• Journal of Energy Engineering
• /
• v.2 no.3
• /
• pp.268-275
• /
• 1993

A series of parametric investigations are performed in order to resolve the flow characteristic of a Quebec city stoker incinerator. The parameters considered in this study are five internal configurations of the Quebec city stoker itself and its modified ones, primary air velocity, the injection velocity and angle of the secondary air, and the reduction of the stoker exit area. A control-volume based finite-difference method by Patankar together with the power-law scheme is employed for discretization. The resolution of the pressure-velocity coupling is made by the use of SIMPLEC algorithm. The standard, two equation, k-$\varepsilon$ model is incorporated for the closure of turbulence. The size of recirculation region, turbulent viscosity, the mass fraction of the secondary air and pressure drop are calculated in order to analyze the characteristics of flow field. The results are physically acceptable and discussed in detail. The flow field of the Quebec city stoker shows the strong recirculation zone together with the high turbulence intensity over the upper part of the incinerator.

• Journal of Korean Ophthalmic Optics Society
• /
• v.6 no.1
• /
• pp.111-117
• /
• 2001

The temperature dependence of dielectric constant and electrical conductivity for the BBPS glasses system was studied over a temperature range between $30^{\circ}C$ and $500^{\circ}C$ and at a frequency ranged from $10^3$ Hz to $10^7$ Hz. The dielectric constant ${\varepsilon}$ at room temperature of $xB_2O_3-yBi_2O_3-zPbO-5SiO_2 $ glasses was measured to be 15 at $10^5$ Hz for all samples and found to be almost frequency independent. At the relatively low temperature ranger (<$70^{\circ}C$), the dielectric constant was almost temperature independent and above that it increased with increasing temperature: the rate of increase being different at different frequencies. This behavior could be explained on the basis of the presence of molecular dipoles. The dielectric constant was found to depend on the composition as well as the crystalline phases formed in the glass matrix.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.1
• /
• pp.1-12
• /
• 1998

Industrial ejector system is a facility to transport, to compress or to pump out a low pressure secondary flow by using a high pressure primary flow. An advantage of the ejector system is in its geometrical simplicity, not having any moving part, compared with other fluid machinery. Most of the previous works have been performed experimentally and analytically. The obtained data. are too insufficient to improve our current understanding on the detailed flow field inside the ejector. In order to provide more comprehensive data on this ejector flow field, two-dimensional computations using Reynolds-averaged Navier-Stokes equations were performed for a very wide range of operating pressure ratio of the supersonic ejector with a secondary throat. The current results showed that the supersonic ejector system has an optimum pressure ratio for the secondary flow total pressure to be minimized. The numerical results clearly revealed the shock system, shock/boundary layer interaction, and secondary flow entrainment inside the supersonic ejector.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.6 no.2
• /
• pp.12-20
• /
• 1998

Exter ballistics of a typical high-speed projectile is studied through a flow-visualization experiment and an unstructured grid Navier-Srokes computation. Experiment produced a schlieren photograph that adequately shows the characteristic features of this complex flow, namely two kinds of oblique cone shocks and turbulent wake developing into the downstream. A hybrid scheme of finite volume-element method is used to simulate the compressible Reynolds-Averaged Navier-Stok- es solution on unstructured grids. Osher's approximate Riemann solver is used to discretize the cinvection term. Higher-order spatial accuracy is obtained by MUSCL extension and van Albada ty- pe flux limiter is used to stabilize the numerical oscillation near the solution discontinuity. Accurate Gakerkin method is used to discretize the viscous term. Explict fourth-order Runge-Kutta method is used for the time-stepping, which simplifies the application of MUSCL extension. A two-layer k-$\varepsilon$ turbulence model is used to simulate the turbulent wakes accurately. Axisymmetric folw and two-dimensional flow with an angle of attack have been computed. Grid-dependency is also checked by carrying out the computation with doubled meshes. 2-D calculation shows that effect of angle of attack on the flow field is negligible. Axi-symmetric results of the computation agrees well with the flow visualization. Primary oblique shock is represented within 2-3 meshes in numerical results, and the varicose mode of the vortex shedding is clearly captured in the turbulent wake region.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.32 no.7
• /
• pp.549-557
• /
• 2008

Despite of the laminar-turbulent transition region co-exist with fully turbulence region around the leading edge of an airfoil, still lots of researchers apply to fully turbulence models to predict aerodynamic characteristics. It is well known that fully turbulent model such as standard k-model couldn't predict the complex stall and the separation behavior on an airfoil accurately, it usually leads to over prediction of the aerodynamic characteristics such as lift and drag forces. So, we apply correlation based transition model to predict aerodynamic performance of the NREL (National Renewable Energy Laboratory) Phase IV wind turbine. And also, compare the computed results from transition model with experimental measurement and fully turbulence results. Results are presented for a range of wind speed, for a NREL Phase IV wind turbine rotor. Low speed shaft torque, power, root bending moment, aerodynamic coefficients of 2D airfoil and several flow field figures results included in this study. As a result, the low speed shaft torque predicted by transitional turbulence model is very good agree with the experimental measurement in whole operating conditions but fully turbulent model(${\kappa}-\;{\varepsilon}$) over predict the shaft torque after 7m/s. Root bending moment is also good agreement between the prediction and experiments for most of the operating conditions, especially with the transition model.

• Proceedings of the KSME Conference
• /
• 2001.11b
• /
• pp.499-504
• /
• 2001

A validation of a 3D CFD model for predicting local subcooling of moderator in the vicinity of calandria tubes in a CANDU reactor is performed. The small scale moderator experiments performed at Sheridan Park Experimental Laboratory(SPEL) in Ontario, Canada[1] is used for the validation. Also a comparison is made between previous CFD analyses based on 2DMOTH and PHOENICS, and the current model analysis for the same SPEL experiment. For the current model, a set of grid structures for the same geometry as the experimental test section is generated and the momentum, heat and continuity equations are solved by CFX-4.3, a CFD code developed by AEA technology. The matrix of calandria tubes is simplified by the porous media approach. The standard $k-\varepsilon$ turbulence model associated with logarithmic wall treatment and SIMPLEC algorithm on the body fitted grid are used and buoyancy effects are accounted for by the Boussinesq approximation. For the test conditions simulated in this study, the flow pattern identified is a buoyancy-dominated flow, which is generated by the interaction between the dominant buoyancy force by heating and inertial momentum forces by the inlet jets. As a result, the current CFD moderator analysis model predicts the moderator temperature reasonably, and the maximum error against the experimental data is kept at less than $2.0^{\circ}C$ over the whole domain. The simulated velocity field matches with the visualization of SPEL experiments quite well.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.2
• /
• pp.251-257
• /
• 2012

Human body communication means transmitting and receiving data through human body medium or through free space along with the human body skin. Electric field distribution around the human body between the transmitter and the receiver were calculated at five different frequencies with 5 MHz interval between 10 MHz and 30 MHz. Commercial electromagnetic simulation tool was used for the calculation of E-field distributions applying the Korean standard male model including 29 different kinds of human tissues. After calculating specific absorption rate(SAR) values on back of the hand, it was compared with International Commission on Non-Ionizing Radiation Protection(ICNIRP) human protection guideline. While conductivities(${\sigma}$) and relative permittivities(${\varepsilon}_r$) of the human tissues for each frequency were input as the analyzing parameters, electric field intensities near both hands were integrated along the integral line between the nearby electrodes for the calculation of the transmitting and receiving voltages whose ratio was defined as channel loss. The calculated channel losses were about ($75{\pm}1$) dB and showed nearly flat response all through the evaluated frequencies.

• Journal of The Korean Society of Grassland and Forage Science
• /
• v.21 no.2
• /
• pp.67-74
• /
• 2001

A field experiment was carried out to determine the effects of chemical/mechanical treatments at mowing on the field drying rate and hay quality of alfalfa(Medicago sativa L., cv. Vernal) and spring oats(Avena satvia L., cv. Swan). The chemical drying agent of 2% $K_2CO_3$, mechanical mower conditioning, and no treatment(control) were treated for hastening hay-making in the spring of 1997. The forages were harvested at early bloom stage in alfalfa and heading stage in oats. After field dry, square bales were made by hay baler, and the dry matter(DM) loss, visual estimation and nutritive value of hay were evaluated after storing two months. The field drying rates of alfalfa and oats were high at mechanical treatment, but the drying effectiveness of chemical agents alone was very low. With mower conditioning, the duration of field dry was shortened by 1 day compared with control. therefore, mower conditioning enhance the field drying rate of alfalfa and oats. The DM loss of alfalfa and oats hay was reduced by mechanical treatment, but the efficiency by chemical alone was low. The visual score(leafiness, green color, odor and softness) of hay at mechanical treatment was slightly higher than that of chemical and control. The nutritive value(ADF, NDF, in vitro digestibility, and relative feed value) of hay was also high with treatment of mechanical, but those of chemical alone were similar compared with control. The nutritive value of hay after two months in both alfalfa and oats was decreased when compared with at harvest.