiln schedules and predict the drying time which would be required to dry green wood to 10% moisture content in internal fan type kiln. Samples of 20 mm- and 50 mm-thick Metasequoia glyptostrobodies, Paulownia coreana Uyeki, Pinus densiflora Sieb. Et Zucc., Platanus occidentalis L., Quercus acutissima and Robinia pseudo-acacia were used to verify the potentiality of this technique.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.2
• /
• pp.113-119
• /
• 1987

A study was conducted to determine the kiln drying schedule for hydrid aspen, This kiln drying schedule was found by oven drying method and developed by pilot testing of 2.0cm, 2.5cm, 3.0cm-thick green lumber. The results of this study were as follows: 1. Kiln drying schedule developed by oven-drying method was $T_{12}-E_5$ for 2.5cm-thick green lumber. 2. Drying times for 2.0cm-thick green lumber(127.0 percent moisture content) to 7.3 percent moisture content, for 2.5cm-thick green lumber(95.0 percent moisture content) to 9.7 percent moisture content, and for 3.0cm-thick green lumber(118.5 percent moisture content) to 10.0 percent moisture content were 45 hours, 45 hours, and 54 hours, respectively. 3. Drying rate from 90 to 10 percent moisture content of 2.5cm-thick lumber was about 0.7 times faster than that of 2.0cm-thick lumber and about 1.1 times faster than that of 3.0em-thick lumber. 4. End checks for 2.0cm-, 2.5cm-, and 3.0cm-thick green lumber occurred 95, 74 and 100 percent moisture content, respectively and reached maximum amount in 53, 41, and 60 percent moisture content, respectively. 5. No surface check and no honeycomb occurred. 6. Cupping and collapse slightly occurred and the quality of dry lumber was first.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.1
• /
• pp.45-54
• /
• 1986

A study was conducted to determine the physical properties related to drying characteristics, the seasonal air drying curves and the kiln drying schedule for taun lumber imported and utilized. This kiln drying schedule was found by oven drying and developed by pilot testing of green lumber and partially air dried lumber. The results of this study were as follows; 1. Average green specific gravity and standard deviation of heartwood lumber were 0.60${\pm}$0.03 and those of sapwood lumber were 0.64${\pm}$0.02. 2. Radial shrinkage from green to air dry and from green to oven dry were 3.05 percent and 5.96 percent respectively, and tangential shrinkage from green to air dry and to oven dry were 5.49 percent and 8.74 percent respectively. 3. Drying time for 25mm thick green lumber (50 percent moisture content) air dried to 30 percent moisture content were 14 days in springtime. 6 days in summertime, and 12 days in autumntime, whereas for 50mm thick lumber in 36 days in springtime, 18 days in summertime, 38 days in autumntime. 4. Kiln drying schedules developed by oven drying were T8-B3 for 25mm thick lumber and T5-B2 for 50mm thick lumber. 5. Kiln drying curves of green 25mm and 50mm thick lumber were similar to those of partially air dried lumber from the level of 30 percent average moisture content. Green 25mm thick lumber (55.7 percent moisture content) was dried to 9.3 percent moisture content in 101.5 hours and green 50mm thick lumber (65.6 percent moisture content) was dried to 11.5 percent moisture content in 526 hours. 6. End checking for green 25mm thick lumber occured in 49.6 percent moisture content and reached maximum amount in 27.6 percent moisture content and closed in 15.8 percent moisture content. 7. End checking for green 50mm thick lumber and partially air dried lumber developed and reached maximum amount earlier then for 25mm thick lumber. 8. Final moisture content of surface layer for 50mm thick lumber was one half of that of core, and moisture content equalized in the lumber after nine days of room conditioning. 9. Casehardening for 50mm thick lumber was slight and was conditioned after nine days of room stroage. 10. Drying defects, such as end checking and surface checking, were not observed and the quality of dry lumber was first.

• Journal of the Korean Wood Science and Technology
• /
• v.15 no.2
• /
• pp.53-66
• /
• 1987

Korean red pine (Pinus densiflora S. et. Z.) and pitch pine(Pinus rigida Mill) $5{\times}10cm$ dimension lumber were dried in a kiln providing a cross-circulation velocity of 5 m/sec at dry-and wet-bulb temperatures of 116 and $71^{\circ}C$, followed by 3 hours at 91 and $85^{\circ}C$. Compared to dimension lumber dried lumber were as follows. 1. To dry to 10 percent moisture content, the high-temperatures schedule of Korean red pine and pitch pine lumber took less than one seventh the time required by the conventional kiln drying schedule. 2. High-temperature drying rate and conventional drying rate to 10 percent moisture content of Korean red pine lumber were 2.75 and 0.35%/hr, and those of pitch pine lumber were 3.38 and 0.46%/hr respectively. 3. Compared to lumber of both species on conventional schedule, moisture gradient of high-temperature lumber was greater. 4. Compared to lumber on conventional schedule, maximum surface checking of high-temperature lumber of both species was severer, and maximum end checking of high-temperature lumber of both species was similar to that of lumber on conventional schedule. 5. Compard to lumber on conventional schedule, Korean red pine lumber dried at high temperature showed more honeycombing, but pitch pine lumber dried at high-temperature showed significantly slighter honeycombing. 6. Compared to lumber on conventional schedule, the high-temperature lumber showed less warping lumber of both species. 7. Collapse and casehardening of Korean red pine and pitch pine lumber on both scheules were slight.

• Journal of the Korean Wood Science and Technology
• /
• v.17 no.3
• /
• pp.67-81
• /
• 1989

This experiment was carried out to know the mothod of changing the step of moisture content schedule with time in conventional kiln drying. For the purpose of this object. we made drying model by applying the moisture diffusion model by J.FSiau(1984) to average moisture content equation by J.Crank(1956) derived it from Fick's second law. And to verify this method of drying model. 2.5cm-thick boards and 5.0cm-thick dimension lumbers of Pinus densiflora were kiln-dried with the schedule of T11-C3 and T10-C4, respectively. And then the drying rates were investigated and compared with those calculated from drying model. The results obtained were as follows 1. Average drying rate and total drying time of board to dry to 6.5% moisture content were 0.64%/hr and 109hr., and those of dimension lumber to dry to 8.3% moisture content were 0.4%/hr. and 162hr., respectively. 2. The moisture content of shell and core decreased by equalizing treatment and increased by conditioning treatment both on board and dimension lumber. But the moisture gradient was lower after conditioning than after equalizing. 3. As the drying was proceeded, the transverse bound water diffusion coefficient all but linearly decreased, the water vapor diffusion coefficient abruptly curvilinearly increased, while the transverse diffusion coefficient curvilinearly decreased both on board and dimension lumber. But each of diffusion coefficients on board was larger than that on dimension lumber. 4. Compared to experimential drying rate of board. theoretical drying rate was larger at 30.0%-21.8% moisture content range and was similiar at 21.8%-5.4% moisture content. And in case of dimension lumber, the drying rate was similiar at 30.0%-16.1% moisture content range but theoretical drying rate was much lower at 16.1%-8.3% moisture content range. 5. The possibility of adapting this drying model to changing the moisture content schedule step with time was in the range of 21.8%-5.4% moisture content on board. And in the case of dimension lumber that was in the range of 30.0%-16.1% moisture content.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.3
• /
• pp.3-15
• /
• 1986

This study was carried out to investigate the drying rate and drying defects of Populus euramericana using the SDR (Saw-Dry-Rip) process. Flitches for SDR process were rough edged for compact kiln stacking, and then kiln-dried to 10 percent moisture content with dimensions in the same run, using the kiln-drying schedule ($T_8-F_4$) recommended by Rasmussen. The results obtained were as follows: 1. Drying rate of dimensions was slower than that of flitches. 2. Final moisture content and moisture distribution of dimensions were lower than those of flitches. 3. Average bowing, cupping, crooking, and twisting were reduced 20 percent, 25 percent, 54.9 percent, and 13.4 percent by SDR process respectively. 4. Bowing and cupping were more severe in dimensions from the area near the pith than in those from the area near the bark, and for crooking and twisting the reverse was true. 5. Surface checking of dimensions developed less than that of flitches and end checking of dimensions was similar to that of flitches. 6. Honeycomb, thickness shrinkage, and collapse of dimensions were similar to those of flitches. 7. The degree of casehardening of dimensions was higher than that of flitches.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.2
• /
• pp.3-13
• /
• 1985

This study was carried out to investigate the effects of presteaming on the drying rate and drying defects of 3 cm - thick Quercus acutissima. Specimens for presteaming were steamed green at $100^{\circ}C$ for 4 hours and then kiln-dried to 10 percent moisture, content with controls, using the kiln-drying schedule ($T_4-C_2$) recommended by Rasmussen. The results obtained were as follows: 1. Presteaming reduced drying time approximately 18 percent from 70 to 10 percent moisture content. 2. The effect of presteaming on surface checking was not significant. 3. Presteamed specimens showed the reduction in end checking compared with controls. 4. Percents of boards with collapse, cupping, and honeycomb of presteamed specimens were slightly lower than those of controls. 5. Dry lumber grade of presteamed specimens was better than that of controls. Percent of first grade boards of presteamed specimens was 20 percent higher than that of controls and percents of second and third grade boards of presteamed specimens were 15 and 5 percent lower than those of controls, respectively.