• 대한기계학회논문집B
• /
• 제25권6호
• /
• pp.799-803
• /
• 2001

Miniature heat pipe(MHP) with woven-wired wick was used to cool the CPU of a notebook PC. The pipe with circular cross-section was pressed and bent for packaging the MHP into a notebook PC with very limited compact packaging space. A cross-sectional area of the pipe is reduced about 30% as the MHP with 4mm diameter is pressed to 2mm thickness. In the present study a performance test has been performed in order to review varying of operating performance according to pressed thickness variation and heat dissipation capacity of MHP cooling module that is packaged on a notebook PC. New wick type was considered for overcoming low heat transfer limit when MHP is pressed to thin-plate. The limiting thickness or pressing is shown to be within the range of 2mm∼2.5mm through the performance test with varying the pressing thickness. When the wall thickness of 0.4mm is reduced to 0.25mm for minimizing conductive thermal resistance through the wall of heat pipe, heat transfer limit and thermal resistance of MHP were improved about 10%. In the meantime, it is shown that the thermal resistance and heat transfer limit for the MHP with central wick type are higher than those of MHP with existing wick types. The results of performance test for MHP cooling modules with woven-wired wick to cool a notebook PC shows the stability as cooling system since T(sub)j(Temperature of Processor Junction) satisfy a demand condition of 0∼100$\^{C}$ under 11.5W of CPU heat.

• 한국자기학회지
• /
• 제13권3호
• /
• pp.91-96
• /
• 2003

본 연구에서는 DC 마그네트론 스퍼터를 사용하여 Cr/Co/Al-Ox/Co/Ni-Fe 다층박막에 다양한 두께의 Cr 하지층을 삽입함에 따른 자기적 특성 및 전기적 특성에 관하여 연구하였다. 3 nm 두께의 Cr 하지층 증착시 자기저항비의 변화는 관찰할 수 없었고 적정한 Cr두께가 증가함에 따라 Co의 보자력이 크게 증가되었다 또한, 산화시간이 길수록 두 강자성층간에 보자력 차이 및 절연층의 저항이 점차 증가하였는데, 이는 산화시간에 따라 상부층 계면의 평탄성의 증가에 기인하는 것으로 생각되며 TEM을 통하여 확인할 수 있었다. Cr 하지층 유무에 관계없이 최고 자기저항비가 나타나는 절연층의 산화시간은 60~70초로 비슷하였지만 Cr 두께가 증가할수록 자기저항비는 감소하였다. 이는 전극간 계면의 거칠기의 증가로 인해 미반응 Al의 잔존 확률이 상대적으로 커짐에 따라 터널 전자의 산란이 증가함으로써 나타나는 것으로 생각된다. 이러한 결과로 Cr하지층의 두께는 3 nm로 고정하였으며 하지층의 증착 및 적정산화를 통하여 두 강자성층간에 큰 보자력 차이를 유도할 수 있었다. 이는 재현성에 있어서 가장 큰 문제점을 지닌 TMR 소자에 매우 긍정적인 해결방안을 제시할 수 있게 된다.̄

• Progress in Superconductivity
• /
• 제7권1호
• /
• pp.6-10
• /
• 2005

We have studied feasibility of single-layer second-order $high-T_c$ SQUID gradiometers in magnetocardiography. We have measured human cardiomagnetic signals using a short-baseline (5.8 mm) single-layer second-order YBCO gradiometer in partially shielded environments. The gradiometer has an overall size of $17.6\;mm{\times}6\;mm$ and contains three parallel-connected pickup coils which are directly coupled to a step-edge junction SQUID. The gradiometer showed an unshielded gradient noise of $0.84\;pT/cm^2/Hz^{1/2}$ at 1 Hz, which corresponds to an equivalent field noise of $280\;fT/Hz^{1/2}$. The balancing factor was $10^3$. Based on the same design rules as the short-baseline devices, we have studied fabrication of 30 mm-long baseline gradiometers. The devices had an overall size of $70.2\;mm{\times}10.6\;mm$ with each pickup coil of $10\;mm{\times}10\;mm$ in outer size. As Josephson elements we made two types of submicron bridges, which are variable thickness bridge (VTB) and constant thickness bridge (CTB), from $3\;{\mu}m-wide$ and 300 nm-thick YBCO lines with a thin layer of Au on top by using a focused ion beam (FIB) patterning method. VTB was 300 nm wide, 200 nm thick, 30 nm long with Au removed and CTB 100 nm wide and 30 nm long. In temperature-dependent critical currents, $I_c(T)$, VTB showed an nonmetallic barrier-type behavior and CTB an SNS behavior. We believe that those characteristics are ascribed to naturally formed grain boundaries crossing the bridges.

• 대한전자공학회논문지TC
• /
• 제49권1호
• /
• pp.47-52
• /
• 2012

전력증폭기는 기지국의 효율을 결정하는 중요한 요소이며, 효율성 제고를 위하여 GaN증폭소자를 사용한 Doherty 전력증폭기 구조에 대한 연구가 지속되고 있다. Doherty 전력증폭기의 메모리 효과는 선형성과 효율특성과 연관된 동작특성에 큰 영향을 미친다. 본 논문에서는 GaN Doherty 전력증폭기의 전열적인 비선형성 모델링과 전열적 메모리 효과가 GaN Doherty 증폭기의 왜곡형성과 보상에 대하여 연구하였다. GaN Doherty 증폭기의 전열적 메모리 특성을 모델링하기 위하여 순시적으로 소모되는 전력과 순시 접합온도의 정확한 관계식을 정립하였다. 제안된 모델의 파라미터로부터 GaN Doherty 전력증폭기의 비선형왜곡과 전열적 메모리 효과를 보상할 수 있는 전치왜곡선형화기 모델을 설계하였다. 제안된 모델의 성능평가는 37dBm GaN Doherty 전력증폭기와 ADS Tool을 사용하여 왜곡특성 성능개선정도를 검증하였다. 선형화된 GaN 전력증폭기의 2-tone 출력스펙트럼에서 약 16 dB의 왜곡개선효과를 보였다.

• 한국환경과학회지
• /
• 제12권2호
• /
• pp.207-215
• /
• 2003

The purpose of this study is to estimate the air quality of subway stations having underground platforms in Busan Metropolitan City, from September to November 2000, over seven times. The places of the investigation include Yonsan-dong station, Somyon station, Busan station, Nampo-dong station, and Dusil station. Samplings were conducted at three points in each station, i.e. gates, ticket gates, and platforms. CO, NO, $NO_2$, and $O_3$ were the main components of air for this analysis. In order to more fully understand station environments, we also measured an air temperature at each point. The results showed that the $O_3$ average concentration of Yonsan-dong station was higher than others with 38~51 ppb. The average concentration of NO was high at the ticket gate and platform at Somyon station (119 ppb, 122 ppb) and Nampo-dong station (102 ppb, 100 ppb). These results show that the air pollution of stations with underground shopping malls were higher than others. At Somyon station having a junction station, NO and $NO_2$ concentration levels of platform-2 (noncrowded) were higher than platform-1 (crowded). This is most likely due to the accumulation of air pollutants and inadequate ventilation systems. To find the relationship of the indoor (platform) and outdoor (gate), we analyzed the I/O ratio. The averages of CO and $O_3$ were both higher than one: 1.16 and 1.82, respectively. In the correlations between each material and the others, NO vs $NO_2$ was the highest with R=0.63. In the correlations between indoor and outdoor, $O_3$ was the highest with R=0.64.

• 대한치과보철학회지
• /
• 제36권2호
• /
• pp.336-354
• /
• 1998

Traditionally, many kinds of mechanical bonding techniques were used for bonding resins to the surface of the metal alloys. If there is a seperation between resin and metal junction by stress accumulation and temperature change of oral cavity, the cracks or crazing may occur, accompanied by failure of resin bonding to metal. This study was designed to compare the shear bond strength of the type IV gold alloy and Cr-Co alloy surfaces treated with various methods and thermocycling. Universal Instron (Model 1000) and scanning electron microscope (JEOL, Japan) was used to record the shear bond strength of 5 groups. Forty specimens were made for each group ; group 1 was treated with sandblasting only, group 2 was coated with V-primer after sandblasting, group 3 was coated with Metal primer, group 4 wase coated with MR Bond and group 5 was coated with silane. After treated with various methods, thermocycling was done for half of the each group. The surfaces of failed pattern were observed with SEM. The results were as follows : 1. Shear bond strength of the group 1 was lower than that of another groups in type IV gold alloys and bond strength of the group 1, 2 were lower than that of group 3, 4, 5 in Cr-Co alloys. 2. Shear bond strength of the gold alloy with resin was higher than that of Cr-Co alloy when specimens were coated with V-primer. 3. Shear bond strength of the Co-Cr alloys with resin was higher than that of gold alloys when specimens were coated with Metal primer. 4. The bond strength of all specimens did not decreased significantly after thermocycling. 5. Adhesive failures were found in group 1 and Cr-Co alloy in group 2, but adhesive and cohesive failures were found in another groups.

• 한국물환경학회지
• /
• 제34권3호
• /
• pp.285-292
• /
• 2018

This study was performed in order to identify the red tide-causing organism and to understand the characteristics of the water quality during the winter of 2015 and 2016 in the Oncheon stream, a tidal river in Busan, where red tide often occurs in the wintertime. Two sites were selected on the stream and the surface water was sampled a total of 28 times during the experimental period. Twelve water quality characteristics, including water temperature, pH, DO, COD, total-N (T-N), total-P (T-P), and salinity were analyzed in order to test water quality. The cell numbers of cryptomonads were counted directly by microscopic observation. The nucleotide sequences of the partial 28S rRNA gene and psbA gene from metagenomic DNA, derived from each sampling site, were analyzed. According to the results, the alga most responsible for the bloom was identified as Teleaulax OC1 sp., which belongs to the cryptomonads. Three items of chl-a, pH, and DO were positively correlated with the cell numbers of the cryptomonads counted at the upper stream of the tidal area (St 1) while eight items of chl-a, TOC, BOD, total-N, COD, SS, pH, and DO were positively correlated with the cells located at the junction between the stream and Su-young river (St 2) in the order.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.185-185
• /
• 2011

ZnTe semiconductor is very attractive materials for optoelectronic devices in the visible green spectral region because of it has direct bandgap of 2.26 eV. The prototypes of ZnTe light emitting diodes (LEDs) have been reported [1], showing that their green emission peak closely matches the most sensitive region of the human eye. Another application to photovoltaics proved that ZnTe is useful for the production of high-efficiency multi-junction solar cells [2,3]. By using the pulse laser deposition system, ZnTe thin films were deposited on ZnO thin layer, which is grown on (0001) Al2O3substrates. To produce the plasma plume from an ablated ZnO and ZnTe target, a pulsed (10 Hz) YGA:Nd laser with energy density of 95 mJ/$cm^2$ and wavelength of 266 nm by a nonlinear fourth harmonic generator was used. The laser spot focused on the surface of the ZnO and ZnTe target by using an optical lens was approximately 1 mm2. The base pressure of the chamber was kept at a pressure around $10^{-6}$ Torr by using a turbo molecular pump. The oxygen gas flow was controlled around 3 sccm by using a mass flow controller system. During the ZnTe deposition, the substrate temperature was $400^{\circ}C$ and the ambient gas pressure was $10^{-2}$ Torr. The structural properties of the samples were analyzed by XRD measurement. The optical properties were investigated by using the photoluminescence spectra obtained with a 325 nm wavelength He-Cd laser. The film surface and carrier concentration were analyzed by an atomic force microscope and Hall measurement system.

• Restorative Dentistry and Endodontics
• /
• 제23권2호
• /
• pp.682-689
• /
• 1998

The purpose of this study was to evaluate the sealing ability of the Microseal$^{(R)}$, which was new obturation system made by Tycom company, U.S.A. Forty-five extracted single-rooted human teeth were resected at cemento-enamel junction and divided three groups. All canals were prepared using Profile system, and then each group was obturated by lateral condensation technique (group 1), vertical condensation technique (group 2) and Microseal$^{(R)}$ condensation technique (group 3) with root canal sealer. Teeth were immersed in resorcinol-formaldehyde resin for 5 days at $4^{\circ}C$ and the resin was allowed to polymerize completely for 4 days at room temperature. Teeth were resected horizontally at 1 mm (level I), 2 mm (level II), 3 mm (level III) from the anatomical root apex using low speed microtome and examined with Image analyzer (IBASR, Zeiss co., Germany.) at ${\times}25$ magnification. The gab between the canal wall and the filling material, which was filled with the resin, was measured at each of the three levels. Each ratio of leakage was expressed percentage by calculating the ratio of the area of the resin to the total area of the canal and was analyzed statistically (one-way ANOVA). The results were as follows; 1. The mean ratio of leakage (%) was 6.46% at group 1, 3.06% at group 2, 11.27% at group 3. 2. When evaluating the ratio of leakage at the three levels, there was level I> level II> level III in all groups. Especially, the difference between level I and level III was statistically significant (p<0.05). 3. When evaluating the ratio of leakage at the three groups, there was group 3> group 1> group 2 at all levels. Especially the difference between group 2 and group 3 was statistically significant (p<0.05).

• 반도체디스플레이기술학회지
• /
• 제2권4호
• /
• pp.37-40
• /
• 2003

반도체 장비의 기능성과 신뢰성을 높이기 위하여 부품의 제조기술은 점차 마이크로 머신 기술을 요구하고 있다. 마이크로머신 기술 중 hot junction이 위치하는 멤브레인 구조는 각종 센서와 히터의 미세부품에서 가장 이용도가 큰 구조이다. 실험에서는 마이크로머신의 기본 구조인 멤브레인 형태를 만들기 위해 KOH 용액과 TMAH 용액으로 단결정 실리콘을 이방성 습식식각 하였다. 실험결과, 식각액의 온도와 농도, 마스크 패턴과 웨이퍼의 결정성의 일치 등을 고려해야 하며, 식각 속도는 KOH 농도 및 온도에 따라 크게 변함을 알 수 있었다. KOH 용액은 30 wt% 80~$90^{\circ}C$ 온도 범위에서 가장 좋은 특성을 나타냈다. 한편, TMAH용액이 실리콘을 식각하는 용액으로 관심을 끄는 것은 단결정에서 상대적으로 $SiO_2$ 박막을 마스크로 사용할 수 있을 뿐 아니라 $SiO_2$ 박막을 마스크로 사용할 수 있을 뿐 아니라 다른 식각액보다 찌꺼기가 적다는 장점 때문이다. 그러나, 다른 용액에 비해 가격이 고가이며 식각 속도가 낮다는 것이 실용적인 측면에서 큰 단점이다. 실험결과를 종합적으로 고려할 때 KOH 용액 농도 30wt%와 온도 $90^{\circ}C$가 마이크로머신 기술에 의한 멤브레인 구조 제작에서 적합한 공정조건이라고 할 수 있다.